Related Manuals for KTI KC-210TF-SXC
Summary of Contents for KTI KC-210TF-SXC
- Page 1 1000BASE-T to 1000BASE-SX/LX Media Converters KC-210TF-SXC KC-210TF-SXC-O KC-210TF-LXC KC-210TF-LXC-O KC-210TF-LXC30-O KC-210TF-LXC40 KC-210TF-LXC80 Installation Guide P/N: 750-0158-002 DOC.050727-KC210...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ............3 1.1 Specifications ................4 2. Installation ............5 2.1 Media Converters ................5 2.2 LED Indicators ................7 2.3 Applying Power ................8 2.4 Making Connection ................ 9 The information contained in this document is subject to change without prior notice. -
Page 3: Introduction
1000BASE-X device • Full LED indicators for monitoring port and connection status The converter series support the following configuration needs: 1000BASE-T to 1000BASE-SX / LX KC-210TF-SXC Copper to SX fiber 850nm SC KC-210TF-LXC Copper to LX fiber 1310nm SC KC-210TF-LXC30... -
Page 4: Specifications
1.1 Specifications Twisted-Pair Interface Compliance IEEE 802.3ab 1000BASE-T Connector Shielded RJ-45 jack Pin assignments Auto-crossover for MDI and MDI-X Data speed 1000Mbps Duplex mode Auto-negotiation for half-duplex or full-duplex Cable type 4-pair Category 5 UTP Supported cable length 100 meters Fiber Optic Interface Compliance IEEE 802.3z 1000BASE-SX or LX... -
Page 5: Installation
2. Installation 2.1 Media Converters Functions of 1000BASE-T Port (Twisted-Pair Interface) • Auto-negotiation support for connecting to auto-negotiation devices • Supports both of half duplex and full duplex operations • Auto MDI/MDI-X crossover configuration and receiving polarity correction for UTP connection Pin Assignments MDI-X BI_DA+... - Page 6 Note: 1. For connecting to early 1000BASE-X devices which do not provide auto negotiation capability, you might need to set the SW to NON- AUTO position to prevent unexpected link failure occurrence. 2. In most of the cases, setting AUTO would make the link worked. 3.
-
Page 7: Led Indicators
2.2 LED Indicators Name Status State Interpretation Power status Power on Power off TP-LNK UTP link status TP Link up TP Link down TP-FDX UTP duplex status TP full-duplex TP half-duplex TP-RX UTP Rx status TP Receiver in operation TP no receiving operation TP-TX UTP Tx status TP Transmitter in operation... -
Page 8: Applying Power
2.3 Applying Power The DC input of the converter is: DC Input Jack DC input rated voltage +5VDC DC input voltage range +4.75 ~ 5.25VDC DC power consumption max. 0.8A @+5V (4 Watts) DC input Jack Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. -
Page 9: Making Connection
2.4 Making Connection The figure below shows the configuration used when connecting to auto-negotiation device and non-auto-negotiation device. For proper communication, the UTP connections on both ends must be in same configuration, either 1000M full-duplex or 1000M half-duplex. Set Auto SW to NON-AUTO mode to use forced full duplex mode for fiber connection.
Need help?
Do you have a question about the KC-210TF-SXC and is the answer not in the manual?
Questions and answers