Pioneer PRO-710HD Service Manual page 121

QQ
3 7 63 1515 0
Table 2 OFFSET CONVER DATA
OFFSET CONVER MODE 1
Numeric
Adjustment
Key
Item
1 DFH
2 DFV
3 HDP
OFFSET CONVER MODE 2
Numeric
Adjustment
Key
Item
1 HFP
2 HCP
3 HTP
4 HHD
5 HPW
6 V1C
7 V1S
8 VFP
The above offset convergence values are common to the PRO-610
HD/510HD and SD-582HD5/532HD5.
If the offset convergence values are as indicated in Table 2,
TE
L 13942296513
proceed to 3.3. If the values are not the same, adjust the values
with the numeric keys and VOL +/– keys.
Example:
To check HDP in ZOOM mode of OFFSET CONVER. MODE 1
1 Enter the FACTORY mode.
2 Enter the OFFSET CONVER. MODE 1 by pressing the DOT
key once.
3 Enter the ZOOM screen mode by pressing the SCREEN mode
key once. (When the unit enters FACTORY mode, the screen
mode automatically becomes FULL.)
4 Check the indication on the screen by pressing the numeric
key 3.
Indication at the bottom of the screen : Z HDP 010
If the adjustment value is 010, adjustment is not required.
If the adjustment value is other than 010, adjust with the VOL
+ or VOL- key so that the value becomes 010.
3.3 Coarse Adjustment of the Green
(Proceed with 3.3 and afterwards when the DIGITAL CONV.
Assy is not replaced.)
Select adjustment items (STATIC and SIZE of vertical and
horizontal lines, etc.) for each GH and GV, and adjust to roughly
eliminate distortion. (For GV, peripheral pin distortion adjust-
www
ment is necessary.)
Press the DOT key three times to enter OFFSET CONVER.
MODE 3.
Press the SCREEN mode key and proceed with the adjustment for
.
each screen mode.
http://www.xiaoyu163.com
Screen Mode
F Z C N
FULL ZOOM CINEMA NATURAL
1A0 180 180 180
0F0 0D0 0D0 0D0
070 070 070 070
010 010 010 010
Screen Mode
F Z C N
FULL ZOOM CINEMA NATURAL
0CC 0CC 0CC 0CC
00F 00F 00F 00F
047 047 047 047
0EE 0EE 0EE 0EE
00C 00C 00C 00C
01F 029 025 022
000 000 000 000
01D 02D 013 033
x ao
y
i
http://www.xiaoyu163.com
PRO-710HD, PRO-610HD, PRO-510HD,
8
The cross-hatch signal is generated inside the unit, and is auto-
matically displayed in OFFSET CONVER. mode and MANUAL
CONVERGENCE mode. You can turn on and off the cross-hatch
signal with the YELLOW key.
H
HD FULL
1B0
100
070
010
H
HD FULL
0CA
A
00F
Screen mode:
04A
F : FULL
0E9
Z : ZOOM
00F
C : CINEMA
01D
N : NATURAL
000
H : FULL for HD
065
The Screen modes change cyclically with each press of the
SCREEN mode key.
B
Q Q
3 6 7 1 3
Cyclically changes with the CH+ or CH- key as follows:
C
Adjustment items can be selected with the numeric keys.
See Table below.
• Waveforms adjustable in the coarse adjustment
of the green
Numeric Key
0
1
6
8
D
Adjustment data:
MAX 1FF
100
001
CNT 000
3FF
2FF
MIN 200
u163
Data can be adjusted with the VOL+ and VOL- keys.
.
SD-582HD5, SD-532HD5
2 9 9 4 2 8
Screen indication
STATIC
F RH 001
A B C D
1 5 0 5 8 2 9 9 4
RH RV BH
GV GH BV
GH GV
STATIC STATIC
SKEW SKEW
PIN
SIZE SIZE
m
co
9 9
2 8 9 9
121