Harper 5400 Operator's Manual
  1. Manuals
  2. Brands
  3. Harper Manuals
  4. Chipper
  5. 5400
  6. Operator's manual

Harper 5400 Operator's Manual

Hide thumbs Also See for 5400:
Table of Contents

Advertisement

Quick Links

Download this manual
R
5400
1800
& Parts Manual
Chipper/Shredder
R
5/12
R
R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Harper 5400

Summary of Contents for Harper 5400

  • Page 1 5400 1800 & Parts Manual Chipper/Shredder 5/12...
  • Page 2 Chipper/Shredder...
  • Page 3 MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your dealer or Harper Industries, Inc. for clarification.
  • Page 4 TWELVE MONTHS from the original date of retail purchase to the original purchaser. Harper Industries will repair or replace, at our option, any part which our examina- tion shows to be defective. Warranty is limited to parts, labor and ground freight delivery of replacement parts.

  • Page 5: Table Of Contents

    Gasoline............Assembly........... Guards & Shields..........Option - Blower Attachment....Safety Decals............ Rotor..............Specific Safety Guidelines 1800 Decals............ CS-5400 PTO Powered Model......5400 Decals............ CS-1800 Gas Powered Model Engine....Towing............... Control Identification CS-5400 PTO Powered Model PTO Shaft........... 3-Point Hitch Pins.......
  • Page 6 Specifications Hopper Size 34” x 21” Chipper Plate ¾ thick machined and balanced steel plate Chipper Knives 4 knives machined from tool steel Chipper Chute 33”L x 13”W x 12”H Chipper Capacity 5” maximum diameter material Rotor 18” diameter with 36 free-swinging shredder knives Shredder Capacity 1”...

  • Page 7: Before Operation

    • If a foreign object should strike the General Safety Guidelines cutting mechanism of the machine and cause an unusual noise or vibration, shut the PTO engine off immediately SAFETY WARNING! and allow it to come to a complete Failure to understand and obey these stop.

  • Page 8: Gasoline

    Do not store gasoline in a room with • New decals may be obtained from an appliance that has a pilot light, or your local Harper Dealer. where electrical appliances with auto- matic switches could cause sparks. • Always store gasoline outside in a...

  • Page 9: Specific Safety Guidelines Cs-5400 Pto Powered Model

    • Always keep a fire extinguisher near Specific Safety Guidelines the Chipper/ Shredder during opera- tion. CS-5400 PTO Powered Model • Engine governor settings are pre- • Never operate the PTO unit when trac- set and should not be changed; any tor is moving.

  • Page 10: Point Hitch Pins

    CS-1800 18 HP Gas Powered Model Control Identification Shredder Chipper Hopper Chute CS-5400 PTO Powered Model Shredder Switch Hopper Chipper Fuel Chute Tank Discharge Discharge Hitch Jack Stand 3 pt. Engine Throttle Lever - The throttle lever Hitch controls engine speed and ranges...

  • Page 11: Cs-5400 Pto Powered Model

    Assembly SAFETY WARNING! • Keep pants and loose clothing away CS-5400 PTO Powered Model from PTO shaft and all other shafts, pul- 1. Mount feet onto machine base. leys and belts. 2. Connect PTO shaft to input shaft of machine, tighten set screws on shaft.

  • Page 12: Blower Attachment

    2. Connect the battery to a charger accord- • If electrolyte is taken internally, DRINK LARGE QUANTITIES OF ing to the manufacturer’s instructions and WATER OR MILK, FOLLOWED WITH charge at 10 amperes for 50 minutes, or 2-9 amperes for 2 hours (depending on MILK OF MAGNESIA, BEATEN capability of the charger).

  • Page 13: Discharge Grates

    5. Mount drive pulley on drum shaft. Align • A discharge grate with parallel bars is pulleys and tighten to 17 ft-lb. Mount belt available for shredding leaves or green on unit routing idler in center of belt. material. Install belt shield using 5/16” bolts and flat washers.

