Advertisement
FA311/312.QCard.NewSize 1/23/01 8:34 AM Page 2
4. Select "Floppy disk drives" and insert the NETGEAR FA312 Fast Ethernet PCI Adapter
Drivers and Diagnostics disk into the floppy drive. Click on "Next."
5. Click on "Next" in the Update Device Driver Wizard.
6. When the "Network" window opens, enter a name (a different one-word name for each com-
puter) in the "Computer name" entry field; enter a workgroup name (the name of your entire
network) in the "Workgroup" entry field. Click on "OK."
7. When asked to insert the NETGEAR FA312 Fast Ethernet PCI Adapter Drivers disk, click
on "OK."
8. Type A:\ in the "Copy files from" entry field and click on "OK." The system copies the files
from the driver diskette.
9. Make sure the Windows 98 CD-ROM disk is in the system, and click on "OK" when prompted.
10. Make sure the designated path to the Windows 98 CD-ROM is displayed in the "copy files
from" prompt line (for example, D:\WIN98).
11. In the "Update Device Driver Wizard" dialog box, click on "Finish."
12. Remove the NETGEAR FA312 Drivers and Diagnostics disk and the Windows 98 CD-ROM.
When asked if you want to restart your computer, click on "Yes."
You must restart your computer to complete the installation of the driver.
VERIFY INSTALLATION
VERIFY INSTALLATION
1. Double-click on "My Computer" on the desktop.
2. Double-click on "Control Panel."
3. Double-click on "System."
4. Click on "Device Manager."
5. Double-click on "Network adapters."
6. If there is a problem with the installation of the driver, an exclamation point appears next to
"NETGEAR FA312 Fast Ethernet PCI Adapter." If there is an exclamation point, double-click
on "NETGEAR FA312 Fast Ethernet PCI Adapter." The "Properties" window opens, and a
message regarding the status of the device is displayed in the window. Continue to click on
"OK" or click on the "X" in the right-hand corner to close any open windows and return to the
Windows desktop.
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Model FA311 or Model FA312 Network Card
Standards Compatibility
NetWare tested and approved Microsoft Windows 95,Windows 98, Windows NT
®
compatible
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3i 10BASE-T Ethernet
Auto-sensing PCI Plug and Play 2.1 or 2.2 compatible
Network Interface
RJ-45 connector for 10BASE-T or 100BASE-TX
Power
Power consumption: 3 W max.
DC operating voltage: +5 +/- 5% @ 630 mA maximum
Physical Specifications
Dimensions: 5.7 by 3.7 in. (14.4 by 9.3 cm)
Weight: 0.20 lb. (90 g)
Environmental Specifications
Operating temperature: 0 to 40ºC
Operating humidity: 10 to 90% non-condensing
Warranty Information
Limited lifetime
© 2000 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a trademark of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. All other trademarks and registered trademarks are the property of their respective owners.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice. NETGEAR does not assume any liability
that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model FA311 Network Card and Model FA312 Network Card have been suppressed
in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of
some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to cer-
tain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
Note:
Modifications to this device change it from the original state it was in when tested and may alter the
device so that it no longer complies with FCC testing limitations for Class B digital devices. According to
FCC regulations, the user could be prohibited from operating this equipment if it is modified.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
Declaration of Conformity
NETGEAR Model FA311 Network Card
NETGEAR Model FA312 Network Card
Tested to comply
Tested to comply
with FCC Standards
with FCC Standards
FOR HOME OR OFFICE USE
FOR HOME OR OFFICE USE
EN 55 022 Statement
This is to certify that the Model FA311 Network Card and Model FA312 Network Card are shielded against the
generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class B (CISPR 22). Compliance is dependent upon the
use of shielded data cables.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Model FA311 Network Card and Model FA312 Network Card) do not exceed the Class B
limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (Model FA311 Network Card et Model FA312 Network Card) respecte les limites de bruits
radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélec-
trique du ministère des Communications du Canada.
Hardware Warranty Information
Subject to the provisions described below, this NETGEAR product is protected by a limited lifetime warranty from
defects in material and workmanship.
Should a product fail to perform as described above within the first year following the original date of purchase,
NETGEAR will ship a replacement for the failed product upon return of the defective product.
Products that fail after the first year following the original date of purchase will be repaired or replaced with the
same or functionally equivalent, product by NETGEAR, at its discretion, free of charge provided you (1) have, within
30 days of the original date of purchase, completed and returned the Owner Registration Cards which accompanied
the products when shipped, (2) return the failed product to NETGEAR designated repair facility with shipping
charge prepaid, and (3) provide NETGEAR with proof of the original date of purchase. Repaired or replacement
products will be returned to you with shipping charges prepaid.
Replacement products may be refurbished or contain refurbished materials. If NETGEAR, by its sole determination,
is unable to repair or replace the defective product, it will refund the depreciated purchase price of the product.
This warranty does not apply if, in the judgement of NETGEAR, the product fails due to damage from shipment,
handling, storage, accident, abuse or misuse, or if it has been used or maintained in a manner not conforming to
product manual instructions, has been modified in any way, or has had any serial number removed or defaced.
Repair by anyone other than NETGEAR or an approved agent will void this warranty. The maximum liability of
NETGEAR under this warranty is limited to the purchase price of the product covered by the warranty.
Prior to returning any defective product, the end customer or the reseller from whom the end customer
originally purchased the product must obtain a Return Materials Authorization (RMA) number from NETGEAR.
All defective products should be returned to NETGEAR with shipping charges prepaid. NETGEAR will not accept
collect shipments.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT OR AS REQUIRED BY LAW, THE WAR-
RANTIES AND REMEDIES STATED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, ORAL OR
WRITTEN, EXPRESS OR IMPLIED. ANY AND ALL OTHER WARRANTIES, INCLUDING IMPLIED WAR-
RANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT
OF THIRD PART RIGHTS ARE EXPRESSLY EXCLUDED. NETGEAR SHALL NOT UNDER ANY CIRCUM-
STANCES BE LIABLE TO ANY PERSON FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUEN-
TIAL DAMAGES, INCLUDING WITHOUT LIMITATION, DAMAGES RESULTING FROM USE OR MALFUNC-
TION OF THE PRODUCTS, LOSS OF PROFITS OR REVENUES OR COSTS OF REPLACEMENT GOODS.
EVEN IF NETGEAR IS INFORMED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES.
Advertisement
