Related Manuals for Necchi Vigorelli S1
Summary of Contents for Necchi Vigorelli S1
- Page 1 Covering Vigorelli S1, M220, M223, M226 Note: Some items covered in this manual are optional extras or accessories and may not be included with your machine...
-
Page 2: Safety Instructions
Safety instructions Warning against injuries and material damages: Like any other electrical device, a sewing machine can cause serious, even life-threatening injuries.To According to legislation, you as the user of an avoid this, and in order to work safely: electrical appliance are responsible for preventing possible accidents through safety-conscious •... -
Page 3: Before Use
Before use Be sure to read this section before use 1. Important safety instructions These safety instructions are designed to prevent danger or damage arising from the incorrect operation of the machine. Read carefully and always follow the instructions. Explanation of " WARNING "... - Page 4 CAUTION When the machine is not in use it should be stored safely, not on the floor as protruding parts could cause injury if a person fell on the machine. Not doing so could cause an injury. Use with the shuttle cover closed. Not doing so could cause an injury.
-
Page 5: How To Change The Power Plug
Do not operate on an unstable surface such as a sofa or a bed. If the sewing machine falls down, it could cause an injury or damages to the machine. Do not drop or insert any foreign objects into any openings such as opening space when you remove the face cover and / or the outer casing space of bobbin case. -
Page 6: Table Of Contents
CONTENTS Name of parts .................... 6-7 Accessories....................8 Before sewing (Power supply and sewing lamp).......... 9 Removing extension table................10 Free-arm sewing ..................10 Winding the bobbin ..................11 Removing bobbin case and bobbin ............. 12 Inserting bobbin into bobbin case ..............13 Inserting bobbin case into shuttle race ............ -
Page 7: Name Of Parts
NAME OF PARTS (FRONT VIEW) 1. Thread tension dial 2. Pattern selector dial 3. Bobbin winder stopper 4. Stitch length dial 5. Reverse button 6. Thread guide and needle clamp 7. Needle threader 8. Threading lever 9. Shuttle cover 10. Extension table 11. - Page 8 NAME OF PARTS (REAR VIEW) 1. Presser foot lever 2. Thumb screw 3. Needle plate 4. Handle 5. Spool pin (B) 6. Clutch button 7. Hand wheel 8. Spool pin (A) 9. Bobbin winder spindle - 7 -...
-
Page 9: Accessories
ACCESSORIES Bobbin Zigzag foot Felt Buttonhole foot (on machine) Zipper foot Screw driver Spool pin (B) Spool pin (A) Needle Needle plate Darning plate Buttonhole cutter screw driver - 8 -... -
Page 10: Before Sewing (Power Supply And Sewing Lamp)
BEFORE SEWING 1. Fit plug into the machine. Power supply / Power supply plug 2. Insert plug into the main socket. 3. Sewing speed can be varied by the foot Power supply control. If the supply cord that fixed with foot controller is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a... -
Page 11: Removing Extension Table
REMOVING EXTENSION TABLE Hold the left end of the table and pull it out in direction of the arrow. FREE-ARM SEWING 1. This sewing machine can be used as a flat bed machine but easily converts to a free arm machine by removing the extension table. -
Page 12: Winding The Bobbin
WINDING THE BOBBIN 1. Release by pushing clutch button to bobbin and lock by pushing it to needle. 2. Push bobbin winder from left to right, then it starts winding. 3. Push bobbin winder from right to left and move clutch button to needle sign, then it starts sewing. -
Page 13: Removing Bobbin Case And Bobbin
REMOVING BOBBIN CASE AND BOBBIN 1. Raise the needle to its highest position and open shuttle race cover. 2. Open the hinged latch of the bobbin case and pull the bobbin case out of the machine. Hinged latch 3. Release the latch and the bobbin will fall out easily. -
Page 14: Inserting Bobbin Into Bobbin Case
INSERTING BOBBIN INTO BOBBIN CASE 1. Pull 5 cm of thread from bobbin and insert it into bobbin case as shown. 5 cm 2. Guide the end of thread into the slot. Slot 3. Pull the thread through the slot and Tension spring under the tension spring and draw out about 10 cm of thread. -
Page 15: Inserting Bobbin Case Into Shuttle Race
INSERTING BOBBIN CASE INTO SHUTTLE RACE 1. Raise the needle to its highest position. Finger Pull the thread to the front, open the latch of the bobbin case and hold it. Hinged latch 2. Holding the latch open, place bobbin case onto the centre pin in the shuttle Insert and release latch. -
Page 16: Threading Upper Thread & Twin Needle Threading
THREADING UPPER THREAD Warning: Before contriving please adjust main control switch to (O). Pass the thread from A to H as shown. Twin needle threading. For auto threaded system see Page 16. - 15 -... -
Page 17: Automatic Needle Threader
AUTOMATIC NEEDLE THREADER NOTE: * Needle must be in its highest position. * Needle threader cannot be used with a twin needle. 1. Raise the needle to its highest position. Lower the needle threader lever as far as it will go. 2. -
Page 18: Drawing Up The Bobbin Thread
