Subscribe to Our Youtube Channel
Related Manuals for Mhouse GD1
Summary of Contents for Mhouse GD1
- Page 1 MhouseKit GD1 - GD10 For the automation of a sectional or up-and-over door. Installation instructions and warnings...
-
Page 2: Table Of Contents
You are therefore invited to read this manual carefully. via Pezza Alta, 13, ZI 31046 Oderzo Tel: 0422 202109 MHOUSE, in order to improve its products, reserves the right to modify Fax: 0422 852582 them at any time without prior notice. In any case, the manufacturer email: info@mhouse.biz... -
Page 3: Warnings
Directive if used in the configurations foreseen in this instructions manu- intended application, do not proceed with the installation. al and in combination with the articles present in the Mhouse S.r.l. prod- uct catalogue. If the product is not used in configurations or is used with •... -
Page 4: Product Description
3x1m 4x1m 2.2 Description of the automation To clarify a few terms and aspects of a sectional or up-and-over door automation system: In Figure 1 we provide an example of a typical GD1 and GD10 application: Figure 1 [A] FL1 flashing light with incorporated aerial (optional) -
Page 5: Description Of Devices
FL1 flashing light with incorporated aerial. FL1 flashing light with incorporated aerial. * The screws required for mounting GD1 and GD10 are not supplied as they depend on the type of material and its thickness. 2.3.1 GD1K and GD10K Electromechanical Gearmotor GD1K and GD10K are electromechanical gearmotors made up of a 24Vdc motor. -
Page 6: Ph1 Photocells (Optional)
4 types of command to a single automation unit, or to control up to 4 different automation units. The transmission of the command is confirmed by the LED [A]; an eye- let [B] allows them to be hung on a keyring. Figure 7 6 Instructions GD1-GD10... -
Page 7: Installation
“WARNINGS”. 3.1 Preliminary checks The GD1 and GD10 must not be used to power a door that is not • The gearmotor should be mounted so that it coincides with the efficient and safe and cannot solve defects resulting from incor- centre of the door, or is slightly off-centre, e.g. -
Page 8: Operating Limits
In general the GD1 and GD10 are suitable for the automation of section- istics chart for the GD gearmotor. -
Page 9: List Of Cables
3 mm, which allows the power sup- • Have a suitably protected 16A “schuko” outlet installed, where ply to be disconnected during the installation and maintenance of you can plug in GD. the GD. Instructions GD1-GD10 9... -
Page 10: Installation Of The Various Devices
Depending on the model, the installation of the GD is comprised of the following parts: - Assembly of the guide supplied with GD1 (see paragraph 3.3.1) - Assembly of the guide supplied with GD10 (see paragraph 3.3.2) - Fixing of the gearmotor to the guide (see paragraph 3.3.3) - Fixing of the gearmotor to the ceiling (see paragraph 3.3.4) -
Page 11: Assembly Of The Guide Supplied With Gd10
Figure 24 8 Tension the belt by means of the M8 nut [D] (figure 25) until it is suffi- ciently taut. Figure 20 Figure 21 Figure 25 Instructions GD1-GD10 11... - Page 12 Figure 29 4 Return the belt tensioner device and carriage to the initial position. Assemble the guide head section [A], as shown in figure 30. This requires a certain force; if necessary use a rubber mallet. Figure 30 12 Instructions GD1-GD10...
-
Page 13: Fixing Of The Gearmotor To The Guide
Position B Figure 39 6 Make sure that the guide is perfectly horizontal, then cut the excess of the brackets using a hacksaw. Figure 37 Figure 40 Instructions GD1-GD10 13... - Page 14 9 Loosen the screws in the two mechanical stops, then place the front mechanical stop [O] before the carriage (Figure 43). Push the carriage hard in the closing direction and, in the reached posi- tion, tighten the screw firmly [P]. Figure 43 14 Instructions GD1-GD10...