  • Page 14: Cs-5400 Pto Powered Model

    9. When restarting a warm engine, it should CS-5400 PTO Powered Model not be necessary to use the choke lever. 1. Obtain and wear safety goggles before If choking is necessary, open the lever operating the Chipper/Shredder.

  • Page 15: Chipping

    1” in diameter and 36” long into the shredder hopper. CS-5400 PTO Powered Model • Use a leaf tamper, branch or similar 1. Move throttle on tractor to the slow...

  • Page 16: Belt Adjustment

    Belt Adjustment Adjustments CS-5400 PTO Powered Model 1. Make certain that PTO shaft is removed SAFETY WARNING! from power source and un-mounted from • The cutting rotor is heavy and will 3-point hitch of tractor. continue to turn even though the operator has shut off the power source.
  • Page 17 CS-1800 18 HP Gas Powered Model 1. Loosen the four 3/8” x 1 1/2” bolts holding the engine. Rotor Shaft 2. Remove the belt and inspect or replace it. 3. Reinstall belt and draw engine back until there is ¼” up and down play in the belt. Use a straightedge and check for proper alignment.
  • Page 18 The chipper blades can be sharpened • Check nuts, bolts and fasteners to see with a bench grinder or done by a that they are secure. Harper dealership. • Avoid getting blade surface too hot to Lubrication where it changes color. This will re •...
  • Page 19 Setting Clearance: 4. Remove the knife shaft, knives and 1. Remove safety shields covering the drive spacers, and reverse or replace desired pulley on the rotor shaft front. shredder knives. 2. Remove safety cover on rotor shaft rear side. Reversing or Replacing: 3.
  • Page 20 Troubleshooting Engine Problem What to Check Engine will not start. • Improper control settings. • Engine may be low on fuel. • Engine may be low on oil. (The Honda Enine is equipped with “Oil-Alert” automatic shut-off) • Battery charge may be too low. •...
  • Page 21 5400 1800 Parts Section Chipper/Shredder...
  • Page 22 Chipper/Shredder...
  • Page 23 Table of Contents PARTS SECTION CS-1800 Chassis..........Rotor Drive......... Hitch........... Hopper..........CS-5400 Assembly..........Option - Blower Attachment....Rotor..............1800 Decals............5400 Decals............Chipper/Shredder...

  • Page 24: Chassis

    CS1800 CHASSIS Chipper/Shredder...

  • Page 25: Rotor Drive

    CS1800 ROTOR DRIVE Chipper/Shredder...

  • Page 26: Hitch

    CS1800 HITCH Chipper/Shredder...

  • Page 27: Hopper

    CS1800 HOPPER Chipper/Shredder...

  • Page 28: Assembly

    CS-5400 ASSEMBLY Chipper/Shredder...
  • Page 29 CS-5400 PART NO.S ITEM NO. PART NO. QTY. DESCRIPTION 910166 SPOUT DOOR 915052 1.5" GRATE WELDMENT 910167 TUB COVER 910168 DISCHARGE DOOR 940015 PTO SHAFT (SIZE 2) 940031 JACK SHAFT 900048 LONG FLAP MOUNT 910169 PTO JACK SHAFT GUARD 910170...

  • Page 30: Option - Blower Attachment

    Chipper/Shredder...
  • Page 31 Harper/Goossen Chipper/Shredder Blower Attachment Package - 900036 Item Part No. Description 1-2-3 915057 CRANK ASSEMBLY, SHORT HANDLE 915062 UPPER SPOUT ASSEMBLY 910400 DIRECTIONAL SPOUT DEFLECTOR 915060 LOWER DIRECTIONAL SPOUT 942036 1" FLANGE BEARING 900050 BLOWER IMPELLER SHAFT, 1" KEYED 915058...
  • Page 32 Chipper/Shredder...

  • Page 33: Rotor

    ROTOR Chipper/Shredder...

  • Page 34: 1800 Decals

    Chipper/Shredder...

  • Page 35: 5400 Decals

    CS-5400 Chipper/Shredder...
  • Page 36 Chipper/Shredder...
  • Page 37 Chipper/Shredder...
  • Page 38 Chipper/Shredder...

This manual is also suitable for:

1800

Table of Contents