Related Manuals for Packard Bell EasyNote K5
Summary of Contents for Packard Bell EasyNote K5
- Page 1 EasyNote K5 EasyNote K5 Disassembly Manual Version 1.1 Required Tools • Disassembly Instructions • DIP Switch Setting • Reassembly Instructions •...
-
Page 2: Required Tools
EasyNote K5 Required Tools All EasyNote K5 maintenance procedures can be performed using the following tools: Tweezers Small Philips screwdriver Small Flat screwdriver Hex bolt screwdriver Ø... -
Page 3: Disassembly Instructions
EasyNote K5 Disassembly Instructions This document contains step-by-step disassembly instructions for the EasyNote K5. The instructions are clarified by images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves. - Page 4 EasyNote K5 1. Battery Remove the battery pack of the notebook as follows: a. Unlock the battery. b. Pull outward and lift up the battery. Fig. 1: Remove Battery.
-
Page 5: Hard Drive
EasyNote K5 2. Hard Drive To remove hard drive: a. Unscrew two screw on hard disk module at the bottom of unit b. Carefully slide the hard disk module out from base unit. Fig. 2: Hard Disk Module c. Unscrew six screws at the side of the hard disk module Fig. - Page 6 EasyNote K5 3. 2 Memory Slot & MDC Modem a. Unscrew eight screws to open SO-DIMM Slot & MDC Modem cover. b. Release the SO-DIMM memory module. c. Remove the memory module. Fig. 4: SO-DIMM Slot & MDC Modem Cover.
-
Page 7: Optical Drive
EasyNote K5 4. Optical Drive a. Loosen three screws at bottom. b. Push optical drive out form unit through the gaps near to third screw. Fig. 6: Optical Drive. 5. Keyboard Cover & Keyboard a. Push toward left to release Keyboard Cover. - Page 8 EasyNote K5 b. Unscrew three screws that secure the keyboard. Fig. 8: Keyboard. c. Disconnect keyboard connector. Fig. 8: Keyboard Connector.
- Page 9 EasyNote K5 6. 1st RAM Slot a. Open up the black plastic cover and remove RAM from 1 RAM slot. Fig. 9: 1 RAM Slot. 7. CPU b. Unscrew five screws on the CPU Fan module, disconnect fan connect before remove it from base.
- Page 10 EasyNote K5 c. Unscrew three heat sink screws and disconnect the fan connection. Fig. 11: Heat sink assembly d. Carefully lift up heat sink assembly. Fig. 12: Heat sink assembly...
- Page 11 EasyNote K5 e. Unlock the CPU from CPU socket and lift up CPU with care. Fig. 13: CPU socket...
-
Page 12: Lcd Module
EasyNote K5 8. LCD Module a. Disconnect LCD connector at both sides. Fig. 14: LCD cable. b. Loosen four screws from the hinges before lifting up the LCD panel. Fig. 15: LCD module. - Page 13 EasyNote K5 9. LCD Panel Disassembly a. Remove four screws on LCD bezel. Fig. 16: LCD module b. Push at edge of LCD bezel toward inside and carefully separate it from LCD base. Fig. 17: LCD Bezel.
- Page 14 EasyNote K5 Fig. 18: LCD Panel. c. Unscrew two screws (C) on inverter board. d. Disconnect inverter board. e. Take away the inverter board. f. Unscrew eight screws (A&B) that hold the LCD brackets onto the LCD base cover. g. Lift out the LCD panel assembly.
-
Page 15: Main Board
EasyNote K5 10. MainBoard a. Loosen five screws on top cover. Fig. 19: Top Cover b. Unscrews seventeen screws on the bottom cover. Fig. 20: Bottom Cover... - Page 16 EasyNote K5 c. Loosen four hexbolts and one screw at the rear of the base unit. Fig. 21: Rear Cover d. Carefully lift up the bottom cover. Fig. 22: Bottom Cover...
- Page 17 EasyNote K5 e. Carefully lift up the main board assembly from top cover. Fig. 23: Main Board assembly f. Disconnect fan connector at the side of CPU socket Fig. 24: CPU Socket...
- Page 18 EasyNote K5 g. Remove four screws and disconnect fan connection on main board. Fig. 25: Main Board assembly h. Carefully separate the main board from heat plate. Fig. 26: Main Board...
-
Page 19: Audio Board
EasyNote K5 11. Audio Board a. Open eight screws on the audio board and disconnect five connectors before separate it from top cover. Fig. 27: Audio Board 12. Speaker a. Loosen four screws at both side of speaker before you can remove it from front cover. -
Page 20: Touch Pad
EasyNote K5 13. Touch Pad a. Unscrew one screw on the touch pad before remove it from top cover. Fig. 29: Touch Pad 14. LED Board a. Remove three screws on LED Board before separate it from top cover. Fig. 31: LED Board... -
Page 21: Dip Switch Settings
DIP Switch Settings No DIP switches available on the EasyNote K5 (Kigem) mainboard. ¡ £ ¢ ¤ ¥ ¦ § © ¨ ¡ £ ¢ ¤ ¥ ¦ § © ¨...