Page 2
Congratulations on purchasing a Brivis Touch Comfort Controller. This intelligent Controller can be used with a range of Brivis heating and cooling products. The Brivis Touch allows you to maximize the performance of your heating and cooling system with customized comfort control.
1.0 Quick Reference Guide Diagram 1: Heating screen in Manual Operation Current System Mode Display Options or Settings Fan Status Indicator Fan Only mode Digital Clock Zone ID (where fitted) ON/OFF Mode Selector Room / Zone Temperature Zones (Where Fitted) Manual or Schedule System Mode/Run indicator Room temperature sensor active...
Page 5
Diagram 2: Evaporative Cooling Screen Diagram 3: Refrigerated Cooling Screen Fan On Pump On Manual / Auto Timer Timer On...
The system will operate to maintain the desired temperature level until turned OFF. 4.1 Heating – Program Schedule Operation The Brivis Touch Controller uses default ‘energy saver’ HEAT settings that helps reduce your heating expenses. Note: Time period “Pre-Sleep” can be enabled in the “User Preferences”...
OFF. The word “Temporary” will flash on the screen. 5.1 Cooling – Program Schedule Operation The Brivis Touch Controller uses default ‘energy saver’ COOL settings Diagram 6: Heating Temperature Override that helps reduce your refrigerated cooling expenses.
Page 9
Temporary Temperature Override Diagram 7: Cooling ON – Schedule home screen To temporarily adjust the temperature, simply adjust the temperature level with the UP/DOWN arrows. The program Schedule will automatically resume once one of the following occurs: • The next time period begins. •...
6.0 Evaporative Cooling – Manual Operation 6.3 Evaporative Cooling– Auto Operation To operate your Evaporative Cooling system with full manual control, To operate your Evaporative Cooling system so that it automatically activate the Controller by touching the LCD screen, select EVAP using maintains your desired comfort level, activate the Controller by the MODE button, turn system on using the ON/OFF button.
6.5 Evap Timer ON – Manual / Auto To save settings and return to the home OFF screen press “Done”. To With the system in “EVAP” mode and OFF, press the “Timer” button, cancel Timer setting press “BACK”. refer Diagram 12. Diagram 12: EVAP mode in OFF state Diagram 13: Manual –...
To save settings and return to the home OFF screen press “Done”. To 6.6 Evap Timer OFF – Manual / Auto cancel Timer setting press “BACK”. With the system ON in either MANUAL or AUTO mode, press the Diagram 14: Auto – Set On Timer “Timer”...
(or cooled) simultaneously. Your system may be operated manually, or you can program your comfort schedule and let the system automatically do the rest. Multiple Brivis Touch Controllers or Temperature Sensors may be fitted. 7.2 Multi Temperature Set Point Zoning (MTSP) The following information applies to HEATING or REFRIGERATED COOLING systems only (i.e.
Diagram 18: MTSP Zone Selection Note: Once you access the MENU Screen and select a configuration option, if no button is pressed for 60 seconds, the Touch will exit the configuration mode and return to normal operation; this applies to all options other than SCHEDULE.
PIN codes to be set or reset, refer Diagram 21. Note: All Brivis Touch Controllers are able to lock and unlock the system – only the Master Controller allows you to change the PIN.
Diagram 24: Active backlight delay 9.3 System Settings When the “System Settings” button is pressed on the Master Brivis Touch Controller the system settings can be defined, refer Diagram 26. Diagram 26: System Settings Diagram 25: Dimmed backlight delay The “Schedule Day Grouping” option allows the customisation of days when programming the AUTO schedule.
30 By pressing a zone, a keypad appears to enable the zone name seconds. This allows the Brivis Touch Controller screen to be cleaned change, refer Diagram 28. without affecting any operation, refer Diagram 30.
To access the Heating Schedule the system must be in HEAT mode 11.0 Schedule and access is through “MENU” > “Schedule”. The default time and temperature values for each period are set as shown in Diagram 31 and Diagram 32 for Heating and Cooling To access the Cooling Schedule the system must be in COOL mode respectively.
When the “Set Day/Time” button is pressed on the Master Brivis When the operating hours logged for an appliance exceeds the Touch Controller this allows the day, time and time period to be predetermined period, the Brivis Touch Controller displays the changed, refer Diagram 33.
16.0 Power Outages If power is restored within 10 minutes of a power outage, the Brivis Touch will resume normal operation with the mode and settings immediately before the outage.
Single Temperature Set Point (STSP) System Sensor The zone temperature set point is the same across all Touchscreens Both the Brivis Touchscreen and Remote Temperature Sensors and/or Temperature Sensors. function as zone (room) temperature sensors – in this context, the word “sensor”...