Yamaha RX11 Owner's Manual page 11

1
.
Press
REAL TIME WRITE
button
to enter
real
time
write
mode.
2.
Enter
first
part of
time
signature via
white
number
buttons
(integer
markings,
two
digits).
3. Press
REAL TIME WRITE
button to
move
cursor to
second
part of
time
signature.
4.
Enter
second
part of
time
signature
via
number
buttons
(fraction
markings).
5.
Press
REAL TIME WRITE
button to
prompt
for
number
of bars
in
pattern.
6.
Enter
number
of bars
via
number
buttons, (integer
mark-
ings,
two
digits).
• The
real
time write
mode
can be exited
at
any
time by
pressing the
STOP/CONTINUE
button.
•Steps
2—6
above can
be
skipped
if
the default parameters
(4/4 time,
1
bar) are
acceptable.
You
are
now
ready to program your
pattern.
^Tap
the red
START
button
and you
will
hear the
"click
.tack"
rhythm
guide.
The
first
click
of each
bar
is
accented
(the actual
time
of the
click
function-whether
the
click
is
heard
on
every 1/4 note, every 1/8 note, etc.— can be
adjusted using the
CLICK
function to be
discussed
later).
The RX11
will
continue cycling through the
full
length of
the pattern while
you
record.
Adjust the
tempo
using
the
TEMPO
control,
and
start
playing.
For
multi-bar patterns
the
first
bar
can be located by watching the
LCD
display
panel:
e.g.
"REALT.W
BAR
02"
indicates that
the current
bar
is
bar
2.
There's
no need
to try
and
input
all
instruments
at
once. Just program one or
two
at a
time, adding
new
instruments on
successive cycles of the pattern. Input accent-
ed beats
by
using the
ACCENT
button (See
"Accents"
in
the
"THE INSTRUMENTS"
section).
Make
a
mistake?
Single notes can be cleared
by
holding
down
the
CLEAR
button
(top
row) and
tapping the appropriate
instrument button
at
the timing of the note that
is
to be
cleared.
When
the
pattern
is
complete,
press the
STOP/
CONTINUE
button.
You
can
add
new
instruments
and rhythm
lines
to already-
hprogrammed
patterns
by
simply
selecting
the pattern, entering
the
real
time
write
mode,
pressing the
START
button
and
writing
as usual.
The
time signature or bar length of
a
pro-
grammed
pattern
CANNOT
be changed.
Time
signature
and
number
of bars can only be
programmed
in
clear
patterns
(see
the
CLEAR
function, below).
Real-Time
Write
(EX:
3/8
time,
2
bars)
SELECT
PTM XX
"XX"
=
any
clear pattern
number.
<D
REALTIME STEP
Eorr INSERT
^
|
REALT.W.
04
/
4
1/4
3
i/|2
SAVE VERIFY
REALTIME STEP
©LZZ]
»
REALT.W.
03"/
4
*
REALT.W.
03
/
4h
EDIT INSERT
©I
^
|
REALT.W.
03
/
81
©
REALTIME STEP
EOT
INSERT
f
|
REALT.W.
01
BAR
(T)
\
1
^
1 I
"f
|
REALT.W.
02
"BAR
CD
m
|
REALT.W. BAR
02a
|
f
|
REALT.W.
BAR
Oil
|
Enter
pattern
guided by
click
function.
STOP CONTINUE
^
1
SELECT PTN XX
I
11