Table of Contents
Advertisement
Available languages
Available languages
The 565SD microphone is a dual-impedance, unidirectional dynamic microphone with a
strong, wire-mesh, spherical front grille that contains a highly effective wind and "pop" filter.
Shipped connected for low-impedance operation, a 565SD microphone provides excellent
vocal or speech reproduction on stages and studios, and is a popular choice for use in pub-
lic auditoriums, churches, convention halls, and schools.
FEATURES
•
Selectable dual-impedance operation
•
Silent, lockable on/off switch
•
Cardioid dynamic
•
Frequency response: 50 to 15,000 Hz
IMPEDANCE SELECTION
The microphone is shipped connected for low impedance operation. To change to high
impedance proceed as follows:
1.
Loosen plug element by turning slotted setscrew counterclockwise (turn counterclock-
wise to lower screw into plug element). Pull plug element from case. Be careful not to
stretch or break wires.
2.
The low impedence socket of the impedence selection connector is connected to Pin 3
of the plug element. Move the connector to the high-impedance socket (see diagram).
3.
Reinsert plug element and tighten setscrew (turn clockwise to raise screw).
SET SCREW
IMPEDANCE SELECTION
CONNECTOR
Polarity
To test two microphones and their cables for common polarity, connect them to an amplifier
and talk or sing into them while holding them three or four inches apart. The sound from the
speakers should be the same when talking into either microphone or directly between them
if they have common polarity. If the sound level drops drastically, or if a dead spot is found
when talking between the two microphones, either the microphones or their cables have
different polarity. All cables and microphones can be tested in this manner to ensure that
they have common polarity.
To reverse the polarity of a low-impedance microphone cable, use either a Shure A15PRS
Switchable Phase Reverser or interchange the wires connected to pins 2 and 3 of the XLR
connector.
SPECIFICATIONS
Type
Frequency Response
Polar Pattern
Output Impedance
Sensitivity
(at 1 kHz, open circuit
voltage)
Polarity
Weight
Switch
Connector
Case
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC Directive 2004/108/EC. Meets
Harmonized Standards EN55103-1:1996 and EN55103-2:1996, for residential (E1) and
light industrial (E2) environments.
The Declaration of Conformity can be obtained from:
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department EMEA Approval
Wannenacker Str. 28
PLUG ELEMENT
D-74078 Heilbronn, Germany
Phone: +49 7131 72 14 0
Fax: +49 7131 72 14 14
E-Mail: EMEAsupport@shure.de
ACCESSORIES AND PARTS
PIN 3
Furnished Accessories
Swivel Stand Adapter
Replacement Parts
Cartridge
Screen and Grille
Optional Accessories
Line Matching Transformer
Shock Stopper™ Isolation Mount
Dual Mount
Windscreen (6 colors available)
7.6 m (25 ft.) Cable (XLR-XLR)
6.m (20 ft.) Cab; XLR-1/4 in.)
Dynamic (moving coil)
50 to 15,000 Hz
Cardioid
EIA rated at 150Ω (250Ω actual)
L: −56.0 dBV/Pa (1.6 mV)
H: −34.0 dBV/Pa (20 mV)
1 Pascal=94 dB SPL
Positive pressure on diaphragm produces positive voltage
on pin 2 with respect to pin 3
Net: 0.298 kg (0.656 lbs)
On/Off: Lockable ON/OFF switch
Three-pin professional audio (XLR), male
Chrome-plated die casting with steel mesh grille
A25D
R65
RS65
A95 Series
A55M, A55HM
A26M
A58WS
C25J
C20AHZ
Advertisement
Table of Contents
