High performance compact coffee dispenser olc1 series (14 pages)
Summary of Contents for kaffee konzepte FK-series
Page 1
FK Range - Coffee dispensers FK Range Coffee Dispensers Set Up and User Guide FK-series - 1 -...
Page 2
FK Range - Coffee dispensers Notice Every effort has been made to ensure that the information contained in this manual is up to date and correct. However, the author, publisher or manufacturer will not accept liability for any loss or damage caused resulting from any errors in or omissions from information contained in this document.
FK Range - Coffee dispensers Index of contents Using the dispenser ..................4 Quick start ....................4 Refilling Coffee Concentrate ..............5 Refilling Powder products .................5 Cleaning the dispenser.................5 Semi-automatic cleaning cycle ..............5 Basic manual flush of valves and mixers ..........6 On demand flush cycle ................6 General cleaning..................6 Dispenser user functions (Set-up mode): .............6 Dispense counters ..................6...
1. The display and lighting on the front panel will illuminate. 2. The display will show a name (e.g. Kaffee Konzepte or AROMAT) on the top line and the word ‘Filling’ on the lower line. The machine will perform a ‘self check diagnostic’...
FK Range - Coffee dispensers For a can: Defrost the can fully and give it a shake to stir up the coffee solids. • Open the ring pull and insert the suction tube into the can. For a BIB: Defrost the BIB fully and give it a shake to stir up the coffee solids. •...
FK Range - Coffee dispensers 6. Remove the cleaning bottles and/or the cleaning adapters. 7. When the cleaning function is completed the lights will cease blinking and remain on. The cleaning cycle must be fully completed before the blinking will stop.
FK Range - Coffee dispensers Setup mode Press button to step to next option. Setup mode enables the selection buttons to be enabled or disabled and allocates recipes to each button. It also provides the ability to modify a recipe to suit the user.
FK Range - Coffee dispensers Recipe Bank Display shows:- Recipe bank Enter selects Press button to step to next option or press button to enter the Recipe bank. The dispenser contains a bank of pre-programmed drinks that may be allocated to any selection button (only FK12). This enables the ability to setup the drink selections very quickly.
FK Range - Coffee dispensers Display shows:- Press Selection 1. Press the selection button of the drink you wish to adjust. Display shows:- Selection XX Volume (+/- =Y) (XX = number from 1 to 12) (Y = number from -30 to +30, these numbers represent 1/10th second of dispense time) 2.
FK Range - Coffee dispensers Engineer mode functions: Hold down the ‘STOP’ button then press and release the (ENTER) button after 1 second but continue to press the ‘STOP’ button for a further 5 seconds to enter the Engineer mode functions:- Display shows:- Engineer setup Enter selects...
FK Range - Coffee dispensers buttons to adjust the heating program to the number of elements being used, 1 Element = 230vac 13A, 1 phase, normal Schuko plug setting. 2 Elements = 230vac 30A 1 phase or 30A, 2 live wire 3 phase 3 Elements = 45A 1 phase or standard 3 phase, normal 3 phase setting.
FK Range - Coffee dispensers FK20 2 products - Dispenser using 2 liquid coffee cans or BIBs of different coffee types. FK20 1 product - Dispenser using 2 liquid coffee cans or BIBs of the same coffee type. buttons to select this function type Calibrating concentrate pumps This function is used to calibrate the speed of the coffee pump (Pump 1).
FK Range - Coffee dispensers Concentrate sensors This function enables or disables the Liquid coffee sensor/s Press button Display shows:- Product sensors Enabled / disabled buttons to select sensor operation Boiler temperature calibration This function is used to calibrate the temperature and match the temperature displayed on the display to the actual temperature of the boiler when read from a thermometer placed in the water tank.
FK Range - Coffee dispensers Lighting setting This function enables brightness adjustment of the Front panel illumination. Press button Display shows:- Set LED level buttons to adjust the brightness of the front panel lights X = numbers 0 to 255, setting 255 =lamps off and 0 = lamps full on Coffee sensor ‘Detect’...
FK Range - Coffee dispensers Coffee detect CS=XXX DP=XXX CS = the value read by the Coffee sensor, (only shown for reference). DP = the value set by the system as the trip point at which the machine decides that coffee is present or not and is only shown for reference. When the calibration is complete the display will show Calibrated or FAIL.
FK Range - Coffee dispensers Firmware version This shows the version of the firmware installed in the processor and the date it was compiled. Display shows:- Firmware V: VX.X.X Comp DD-MMM-YY EEPROM software version This shows the version of the software installed in the EEPROM Display shows:- EEPROM ver XXX Water sensor calibration...