1. Manuals
  2. Brands
  3. Mercury Manuals
  4. GPS
  5. Pinpoint GPS
  6. Manual

Mercury Pinpoint GPS Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FCC and IC Compliance Statement
PINPOINT KEY FOB, FCC ID ‑ MVU10148
ACMA: N2523
IC: 6094A‑09291, 6094A‑09305
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including
interference that may cause undesired operation.
This device complies with FCC Rules. Changes or modifications not
expressly approved by MotorGuide could void the user's authority to
operate the equipment.
The MotorGuide Pinpoint GPS System complies with Industry Canada
RSS‑210 standard. See RSS‑GEN 7.1.5. The term "IC:" before the
certification/registration number only signifies that registration was
performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. The term "IC:" before the
certification/registration number does not imply that Industry Canada
approved the equipment.
EU Compliance Statement
Attwood Corporation hereby declares that the Motorguide Pinpoint GPS
System is in compliance with the essential requirements and other
relevant provisions of the 99/5/EC R&TTE directive.
A copy of the original CE Declaration of Conformity is on our website at
http://www.motorguide.com/support/certifications.
Environmental Compliance Statement
All MotorGuide products that are subject to the 2002/96/EC WEEE
directive are compliant with the WEEE marking requirement. Such
products are marked with the "crossed‑out wheelie bin" WEEE symbol
(shown, below) in accordance with European Standard EN50419.
eng
54539
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pinpoint GPS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Mercury Pinpoint GPS

Summary of Contents for Mercury Pinpoint GPS

  • Page 1 This device complies with FCC Rules. Changes or modifications not expressly approved by MotorGuide could void the user's authority to operate the equipment. The MotorGuide Pinpoint GPS System complies with Industry Canada RSS‑210 standard. See RSS‑GEN 7.1.5. The term "IC:" before the certification/registration number only signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met.

  • Page 2: Thank You

    Thank you for purchasing the MotorGuide Pinpoint GPS Navigation System. The Pinpoint GPS Navigation System is designed to enhance the precision control and functionality of your MotorGuide trolling motor. We're confident that the Pinpoint GPS will enhance your fishing experience and we appreciate that you chose MotorGuide. Warranty Message The product you have purchased comes with a Limited Warranty from MotorGuide.

  • Page 3: Table Of Contents

    Warranty Information MotorGuide Two Year Limited Warranty............1 Product Installation and Operation Installing the Pinpoint GPS Modules..............3 Operating the Pinpoint GPS System..............12 Owner Service Assistance Frequently Asked Questions and Troubleshooting........... 26 Service Assistance................... 27 Mercury Marine Service Offices................ 27...

  • Page 5: Warranty Information

    MotorGuide Two Year Limited Warranty KEEP YOUR ORIGINAL PURCHASE RECEIPT OR BILL OF SALE. 1. For recreational use customers, Pinpoint GPS components are warranted to the original retail purchaser to be free from defects in material or workmanship for a period of two years from the date of purchase.
  • Page 6 WARRANTY INFORMATION 6. We reserve the right to improve the design of any trolling motor or accessory without assuming any obligation to modify any trolling motor or accessory previously manufactured. 7. This warranty will not apply to: 1) haul‑out, launch, towing and storage, transportation charges and/or travel time, telephone or rental charges of any type, inconvenience, or loss of time or income, or other consequential damages;...

  • Page 7: Product Installation And Operation

    PRODUCT INSTALLATION AND OPERATION Installing the Pinpoint GPS Modules WARNING Before working around electrical system components, disconnect the battery cables from the battery to prevent injury or damage to the electrical system due to an accidental short circuit. 1. Starting with the negative (–) lead, disconnect the trolling motor battery cables from the battery, or unplug the trolling motor from the boat's power receptacle.
  • Page 8 PRODUCT INSTALLATION AND OPERATION 4. Place the upper GPS module into the trolling motor head as shown, with the GPS cable exiting the module from below. Secure the upper GPS module to the trolling motor head with two mounting screws. Push the power wires to one side to ease installation of the GPS cable.
  • Page 9 PRODUCT INSTALLATION AND OPERATION 5. Place the cover onto the trolling motor head. Ensure that the cable grommet is seated in the trolling motor head and that no wires are pinched. Install the five screws that secure the cover to the trolling motor head.
  • Page 10 PRODUCT INSTALLATION AND OPERATION 7. Remove the side panel screws from each side of the trolling motor. Gently pull the side panels away from the mount, taking care not to damage the locating tabs, and remove the side panels from both sides of the trolling motor.
  • Page 11 PRODUCT INSTALLATION AND OPERATION Route the male GPS connector through the slot, and connect it to the female GPS connector by aligning the pins and locating tabs in the connectors. Press the connectors together, then turn the nut 1/4 turn to the right until it locks. Gently press the lower GPS module into the opening until it is fully seated.
  • Page 12 PRODUCT INSTALLATION AND OPERATION 10. Install the status indicator light panel. Ensure that no wires are pinched between the status indicator light panel and the trolling motor, and that the GPS cable is positioned as shown. 54438 Status indicator light panel GPS cable 11.
  • Page 13 PRODUCT INSTALLATION AND OPERATION 12. Ensure that no wires are pinched between the side panels and the trolling motor. Tighten the side panel mounting screws. 54454 Side panel screws Locating tab LINKING THE HANDHELD REMOTE TO THE TROLLING MOTOR The first time the trolling motor is powered up, the handheld remote will need to be linked to the trolling motor.
  • Page 14 PRODUCT INSTALLATION AND OPERATION If you wish to clear the linked handheld from the trolling motor's memory, press the left arrow, right arrow, and propeller buttons at the same time. You will need to complete the link procedure again to use the handheld remote with the trolling motor.
  • Page 15 COMPASS CALIBRATION IMPORTANT: This calibration is completed at the factory. It should only be repeated if the Pinpoint GPS system is not responding properly. This calibration must be done with the boat in the water, using the primary propulsion engine.

