1. Manuals
  2. Brands
  3. BD Manuals
  4. Saw
  5. HP14
  6. Owner's manual and operating instructions

BD HP14 Owner's Manual And Operating Instructions

Slab saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HP14 Slab Saw
Owner's Manual and Operating Instructions
Revision 111
Manual Part No. 167671
Caution: Read all safety and operating
instructions before using this equipment.
This manual MUST accompany the
equipment at all times.
01.2016
MADE IN USA
Barranca Diamond Products, Inc.
1315 Storm Parkway
Torrance, CA 90501
Toll-Free: (800) 630-7682
Phone: (310) 523-5867
Fax: (310) 257-3063
www.barrancadiamond.com

Advertisement

Table of Contents
loading

Related Manuals for BD HP14

Summary of Contents for BD HP14

  • Page 1 HP14 Slab Saw Owner's Manual and Operating Instructions MADE IN USA Revision 111 01.2016 Barranca Diamond Products, Inc. Manual Part No. 167671 1315 Storm Parkway Torrance, CA 90501 Caution: Read all safety and operating Toll-Free: (800) 630-7682 instructions before using this equipment.

  • Page 2: Table Of Contents

    Operated correctly, your HP14 Slab Saw should provide you with years of quality service. In order to help you, we have included this owner’s manual. This owner’s manual contains information necessary to operate and maintain your HP14 Slab Saw safely and correctly.

  • Page 3: Safety Precautions

    HP14 SAFETY SAFETY PRECAUTIONS Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. In order to prevent injury, the...
  • Page 4 HP14 SAFETY REDUCE THE RISK OF UNINTENTIONAL STARTS Make sure the ON/OFF switch is in the OFF position before plugging in a power tool. ROTATING OR MOVING PARTS Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the motor with covers, shrouds or guards removed.
  • Page 5 HP14 SAFETY DIRECTION OF FEED Always feed work into a blade or cutter in the direction shown in this manual. All blades, grinding wheels or polishing belts should always be installed such that rotation is in the direction of the arrow imprinted on the blade, wheel or belt.

  • Page 6: California Proposition 65 Warning

    HP14 SAFETY SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.

  • Page 7: Electrical Requirements & Grounding Instructions

    HP14 SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock.

  • Page 8: Electrical Requirements & Grounding Instructions

    HP14 SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS (continued) To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wall- mounted receptacle. This will prevent water from dripping onto the receptacle or plug. A "drip loop," shown in Figure 2, should be arranged by the user to properly position the power cord relative to the power source.

  • Page 9: Product Specifications

    PRE-START INSPECTION & SET UP After removing your HP14 Slab Saw from the shipping crate, place the saw on a flat surface such as a secure bench top or table, or optional stand (part # 166153).

  • Page 10: Oil/Coolant

    HP14 OIL/COOLANT RECOMMENDED CUTTING OILS Never run a diamond blade dry as this can immediately damage your blade. Use one of the oils/coolants recommended below. Coolant should be kept clean and below 100° F. Sludge should be removed periodically and replaced with fresh coolant so that your cuts will be clean and your blades will not be damaged.

  • Page 11: Setup

    The 301 Supreme notched rim or 303 Professional continuous lapidary diamond blade is manufactured to cut in either a petroleum, mineral, or synthetic oil. Water or water based coolants never should be used in the HP14 saw tank under any circumstances as the steel arbor shaft, cast iron vise and carriage/jaw can severely rust in addition to poor sawing performance, frequent blade dulling, short blade life as well.
  • Page 12 HP14 SETUP The HP14 Slab Saw uses a clutch engagement system, the clutch handle raises (engages at the 3 o'clock position) and lowers (disengages at the 12 o'clock lever position) the threaded (3/8-24) bronze clutch block against the 3/8-24 threaded LH (left hand) rod which is turned by the power feed motor.

  • Page 13: Clutch Adjustment

    CLUTCH ADJUSTMENT CLUTCH ADJUSTMENT AND REPLACEMENT The HP14 Slab Saw uses a friction clutch block (bronze 1/2 threaded) and stainless steel threaded drive screw rod engagement-disengagement system to propel the cast iron carriage/vise. The clutch is comprised of a lower carriage mounted bronze half threaded (3/8-24) fine left hand threaded block and an upper brass non- threaded block with adjusting set screws and a center mounting screw.

