Acer PD726W User Manual
Hide thumbs Also See for PD726W:

Advertisement

Product Features

This product is an XGA single chip 0.7" DLP
standing features include:
True XGA, 1024 x 768 addressable pixels
u
Single chip DLP
u
NTSC3.58/NTSC4.43/PAL/SECAM and HDTV
u
compatible (480i/p, 576i/p, 720p, 1080i)
Dual resolution support:
u
High-tech HDMI and DVI connection for digital signal
-15:9 (1280 x 768)
with HDCP function and supports 480p, 576p, 720p and
1080i formats
-16:9 (1280 x 720 )
User friendly and powerful Acer Empowering key
u
including: Acer eView Management, Acer eTimer
Management and Acer eOpening Management.
Full function remote control with laser pointer
u
Advanced digital keystone correction and high quality
u
full screen image re-scaling
User friendly control panel
u
SXGA, XGA compression and VGA, SVGA re-sizing
u
Support HDMI input with HDMI 1.0 compliant
u
Supports High bandwidth Digital Content Protection
u
– HDCP 1.1 on HDMI input
Mac compatible
u
Introduction
TM
technology
TM
projector. Out-

... English

Advertisement

Table of Contents
loading

Summary of Contents for Acer PD726W

  • Page 1: Product Features

    True XGA, 1024 x 768 addressable pixels Single chip DLP technology NTSC3.58/NTSC4.43/PAL/SECAM and HDTV compatible (480i/p, 576i/p, 720p, 1080i) Dual resolution support: High-tech HDMI and DVI connection for digital signal -15:9 (1280 x 768) with HDCP function and supports 480p, 576p, 720p and 1080i formats -16:9 (1280 x 720 ) User friendly and powerful Acer Empowering key including: Acer eView Management, Acer eTimer Management and Acer eOpening Management. Full function remote control with laser pointer Advanced digital keystone correction and high quality full screen image re-scaling User friendly control panel SXGA, XGA compression and VGA, SVGA re-sizing Support HDMI input with HDMI 1.0 compliant Supports High bandwidth Digital Content Protection – HDCP 1.1 on HDMI input Mac compatible...
  • Page 2: Connection Ports

    3. DVI Input Connector 4. VGA Input Connector (PC Analog Signal) 5. Component Video Input Connector 6. S-Video Input Connector 7. RS232 Connector 8. Kensington Lock Port 9. Power Socket 10. VGA Output Connector (Monitor Loop-through Output Connec- tor) 11. Audio Input Connector 12. Composite Video Input Connectort Below items are for PD726W only: 13. Lan (RJ45 Port for 10/100M Ethernet) 14. Audio Output Connector 15. Reset Button 16. Status Indicator 17. Antenna ... English...
  • Page 3: Installation

    Installation Connecting the Projector For Wireless function poor image and font quality Internet 1........................Power Cord 2......................... Lan Cable 3....................Audio Cable Jack/Jack 4..........................Antenna (for PD726W only, need to attach the antenna by user) English ...
  • Page 4: User Controls

    User Controls Color Press “Color” adjust the color temperature of image.  Contrast Press “Contrast” control the difference between the  darkest parts lightestand of the picture. Press “VGA” to change source to VGA-In connector. This con-  nector supports Analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync. Component to change source to component connec Press “Component”  tor. This connector supports YPbPr (480p/576p/720p/1080i) and YCbCr (480i/576i) Video to change source to Composite Video Press “Video”  source. S-Video change source Press “S-Video” to to S-Video source.  Press “DVI” to change source to DVI connector. This connector  supports Digital RGB, Analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and HDCP signal. HDMI P ress “HDMI” to change source to HDMI. This connector can ...
  • Page 5: Aspect Ratio

    User Controls Image (Computer / Video Mode) H. Keystone (Horizontal Keystone) Press the or button to adjust image distortion horizontally  and makes a squarer image. V. Keystone (Vertical Keystone) Press the or button to adjust image distortion vertically  Auto : Keep the image with original and makes a squarer image. width-higth ratio and maximize the Aspect Ratio image to fit native horizontal or vertical pixels.
  • Page 6: Signal Type