  • Page 16: Operating The Pinpoint Gps System

    RESET TO FACTORY CALIBRATION To reset the trolling motor to the factory calibration, press and hold the manual mode button, then press 1, 1, 4. Operating the Pinpoint GPS System PINPOINT GPS STARTUP The global positioning system (GPS) is a satellite‑based navigation system capable of providing positional information anywhere on Earth, provided that the GPS receiver has a clear line of sight to at least four GPS satellites.
  • Page 17 PRODUCT INSTALLATION AND OPERATION When the trolling motor is powered up and deployed, it is immediately capable of operating as a conventional trolling motor. The trolling motor will require approximately 30 seconds to acquire a fixed GPS position. Having a clear view of the sky overhead, with no large trees, power lines, bridges, or buildings to interfere with the GPS signal, will improve the GPS accuracy and reduce the amount of time required to obtain a fixed GPS position.
  • Page 18 In order for anchor mode to operate, the Pinpoint GPS system must have achieved a fixed GPS location, indicated by the trolling motor emitting a three‑beep tune,...
  • Page 19 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 20 PRODUCT INSTALLATION AND OPERATION Adjusting the Anchor Position 54151 Left turn—"jog" left Increase speed—"jog" ahead Right turn—"jog" right Decrease speed—"jog" behind Once the trolling motor is in anchor mode, the anchor position can be adjusted by pressing any of the four buttons indicated above. Pressing the left turn, right turn, increase speed (+), or decrease speed (–) buttons once will adjust the anchor position by five feet in the direction selected, relative to the boat's heading.
  • Page 21 PRODUCT INSTALLATION AND OPERATION Storing or Overwriting an Anchor Position Memory buttons (1–8) 54420 NOTE: An anchor position can be stored or overwritten from any operating mode except route record mode. To store an anchor location, press and hold any of the numbered memory buttons for two seconds.
  • Page 22 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 23 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 24 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 25 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 26 WARNING Avoid serious injury from colliding with other boats, running aground, or striking objects in the water. The Pinpoint GPS system cannot detect other boats, shallow water, or objects in the water. Always beware of possible obstructions to navigation when operating in any Pinpoint GPS mode.
  • Page 27 SELECTING THE AUDIO MODE The Pinpoint GPS system has three user‑selectable audio modes to choose from. These audio modes provide audible confirmation of selected modes, speeds, and button selections.
  • Page 28 PRODUCT INSTALLATION AND OPERATION Audio Audio Mode 1 Audio Audio Condition Pattern (Default) Mode 2 Mode 3 Loss of GPS fix Error – Speed + (when less Short – – than maximum speed) beep Speed + (at maximum 2 beeps –...
  • Page 29 PRODUCT INSTALLATION AND OPERATION Audio Audio Mode 1 Audio Audio Condition Pattern (Default) Mode 2 Mode 3 Recalling an anchor point or route more Error than one mile away...

  • Page 30: Owner Service Assistance

    Finally, check the battery in the handheld remote and replace it if necessary. The Pinpoint GPS will not store an anchor point, recall a route, or hold a heading lock. Why is that? The GPS has not acquired a fixed GPS position. Allow at least 60 seconds for the GPS system to acquire a fixed GPS position.

  • Page 31: Service Assistance

    Model and serial number of your trolling motor • Proof of purchase or registration verification • Nature of problem Mercury Marine Service Offices For assistance, call, fax, or write. Please include your daytime telephone number with mail and fax correspondence. United States, Canada English ‑ (920) 929‑5040...
  • Page 32 OWNER SERVICE ASSISTANCE Japan Telephone 072‑233‑8888 Kisaka Co., Ltd. 4-130 Kannabecho Sakai-shi Sakai-ku 5900984 Osaka, 072‑233‑8833 Japan Asia, Singapore Telephone (65) 65466160 Brunswick Asia Pacific Group T/A Mercury Marine Singapore Pte Ltd 29 Loyang Drive (65) 65467789 Singapore, 508944...

Table of Contents