DRAWING UP THE BOBBIN THREAD 1. Hold the upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes up. Then stop the hand wheel when the take up lever is at its highest position. -
Page 19: Levelling The Machine
LEVELLING THE MACHINE Down - 18 -... -
Page 20: Adjusting Thread Tension
ADJUSTING THREAD TENSION Normal upper thread tension: 3 – 5 Correct Upper thread Fabric Upper thread tension may be adjusted by Bobbin thread turning the thread tension dial. Incorrect Inside of fabric Upper thread Lower thread tension can be increased by turning the screw of the bobbin case slightly to the right (clockwise). -
Page 21: Changing Needle
CHANGING NEEDLE Warning: Before changing the pin please Needle clamp screw adjust main control switch to (O). 1. Raise the needle bar to its highest Tighten position. 2. Loosen needle clamp screw and remove the old needle. 3. With the flat side of the needle facing away from you, insert the needle as far up as it will go. -
Page 22: Fabric-Thread-Needle-Table
FABRIC-THREAD-NEEDLE-TABLE Please pay attention to the following list as a guide for sewing different types of fabric. Indication of Fabric Thread Needle Length of Stitches Upper Tension Straight stitch Stitch Length Dial Nylon 80 Cotton HA × 1 Light No. 11 Tricot 60 S Fiber silk... -
Page 23: Sewing (Pattern Selector) And Operation Table
SEWING (PATTERN SELECTOR) AND OPERATION TABLE Twin needle Stitch Presser Darning Stitch patterns stitch patterns length foot plate Straight stitch Zigzag Blind stitch Box stitch Three step zigzag stitch Double overlock stitch Pullover stitch Honeycomb stitch Zigzag stitch Straight stretch stitch Automatic Embroidery... -
Page 24: To Start Sewing
TO START SEWING Important hints: 1. Raise the take-up lever to its highest position before starting and after stopping sewing. 2. Hold both threads about 10 cms to the rear of the machine for the first two or three stitches. 3. -
Page 25: How To Finish Stitches
HOW TO FINISH STITCHES 1. Sew to the edge of seam. 2. Push the reverse button and sew in reverse for about 3-4 cms. 3. Raise needle into its highest position. 4. Lift the presser foot and pull the fabric out of the back of the machine. -
Page 26: Straight Stitch
STRAIGHT STITCH 1. This type of stitching is used most frequently. 2. The zigzag presser foot can be used for both straight and zigzag sewing. 3. For sewing light fabric, use a smaller stitch size. (Refer to page 21 for dial setting). ZIGZAG SEWING Pattern selector position Satin stitching can be used for sewing... -
Page 27: Overcasting
OVERCASTING Use these stitches for oversewing rough edges. STRAIGHT AND ZIGZAG STRETCH STITCHES Use this stitch with knitted, tricot or other stretchy fabrics. The stitch enables your seam to stretch without breaking the thread. - 26 -... -
Page 28: Blind Stitch
BLIND STITCH 1. Fold fabric as shown. 2. Finish the seam as shown. - 27 -... - Page 29 Adjust the width to obtain the correct seam. Wrong: Needle is not piercing edge to fold at all. Needle pierces the edge of fold too much. Correct seam. - 28 -...
-
Page 30: Button Sewing
BUTTON SEWING (Optional) Utilise the foot of sewing of buttons. (Use Darning plate see page 20) 1. Place the darning plate properly. 2. Place button presser foot in position and attach it firmly. 3. Place the button between presser foot and fabric and lower the presser foot. -
Page 31: Zipper Sewing
ZIPPER SEWING Utilise the foot of closing zipper. Select straight stitch. 1. Zipper foot is designed to sew close to a raised edge, thus preventing sewing on zipper. 2. Place zipper foot in position and attach firmly. 3. Fold the fabric about 2 cm and place the fabric under foot. -
Page 32: Buttonhole Sewing
BUTTONHOLE SEWING Utilise the foot of the buttonholes. Set the stitch length dial. Pattern selector dial Steps Settings 1. Set dial to “1“ position 2. Sew left side 3. Raise the needle 4. Set dial to “2“ position 5. Sew 5-6 stitches 6. -
Page 33: Hemming
HEMMING (Optional) 3 mm 1. Raise the foot and the needle to its highest position. Replace the foot with the picot foot. 2. Fold over the fabric edge by about 3 mm 1 mm and place it under the foot. Secure the folded edge with a few stitches. -
Page 34: Embroidery
EMBROIDERY (Use Darning plate see page 20) Remove the presser foot and attach the feed cover plate. Lower feed dog and move the hooped fabric slowly in the desired direction until the fabric has been embroidered. QUILTER GUIDE (Optional) 1. Slide the arm through the hole on top of the pressure foot holder. -
Page 35: Maintenance (Cleaning And Oiling)
MAINTENANCE Warning: Please always unplug the power plug before you change the bulb or perform maintenance work to the machine so that you prevent deadly peril and electric shock. 1. Raise needle to its highest position. 2. Take out the bobbin case. 3. -
Page 36: Checking Performance Problems-Troubleshooting
CHECKING PERFORMANCE PROBLEMS – TROUBLESHOOTING Problem Probable cause What to do Fabric does not - Feed dog down - Raise feed dog move - Stitch length dial in “0“ position - Set dial between 1 and 4 - Incorrect insertion of needle - Re-insert needle - Bent needle - Replace needle...