Specifications - Bosch WEU PMF 190 E Original Instructions Manual

OBJ_BUCH-345-009.book Page 13 Friday, April 12, 2013 11:38 AM
 Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can
lead to injuries.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Wear protective gloves when changing application
tools/accessories. Application tools/accessories become
hot after prolonged usage.
 Do not scrape wetted materials (e.g. wallpaper) or on
moist surfaces. Penetration of water into the machine in-
creases the risk of an electric shock.
 Do not treat the surface to be worked with solvent-con-
taining fluids. Materials being warmed up by the scraping
can cause toxic vapours to develop.
 Use extreme caution when handling blades and scrap-
ers. The application tools are very sharp. Danger of injury.
 Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Product Description and

Specifications

Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e.g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.
Bosch Power Tools
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Thumbwheel for orbit frequency preselection
3 Venting slots
4 Handle (insulated gripping surface)
5 Tool holder
6 Plunge saw blade
7 Clamping bolt with washer
8 Allen key
9 Sanding plate
10 Sanding sheet
11 Depth stop
12 Segment saw blade
13 Vacuum hose*
14 Vacuum connection*
15 Fastening screw of the dust extraction*
16 Dust extraction*
17 Felt ring of the dust extraction*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Multi-function tool
Article number
Preselection of orbital stroke rate
Rated power input
Output power
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Sanding: a =3.5 m/s , K=1.5 m/s
h
Cutting with plunge cut saw blade: a
2
K=1.5 m/s
Cutting with segmental saw blade: a
2
Scraping: a =12 m/s , K=1.5 m/s
h
English | 13
PMF 190 E
3 603 A00 5..

W 190
W 89
-1
min 15000 –21000
° 1.4
kg 1.2
/II
2
2
=12.5 m/s ,
h
2 2
=14 m/s , K=2.5 m/s
h
2
.
2 609 007 126 | (12.4.13)