Kantech kt-100 Installation Manual
  1. Manuals
  2. Brands
  3. Kantech Manuals
  4. Network Router
  5. kt-100
  6. Installation manual

Kantech kt-100 Installation Manual

Door controller
Hide thumbs Also See for kt-100:
Table of Contents

Advertisement

Quick Links

WARNING: This manual contains information on limitations regarding product use
and function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
K T - 1 0 0
I n s t a l l a t i o n M a n u a l
Kantech Systems - Access Control and Accessories
DN5073-0205-0207
D o o r C o n t r o l l e r
™

Advertisement

Table of Contents
loading

Related Manuals for Kantech kt-100

Summary of Contents for Kantech kt-100

  • Page 1 D o o r C o n t r o l l e r ™ I n s t a l l a t i o n M a n u a l Kantech Systems - Access Control and Accessories DN5073-0205-0207...
  • Page 2 Products names are trademarks or registered trademarks of their owners. No part of this publication may be reproduced in any form without permission from Kantech Systems, Inc. Kantech Systems Web Site: www.kantech.com © 2002, Kantech Systems All rights reserved. Specifications may be modified without notice.

  • Page 3: Table Of Contents

    Tab l e of c o n t e nt s Section 1: KT-100 Features Section 2: M ounting and W iring the KT-100 Door Controller Step 1•Unpacking the KT-100 ..........5 Step 2•Selecting a Mounting Location .........5 Step 3•Installing the Power Supply ........5 Step 4•Installing the KT-100 Unit ........5...

  • Page 5: Section 1: Kt-100 Features

    It also monitors all the door reader. For details about using the KT-100 Controller to equipment for any failure or tampering. Any abnormal interface another alarm panel, refer to “Using the KT-100 with...
  • Page 6 K T - 1 0 0 I n s t a l l a t i o n M a n u a l...

  • Page 7: Controller

    NOTE: Power should only be applied to the unit when all con- nections are completed and tested. The KT-100 Controller has been designed to be mounted on a For details on installing the KT-PC4204, refer to “Mounting the wall in a single gang electrical box without any additional KT-PC4204”...

  • Page 8: Step 5•Connecting The Door Locking Device

    NOTE: Use 1K ohm end-of line resistor between +12VDC and NC if not used. This resistor is already included in the box (KT- The KT-100 has an on-board capability of monitoring 4 input 100-ACC). zones. Each input is supervised with or without end-of-line resistors (5.6K ohm).

  • Page 9: Step 7•Connecting Readers And Keypads

    Optional Connecting Control Relay Outputs Step 8• 5,6K End of Line Resistor The KT-100 provides two opto-isolated contacts (R1 & 2) and two control outputs (R3 & 4). R1 & 2 can be used as either as dry contacts. ◗...

  • Page 10: Step 10•Connecting The Kt-100 To The Rs-485 Bus

    120 ohms EOL resistor RS485 NETWORK: UNSHIELDED TWISTED PAIRS CABLE AWG #22 (1200 METERS MAX) NOTE: After you have completed all the necessary steps, you may power the KT-100 by connecting the AC power and the bat- tery. TAMPER SWITCH...

  • Page 11: Section 3: Appendix

    I n s t a l l a t i o n M a n u a l S e c t i o n 3 : A p p e n di x Typical KT-100 Wiring Diagram NC Dry contact Controller defined without...

  • Page 12: Kt-100 Compliance Notices

    Problems This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: The KT-100 default initialization is done at Kantech. The ◗ (1) this device may not cause harmful interference, following steps should only be done if: ◗...

  • Page 13: Kt-100 Controller Maintenance

    Mounting the KT-PC4204 To ensure the best operating conditions, it is highly The KT-PC4204 package should include the following items: ◗ recommended to test the KT-100 controller by performing the One KT-PC4204 circuit board, following tests. ◗ One ground wire assembly, ◗...

  • Page 14: Using The Kt-100 With An External Alarm Panel

    The KT-100 output (Relay 4, in the example) is connected to a local bell or to warn the alarm panel Connect the KT-100 two inputs (zone 3 and 4) to the of an abnormal condition from the door. external alarm status relay (PGM1 and PGM2) ◗...
  • Page 16 Kantech Systems Web Site: www.kantech.com © 2002, Kantech Systems. All rights reserved. Specifications may be modified without notice. ™ Trademarks of Kantech Systems. Printed in Canada • DN5073-0205-0207...

Table of Contents