  • Page 14: Maintenance

    LUBRICATING OIL REPLACEMENT The HP14 Slab Saw requires periodic routine maintenance to remove and discard properly the build up of rock mud "sludge" and dirty lubricating fluid (oil) from the oil reservoir pan. It will be apparent to the user from the...
  • Page 15 V-BELT MAINTENANCE The HP14 Slab Saw blade arbor is powered by a v-belt from the motor attached to the rear of the oil reservoir. The belt tension should be checked periodically. Belt tension should be such that 1/2" of deflection is measured by finger touch.
  • Page 16 DIAMOND BLADE MAINTENANCE Periodically, the diamond blade on the HP14 Slab Saw will need to be resharpened, should slow or poor saw- ing performance occur. Dull or "glazed over" diamond cutting segment or kerf will either not cut thus stalling the saw, or overheat and shut off the motor.

  • Page 17: Service And Warranty

    NOTES...
  • Page 18 HP14 EXPLODED VIEW Part# 8302014...
  • Page 19 165508 WELDMENT, ON/OFF LEVER 165511 KNOB, 1-1/4" BALL 1/4-20 THREAD 165514 MOUNT, MOTOR 165560 BD-301 14 x 065 x 1 GEMKING 166070 SHAFT, BLADE 166133 ASSEMBLY, FEED MOTOR 166147 HEx CAP SCREW 1/4 - 20 x 5 - 1/2" 166262...
  • Page 20 HP14 EXPLODED VIEW Part# 8302014...
  • Page 21 HP14 PART LISTS Item Part Description Part# Quantity NUT, 5/16-18 HEx 101196 WASHER, FLAT, SAE, 1/4 151915 SCREW, 1/4-20 x 1/2 HEx HEAD 152608 TAG, SERIAL NUMBER, BLANK 157500-RW SCREW, DRIVE, RND HD, #7 x 5/16 157849 BELT, Ax44 161418...
  • Page 22 HP14 EXPLODED VIEW Part# 165507...
  • Page 23 HP14 PART LISTS Item Part Description Part# Quantity WASHER, 5/16 FLAT, USS, 3/8 101360 SCREW, 5/16-18 x 1-3/4 HEx HEAD CAP 150919 WASHER, FLAT, SAE, 5/16 151754 NUT, 1/4-20 HEx 151893 WASHER, 1/4 SAE FLAT 151915 SCREW, SET CUP PT 1/4-20 x 1/4...
  • Page 24 HP14 EXPLODED VIEW Part# 165508...
  • Page 25 HP14 PART LISTS Item Part Description Part# Quantity NUT, 3/8-16 HEx 101188 SCREW, 3/8-16 x 1-1/4 HEx HEAD CAP 150774 WASHER, 3/8 SAE FLAT 150923 SCREW, HEx HD, 1/4 - 20 x 3/4 152370 SCREW, FLAT HD, #10 32 x 1/2 154541 BEARING, BALL 1/2"...

  • Page 26: Exploded View & Parts List

    HP14 EXPLODED VIEW & PARTS LIST Part# 166147 WIRING DIAGRAM WIRING DIAGRAM DRIVE SCREW DRIVE SCREW MOTOR MOTOR SCALE 0.500 Y(4) SCALE 0.500 B(5) Y(4) BL(1) BLADESHAFT MOTOR B(5) LINE PLUG BL(1) BLADESHAFT MOTOR LINE PLUG Item Part Description Part#...

  • Page 27: Exploded View & Parts List

    HP14 EXPLODED VIEW & PARTS LIST Part# 165510 Item Part Description Part# Quantity WASHER, FLAT, SAE, 1/4 151915 SCREW, HEx HD 1/4 - 20 x 2 158282 SCREW, SOC HD CAP, 1/4 - 20 x 1 - 1/4 159336 NUT, HEx, NYLK, 1/4 - 20...

  • Page 28: Part Number

    HP14 WARRANTY BARRANCA DIAMOND LIMITED WARRANTY Please complete the warranty registration card and return. Any problems encountered should be directed to Barranca Diamond Customer Service department at (800) 630-7682 M-F 8am - 5pm PST. NOTE THIS INFORMATION FOR FUTURE USE:...
  • Page 29 HP14 WARRANTY SPECIFICS APPLICABLE TO LIMITED WARRANTY OF DIAMOND BLADES AND CORE BITS Laser Welded Blade and Bit Warranty If the laser weld between the segment and the steel core or barrel fails during normal use, the blade or bit will be replaced free of charge.
  • Page 30 HP14 WARRANTY REPLACEMENT PARTS Replacement parts for this tool may be ordered form your Barranca Diamond distributor or directly from Barranca Diamond. Please have the following information ready before calling: • Model and serial number of the machine • Date of purchase •...
  • Page 31 NOTES...
  • Page 32 1315 Storm Parkway Torrance, CA 90501 Phone: (310) 523-5867 Toll Free: (800) 630-7682 Fax: (310) 257-3063 www.barrancadiamond.com...

Table of Contents