-
Page 15: Photocells (Optional)
Figure 50 5 Drill the holes in the wall using a hammer drill with a 5 mm bit and insert the 5 mm screw anchors. Instructions GD1-GD10 15... -
Page 16: Fl1 Flashing Light (Optional)
4 Breach the four holes for the screws and the hole for the passage of the cables in the bottom or side, depending on the installation position, using a screwdriver. Figure 61 Figure 57 16 Instructions GD1-GD10... -
Page 17: Electrical Connections To The Control Unit
66; make the connections and then reinsert them. 4 When the connections have been completed secure the cables using suitable clamps. 5 To close the cover, rotate it and push until you hear a click. Tighten screw [A]. Figure 64 Figure 66 Figure 65 Instructions GD1-GD10 17... -
Page 18: Power Supply Connection
5.5 “Troubleshooting”. The connected devices recognition stage can be repeated again at any time, even after the installation (for example, if an additional photocell is installed); just repeat the procedure starting from step 1. Figure 71 18 Instructions GD1-GD10... -
Page 19: Learning Of The Door's Open And Closed Positions
The transmitter supplied has already been memorized and when you press the buttons the following commands are transmitted: Button T1 “OPEN” command Button T2 “Open partially” command Button T3 “Open only” command Figure 75 Button T4 “Close only” command Instructions GD1-GD10 19... -
Page 20: Regulations
20 Kg, fixed in the middle of the 700x300x200mm test parallelepiped with 3 black sides and 3 polished doors lower edge. white or mirrored sides, according to the EN 12445 standard. 20 Instructions GD1-GD10... -
Page 21: Commissioning
4 Remove the electronic boards. ulations locally in force. 5 Sort the various electrical and recyclable materials and consign them to licensed firms for recovery and disposal. 6 Consign the remaining materials to authorized scrap collection centres. Figure 80 Instructions GD1-GD10 21... -
Page 22: Additional Information
• If the “motor force” control is used to assist the impact force reduction system, measure the force again after each adjustment in compliance with EN standard 12445. • The weather conditions may affect the movement of the door, therefore periodic re-adjustments may be necessary. Figure 81 22 Instructions GD1-GD10... -
Page 23: Checking The Adjustments With The Radio Transmitter
For information on the new accessories, refer to the MHOUSE catalogue or PT50: Pair of 500 mm posts with one photocell on each. visit the site www.mhouse.biz. -
Page 24: Recognition Of Other Devices
WARNING: in the GD1 version the ECSBus output has a maximum load of 1 unit (with A type addresses only) in the GD10 version it has a maximum load of 6 units; a pair of photocells absorbs power equal to 1 ECSBUS unit... -
Page 25: Memorization Of Radio Transmitters
NEW transmitter to which you wish to associate that unit and will assume the characteristics of the OLD one. command. If there are other transmitters to be memorized, repeat all the steps above for each new transmitter. Instructions GD1-GD10 25... -
Page 26: Deleting A Radio Transmitter
The manoeuvre is carried out but the • Replace the lamp with one having the same characteristics. courtesy light does not work. Figure 87 26 Instructions GD1-GD10... -
Page 27: Diagnostics And Signals
1 second’s pause Activation of the “motor force” limiting device identify the cause 3 flashes 4 flashes During the movement the STOP input was activated; identify 1 second’s pause Activation of the STOP input the cause 4 flashes Instructions GD1-GD10 27... -
Page 28: Control Unit
Complete cyclic operation Repeat the procedure (see paragraph 3.5.2. “learning the door’s open and 1 flash every second the positions have not been acquired. closed positions”) 2 flashes every second position learning procedure in progress Figure 89 28 Instructions GD1-GD10... -
Page 29: Technical Characteristics
6 Technical characteristics GD is produced by NICE S.p.a. (TV) I, MHOUSE S.r.l. is an affiliate of the NICE S.p.a. group. Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. - Page 30 Security lock Key with 450 different key The device can only be connected to the “OPEN” and “STOP” terminals on the MHOUSE automation control Power supply/contacts units, to which it sends the control signals and by which it is energized for night illumination Operating ambient temperature -20 ÷...
- Page 31 Operating ambient temperature -20 ÷ 50°C Use in acid, saline or potentially explosive atmosphere Protection class IP40 (suitable for use indoors or in protected environments) Dimensions / weight 72 x 31 h 11mm / 18g Instructions GD1-GD10 31...
-
Page 32: Annexes
CE Declaration of Conformity to be filled in and delivered to the owner of the power operated Sectional or Up-and-over Door. 7.3 Annexe 3: Operating Guide Brief guide to be used as an example for drafting the operating guide to be delivered to the owner of the power operated sectional or up-and-over door. 32 Instructions GD1-GD10... -
Page 33: Allegato 1: Ce Declaration Of Conformity Of Gd Components
Conformity Declaration CE Declaration of Conformity according to the directives98/37/CE, 73/23/CEE, 89/336/CEE and 1999/5/CEGD1 and GD10 are produced by NICE S.p.a. (TV) I, MHOUSE S.r.l. is an affiliate of the NICE S.p.a. group. Number: 171/GD1/GB Date: 02/02/2005 Revision: 01 The undersigned Lauro Buoro, managing director, declares under his sole responsibility that the following product: Manufacturer’s name:... -
Page 35: Annexe 2: Ce Declaration Of Conformity Of Power Operated Sectional Or Up-And-Over Door
Declaration of Conformity According to Directive 98/37/EEC, ANNEXE II, part A (CE declaration of conformity for machines) The undersigned / Company (name or business name of person who has put the power operated sectional or up-and-over door into service) (address) Declares under his/her sole responsibility that: The automation : power operated sectional or up-and-over door... -
Page 37: Annexe 3. Operating Guide
If the safety devices are out of order the automation must be repaired as soon as possible. Figure 91 Instructions GD1-GD10 37... -
Page 38: Maintenance Operations To Be Performed By The User
2 Push the lamp up and rotate to remove. Insert a new 12V / 21W lamp with BA15 socket. 1 Aprire il coperchio svitando la vite [A] e premendo il bottone [B]. Figure 96 Figure 97 Figure 98 38 Instructions GD1-GD10... - Page 40 Mhouse Via Pezza Alta, 13 - Z.I. Rustignè 31046 Oderzo TV Italia Tel. +39 0422 20 21 09 Fax +39 0422 85 25 82 info@mhouse.biz www.mhouse.biz...
Need help?
Do you have a question about the GD1 and is the answer not in the manual?
Questions and answers