Makita BUR141 Instruction Manual page 7

9. Remove sand, stones, nails etc. found within
the working range. Foreign particles may
damage the cutting tool and can cause to be
thrown away, resulting in a serious injury.
10. Should the cutting tool hit stones or other
hard objects, immediately switch off the motor
and inspect the cutting tool.
11. Before commencing cutting, the cutting tool
must have reached full working speed.
12. During operation always hold the tool with
both hands. Never hold the tool with one hand
during use. Always ensure a safe footing.
13. All protective equipment such as guards and
the shoulder strap supplied with the tool must
be used during operation.
14. Except in case of emergency, never drop or
cast the tool to the ground or this may
severely damage the tool.
15. Never drag the tool on the ground when
moving from place to place, the tool may
become damaged if moved in this manner.
16. Always remove the battery cartridge from the
tool:
− whenever leaving the tool unattended;
− before clearing a blockage;
− before checking, cleaning or working on
the tool;
− before making any adjustments, changing
accessories or storing;
− whenever
unusually.
17. To cut thick materials, such as weed, high
grass, bushes, shrubs, underwood, thicket etc.
(max. 2 cm dia. thickness), perform the cutting
work by swinging the tool evenly in half-circles
from right to left (similar to using a scythe).
18. Don't force the tool. it will do the job better
and with less likelihood of a risk of injury at
the rate for which it was designed.
Maintenance instructions
1. The condition of the cutting tool, protective
devices and shoulder strap must be checked
before commencing work.
2. Turn off the motor and remove the battery
cartridge before carrying out maintenance,
replacing the cutting tool and cleaning the tool.
3. After use, disconnect the battery cartridge
from the tool and check for damage.
4. Check for loose fasteners and damaged parts
such as nearly cut-off state halfway in the
cutting tool.
5. When not in use store the equipment in a dry
location that is locked up or out of children's
reach.
6. Use only the manufacturer's recommended
replacement parts and accessories.
the tool starts vibrating
7. Never use replacement parts or accessories
not provided
manufacturer.
8. Always ensure that ventilation openings are
kept clear of debris.
9. Inspect and maintain the tool regularly,
especially before/after use. Have the tool
repaired only by our authorized service center.
10. Keep handles dry, clean and free from oil and
grease.
11. When not in use store the machine out of the
reach of children.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
7
or recommended by the
ENC007-7