Basic Functions; Playing A Disc; Using The Search And Skip Functions - Samsung DVD-D360K User Manual

• HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission of video and audio data with just a single
connector.Using HDMI, the DVD player transmits a digital video and audio signal and displays a
vivid picture on a TVhaving an HDMI input jack.
• HDMI connection description HDMI connector
- Both uncompressed video data and digital audio data (LPCM or Bit Stream data).- Though the
player uses a HDMI cable, the player outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears
on the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the data trans-
mitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an
analog-to-digital converter (in the TV) is required. During this conver-sion, the picture quality is
degraded due to noise and signal loss. DVI technology is superior because it requires no D/A con-
version and is a pure digital sig-nal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted
via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a
display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized.
D. Connection to an Audio System (2 Channel Amplifier, Dolby Digital,
MPEG2)
1. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD
player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable, connect
the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO
IN (COAXIAL) terminal of the Amplifier.
2. Using the video signal cable(s), connect the VIDEO OUT terminals on the rear of the DVD player to
the VIDEO IN terminals of your TV
3. Turn on the DVD player, TV, and Amplifier.
4. Press the input select button of the Amplifier to select external input in order to hear sound from the
DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.
DVD-D360K
D
COAXIAL CABLE
BLUE GREEN
WHITE
RED
RED
YELLOW
A
VIDEO CABLE
AUDIO CABLE
B COMPONENT CABLE
YELLOW
RED WHITE
RED BLUE GREEN
WHITE
2-Channel stereo ampilfier,
RED
Dolby digital
WHITE
RED
DVD-D530K
DVD-D530
2-Channel stereo amplifier
or Dolby digital
D
Coaxial Cable
BLUE GREEN
WHITE
RED
YELLOW RED
Audio Cable
A
Video
B Component
Cable
Cable
RED WHITE
YELLOW
HDMI-DVI cable
RED BLUE GREEN

Basic functions

Playing a Disc

Before Play
- Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD POWER button, this screen comes up:
If you want to select a language, press the π/† button, and then press the ENTER button. (This
screen will only appear when you plug in the player for the first time.) If the language for the startup
screen is not set, the settings may change whenever you turn the power on or off. Therefore, make
sure that you select the language you want to use.
Once you select a menu language, you can change it by pressing the ®|| button on the front panel
of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE
window appears again where you can reset your preferred language.

Using the Search and Skip Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to
the next selection.
Searching through a Chapter or Track
During play, press the SEARCH (k or K) button on the remote control for more than 1 second.
WHITE
RED
Audio Cable
WHITE
RED
C
OR
HDMI cable
5