How to install the monitor hardware .................. 8 Detach the base ......................10 Getting the most from your BenQ monitor ..............11 How to install the monitor on a new computer ............12 How to upgrade the monitor on an existing computer ..........13 How to install on Windows XP systems ..............14...
Getting started When unpacking please check you have the following items. If they are missing or are damaged, please immediately contact the dealer at which you purchased the goods. BenQ LCD Monitor Quick Start Guide CD-ROM Disk Power cord Signal cable...
How to install the monitor hardware Make sure that the computer and monitor’s power are both turned off. Please follow these four steps to install your LCD monitor. 1. Pull the base all the way back. Do not insert your fingers into the seam between base and monitor while installing the display.
Page 9
3. i.> Connect the power cord to your monitor. ii.> Connect the signal cable to your monitor. iii.> Use the velcro strip attached to the signal cable to route the power cord and signal cables together, and then collect the cables neatly in place via the cable bracket. 4.
How do I gain the most benefit from my new monitor? To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
BenQ LCD Monitor is the first ever monitor to be connected to it. If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
The Monitor Properties window will display. If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper drivers are already installed, and you need do nothing further. Cancel out of these property windows.
Page 15
This will close the Display Properties windows. You do not need to restart Windows XP, as the BenQ LCD monitor drivers will operate immediately with no further action required by you. Getting the most from your BenQ monitor...
This will jump you directly to the Upgrade Device Driver Wizard, skipping the next step. 4. In Windows 2000, click the Driver tab and the Update Driver button. The Upgrade Device Driver Wizard will display. How to complete the Windows Upgrade Device Driver Wizard. Getting the most from your BenQ monitor...
The contents of the ‘Driver’ folder will display. 7. Click the Open button. This will return you to the Install from Disk window, and it will have entered the address to the BenQ LCD Monitor CD ‘Driver’ folder into the field titled ‘Copy manufacturer’s files from:’ .
Page 18
Alternatively, Windows ME or 98 will ask you if want to make the changes and reboot or not reboot. You should select the reboot option as this causes Windows to load the new drivers when it next restarts. Getting the most from your BenQ monitor...
Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed. The best possible picture for your FP556s/FP557s is achieved with a resolution of 1024x768. This is called “Native Resolution” or maximal resolution – that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit.
How to adjust the screen refresh rate You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer.
If you wish to, you can always adjust the screen settings manually using the buttons on the monitor panel. To assist you in this endeavour, BenQ has provided a screen test image utility which you can use to check for screen color, grayscale and line gradient display.
How to adjust the monitor A Look at the Control Panel This topic describes how to adjust your BenQ LCD monitor using the push button (keys) on the monitor’s edge, to access the monitor properties using the On-Screen Display (OSD).
Hot Key Mode Brightness and Contrast hot keys Press the key to enter the Brightness menu. Press the keys to adjust the degree of Brightness. Then press the Exit key to exit the OSD. Press the key to enter the Contrast menu. Press the keys to adjust the degree of Contrast.
Main Menu Mode Control Functions Available in Main Menu Main Menu Luminance sub menu Press the keys to adjust the degree of Brightness. Press the Exit key to return to previous menu. Press the keys to adjust the degree of Contrast.
Page 25
Geometry sub menu Press the keys to adjust the display Horizontal Position. Press the Exit key to return to previous menu. Press the key to adjust the display Vertical Position. Press the Exit key to return to previous menu. Press the keys to adjust the monitor Pixel Clock.
Page 26
Color sub menu User Preset: Press the keys to adjust the degree of screen color balance for Red, Green and Blue. Press the Exit key to return to previous menu. Press the keys to adjust the degree of Red. Press the keys to adjust the degree of Green.
Page 27
OSD sub menu On-Screen Display (OSD) Press key to adjust the Horizontal Position of the OSD. Press the Exit key to return to previous menu. Press the keys to adjust the Vertical Position of the OSD. Press the Exit key to return to previous menu. Press the keys to adjust the display time of the OSD.
Page 28
Languages Sub menu How to adjust the monitor...
Page 29
Recall sub menu Press the keys to select Color Recall. Press the Enter key to recall color settings, or press the Exit key to return to previous menu. Press the keys to select Recall All. Press the Enter key to recall position and color settings, or press the Exit key to return to previous menu..
Page 30
Miscellaneous sub menu Sharpness: Press the keys to adjust the degree of Sharpness. Press the Exit key to return to previous menu. Display Information: Select Display Information to display the current monitor proerty settings. Press the Exit key to return to previous menu. How to adjust the monitor...
Troubleshooting Frequently Asked Questions (FAQ) The image is blurred: Read the How to adjust the screen resolution section, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test.
How to adjust the screen resolution section and then select the correct resolution, refresh rate and make adjustments based on these instructions. Need More Help? If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: Support@BenQ.com Troubleshooting...