Related Manuals for Taurus 24VACH
Summary of Contents for Taurus 24VACH
- Page 1 24V Lithium-ion CordLess driLL INSTRUCTIoN MANUAl Model NUMBeR: 24VACH AFTeR SAleS SUPPoRT Tel: 1800 909 909 eMAIl: info@globalpowerbrands.com...
-
Page 2: Table Of Contents
CONTENTS Congratulations on choosing to buy a TAURUS ® TITANIUM product. All products brought to you by TAURUS TITANIUM are ® manufactured to the highest standards of performance and safety, and, as a part of our philosophy of customer service... -
Page 3: Introduction
Description of symbols Introduction The rating plate on your tool may show symbols. Your new drill power tool will more than satisfy These represent important information about the your expectations. It has been manufactured under stringent drill Quality Standards to meet superior product or instructions on its use. -
Page 4: Specifications
Specifications General safety instructions for handling power tools Motor: 24 V– . .. WARNING. Read all safety warnings and Low speed: -Lo = 0 – 400min all instructions. High speed: -Hi = 0 – 1100 min Failure to follow the warnings and instructions may result in Drill diam Ø: - Wood 28 mm electric shock, fire and/or serious injury. - Page 5 c. Do not expose power tools to rain or wet conditions. e. Do not overreach. Keep proper footing and balance Water entering a power tool will increase the risk of at all times. This enables better control of the power tool electric shock.
- Page 6 f. Keep cutting tools sharp and clean. Properly Service maintained cutting tools with sharp cutting edges are less a. Have your power tool serviced by a qualified repair likely to bind and are easier to control. person using only identical replacement parts. This g.
- Page 7 g. Fluid can escape from the battery when used f) Do not grasp the tool or place your hands too close to the incorrectly. Avoid all contact with this. In the event of spinning chuck or drill bit. Your hand may be lacerated. accidental contact, rinse with water.
-
Page 8: Accessories
Accessories Additional safety instructions for the charger and batteries We recommend that you purchase genuine accessories or a) Use only the charger and batteries supplied in this pack. replacement parts. Please contact our After sales hotline on 1800 909 909 or via email: info@globalpowerbrand.com b) Protect the charger and battery pack against moisture including rain and high humidity. - Page 9 Safety notes for battery/charger • Keep the charger away from rain or damp conditions. Water entering into the charger will increase the risk of an electrical shock. Keep the charger clean. Contamination will increase • the risk of an electrical shock. Check the charger, cable and plug each time you •...
-
Page 10: Know Your Product
Know your product This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. The machine is intended only for use in household. All other applications are expressly ruled out. 1. -
Page 11: Important Information - Product Care
Important information – Product care These safety devices have been fitted for the safety, reliability and life of the tool. This drill/driver uses Lithium Ion Battery Cells. Care Fitting and removing MUST be taken to ensure both the safety and life of the pack is maintained. -
Page 12: Battery Charging
Battery charging IMPORTANT. Before attempting to charge the battery, check the charger and the battery to ensure the charging equipment matches the battery supplied. The components are all labelled with component numbers. CAUTION! The rechargeable battery is not fully charged on leaving the factory. -
Page 13: Speed Gearbox, Using The Drill
2 Speed gearbox CAUTION. Extended use of the variable speed under load will overload and then permanently damage the The 2 Speed Gearbox allows you HIGH speed control. to select a gear with the optimum Drill Overload speed and torque to suit the application. -
Page 14: Low Voltage Cut Out
Low voltage cut out Controlling the torque allows for better control when using the drill on specific add screwing tasks and prevents over- The battery pack used on this tool is fitted with a low fastening and over-tightening. voltage cut out feature within the circuitry. For drilling, always use the Drill position by aligning the Drill The low voltage cut out feature operates when the voltage symbol with the triangular indicator on the front face of the... -
Page 15: Drilling
Drilling LED work light Drilling metals When the unit is switched on, the LED work light (9) also comes on to ensure better vision and to make working in • Always clamp sheet metal. dark areas more safe. The working light goes out when the •... -
Page 16: Maintenance And Environmental Protection
0°C or rise above 40°C. email: info@globalpowerbrands.com CAUTION! Electrical and battery operated units that no All products brought to you by TAURUS TITANIUM are ® longer work should not be disposed of in the household manufactured to the highest standards of performance and... - Page 17 After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com...
- Page 18 After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com...
- Page 19 After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com...
- Page 20 After Sales Support TEL: 1800 909 909 EMAIL: info@globalpowerbrands.com...
Need help?
Do you have a question about the 24VACH and is the answer not in the manual?
Questions and answers