Rear Panel Connections (Figure; Bare Wires And Pin Connectors (Figure - NAD C315BEE Owner's Manual

OPERATION
8 balance : The BALANCE control adjusts the relative levels of the left
and right speakers. The 12 o'clock position provides equal level to the
left and right channels. A detent indicates this position.
Rotating the control clockwise moves the balance towards the right.
Rotating the control anti-clockwise moves the balance to the left. The
BALANCE control does not affect recordings made using the Tape
outputs but will affect the signal going to the Speakers.
9 volume : The VOLUME control adjusts the overall loudness of the
signals being fed to the loudspeakers. It is motor driven and can be
adjusted from the remote control handset. The VOLUME control does
not affect recordings made using the Tape outputs but will affect the
signal going to the Speakers.
On the remote control handset, press the MUTE button to temporarily
switch off the sound to the speakers and headphones. Mute mode is
indicated by the active input LED flashing. Press the MUTE button again
to restore sound. Mute does not affect recordings made using the Tape
outputs but will affect the signal going to the Speakers.

REAR PANEL CONNECTIONS (FIGURE 2)

1 disc input : Input for additional line level input signals such as CD, Mini
Disc player or the output signal from a step-up amplifier for a turntable.
Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right
'Audio Outputs' to this input.
NOTES
When a 3.5mm stereo plug is inserted into the Front Panel MP socket,
the indicator above the socket will illuminate, and the DISC line-level
source will be disconnected.
It is recommended to mute the volume or switch to a different input
before plugging/unplugging the external Media Player cable.
2 cd input : Input for a CD or other line-level signal source. Use a twin
RCA-to-RCA lead to connect the CD player's left and right 'Audio
Outputs' to this input. The NAD C315BEE only accepts analogue signals
from your CD player.
3 video input : Input for the audio signal from a stereo VCR (or stereo
TV/Satellite/Cable receiver) or other line-level audio source. Using twin
RCA-to-RCA leads, connect to the left and right 'Audio Outputs' of the
unit to these inputs. Note: These are audio inputs only.
4 aux input : Input for additional line level input signals such as another
CD player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's
left and right 'Audio Outputs' to this input.
5 tuner input : Input for a tuner or other line-level signal source. Use
a twin RCA-to-RCA lead to connect the tuner left and right 'Audio
Outputs' to this input.
6 tape in/out : Connections for analogue recording and playback to an
audio tape recorder of any type. Using twin RCA-to-RCA leads, connect
to the left and right 'Audio Output' of the tape machine to the TAPE
IN sockets for playback and tape monitoring. Connect the left and
right 'Audio Input' of the tape machine to the TAPE OUT sockets for
recording.
to make a recording
When any source is selected, its signal is also fed directly to any tape
machine connected to the TAPE OUTPUT for recording.

7 Speakers : Speaker terminals for speakers with an impedance of 4
ohms or more. Connect the right speaker to the terminals marked 'R +'
and 'R-' ensuring that the 'R+' is connected to the '+' terminal on your
loudspeaker and the 'R-' is connected to the loudspeaker's '-' terminal.
Connect the terminals marked 'L+' and 'L-' to the left speaker in the
same way.
Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire to
connect loudspeakers to your NAD C315BEE. The high-current binding
post terminals can be used as a screw terminal for cables terminating in
spade or pin sockets or for cables with bare wire ends.

bare wireS and pin connectorS (figure 3)

Bare wires and pin sockets should be inserted into the hole in the shaft
of the terminal. Unscrew the speaker terminal's plastic bushing until
the hole in the screw shaft is revealed. Insert the pin or bare cable end
into the hole and secure the cable by tightening down the terminal's
bushing. Ensure bare wire from the speaker cables does not touch the
back panel or another socket. Ensure that there is only 1/2" (1cm) of
bare cable or pin and no loose strands of speakers wire.
8 ac line cord : Plug the AC power cord into a live AC wall socket. Make
sure all connections have been made before connecting to mains.
9 power Switch : The POWER switch supplies the master AC mains
power for the C315BEE. When this switch is in the ON position the
C315BEE is in standby as shown by the amber Status Condition L.E.D.
above the power switch on the front panel. If you intend not to use the
amplifier for long periods of time, switch the POWER switch to the OFF
position.
REMOTE CONTROL HANDSET AMP 1 (FIGURE 4)
The Remote Control handset handles all the key functions of the NAD
C315BEE and has additional controls to remotely operate NAD CD
machines. It will operate up to a distance of 16ft (5m). Alkaline batteries are
recommended for maximum operating life. One CR2025 battery should
be fitted in the battery compartment at the back of the Remote Control
handset (see Figure 4).
Please refer to previous sections of the manual for a full description of
individual functions.
When a command from the remote control is received, the Standby/
protection indicator will blink.
1 power on & off : The NAD C315BEE remote has a separate On and
Off button. This can be particularly useful to keep components within a
system "insync": This way all components will switch to stand-by when
Off is pressed or switch to operating mode when On is pressed, instead
of some components switching On when the amplifier is switched
to Stand-by. (Note that the other components have to be capable of
responding to the separate On and Off commands as well). Press the
ON button to switch the unit from Stand-by to the operating mode;
The Stand-by indicator (Fig. 1; No. 2) will turn from amber, to red, then
to green. Press the OFF button to switch the unit to the Stand-by mode:
The Stand-by indicator will light up amber.
2 mute : Press the MUTE Button to temporarily switch off the sound
to the speakers and headphones. Press MUTE again to restore sound.
Mute does not affect recordings made using the Tape output but will
affect the signal going to the Speakers.