    User Controls Image (Computer / Video Mode) H. Position (Horizontal Position) Press the to move the image left.  Press the to move the image right.  “H. Position”, “V.  V. Position (Vertical Position) Position”, “Frequency” and “ Tracking” func- Press the to move the image down.  tions are not supported Press the to move the image up. under DVI and Video  mode. Frequency “Frequency”changes the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Tracking “Tracking” synchronizes the signal timing of the display with the graphic card. If you experience an unstable or flickering image, use this function to correct it.
  • Page 7 User Controls Management (Computer / Video Mode) Lamp Reminding Choose this function to show or to hide warning message when the changing lamp message is displayed. The message will show up 30 hours before end of life. Security Press to start “Security” setting. If the “Security” function is enabled, your must enter “Administrator Password” first before Security setting. Security This projector provides an excellent security function for the administrator to manage the usage of the projector. Select “On” to enable the security function. User  have to enter password depending on the " Security Mode" . Please refer to "User Password" section for details. Select “Off” then user can switch on the projector  request. without password. Once the security function is enabled, the projector will request user to enter password when switch on the projector or enter security setting. Both “User English ... Password” and “Administrator Password” can be accepted for this dialogue.
  • Page 8 User Controls Management (Computer / Video Mode) The projector provide two options of "Security Mode". Select “Request password only after plugging  power cord”, the project will request user to input password only for the first time plugging on power cord of the projector. Select “Always request password while projector  turns on”, user have to input password every time when switching on the projector. Administrator Password “Administrator Password” can be accepted by both “Enter Administrator Password” and “Enter Password” dialogues. Press to change “Administrator Password”.  Projector will request “Administrator Password” before changing password. Should be "Set Administrator Password" dialogue. English ... The factory default of “Administrator Password” is  “1234”.
  • Page 9 User Controls Management (Computer / Video Mode) If user or administrator forgot “User Password” or even “Administrator Password”, do the following to retrieve the “Administrator Password”: 1.Press “MENU” for more than 4 seconds when any of “Enter Password” or “Enter Administrator Password” dialogue is currently displayed. 2.Write down the “Unlock ID” and contact with Acer service center. They will give you new Administrator Password according to the Unlock 3.Once the new “Administrator Password” retrieved from Acer has been logged into the projector, old “Administrator Password” will be replaced by the new password. Reset Press the button after choosing “Yes” to return the display ... English parameters on all menus to the factory default settings.
  • Page 10: Wireless Projection

    Wireless projection Introduction This section will introduce wireless projection function for this projector. The wireless projection function is only available for the model which is equipped with integrated Acer Wireless Presentation Gateway (WPG) module. Acer WPG enables multiple users to connect to an Acer projector wirelessly. This eliminates the need to plug and unplug cables, enabling more efficient use of meeting time, especially when there is more than one presenter in a meeting. To perform wireless projection, you have to change the input source type to "Wireless"...
  • Page 11: Specifications

    Appendices Specifications Specifications The specs specified below are subject to change without notice. Regarding the final specs, please refer to Acer accounced marketing specs. Light Valve - Single Chip DLP Technology by Texas Instruments Lamp - 300W User Replaceable Lamp Number of Pixels - 1280 pixels(H) X 768 lines(V) 1024 Displayable Color - 16.7M colors Contrast Ratio - 2300:1 (Full On/Full Off) 2500 Uniformity - 90% Noise Level - 30dB(A)(standard mode / 28dB(A)(ECO mode) Projection Lens - F/2.4~2.6 f=28.0~33.6mm with 1.2X Manual zoom lens 24.6 Projection Screen Size (Diag.) - 36 to 300 inches Diagonal Projection Distance - 3.94 to 40.03 feet (1.2 to 12.2 meters) Video Compatibility - NTSC 3.58/NTSC 4.43/PAL/SECAM and HDTV...
  • Page 12 Appendices 4. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged. 5. This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. 6. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. 7. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product. 8. Do not attempt to service this product yourself, as opening or remov- ing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 9. Unplug this product from the wall outlet and refer servicing to quali- fied service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating in- structions are followed. Adjust only those controls that are cov- ered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. e. If the product has been dropped or the case has been damaged. If the product exhibits a distinct change in performance, indicating a needfor service. 10. T o avoid hazard of unexpected electrical shock, use the AC adapter only when the wall socket is properly grounded. Add wireless section, copy from the last pages of PD5XX English ...

This manual is also suitable for:

Pd726w

Table of Contents