1. Manuals
  2. Brands
  3. Phoenix Doors Manuals
  4. Gate Opener
  5. Enviro 6S
  6. User manual

Phoenix Doors Enviro 6S User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Sliding Gate Operator
User's Manual
E N V I R O 6 S
G e a r -D r i v e n
http://www.phoenixgaragedoors.com.au/

Advertisement

Table of Contents
loading

Related Manuals for Phoenix Doors Enviro 6S

Summary of Contents for Phoenix Doors Enviro 6S

  • Page 1 Sliding Gate Operator User's Manual E N V I R O 6 S G e a r -D r i v e n http://www.phoenixgaragedoors.com.au/...

  • Page 2: Table Of Contents

    ENVIRO 6S SLIDING GATE OPERATOR OUTLINE 1. Products introduction 2. Important safety precautions 3. Main technical parameters 4. Mechanical Installation 5. Adjustment 6. Wire Connecting 7. Electrical and control board 8. Porgramming Process 9. Maintenance 10. Trouble Shooting 11. Packing list...

  • Page 3: Products Introduction

    ENVIRO 6S SLIDING GATE OPERATOR 1. Products introduction please read the instructions carefully before proceeding. The operator contains Extra battery, transformer, control board and radio control. In case of power of failure, the operator is powered by a 24Vdc, 1.3Ah, extra battery.

  • Page 4: Mechanical Installation

    ENVIRO 6S SLIDING GATE OPERATOR 4. Mechanical Installation The ENVIRO 6S will handle gate weighting up to 300Kg and up to 8m if the proper installation procedures have been followed. The ENVIRO 6S gate operator operates by forcing a drive rack by a drive gear. The entire configuration is shown in the diagram below.
  • Page 5 ENVIRO 6S SLIDING GATE OPERATOR Gate operator Gear Spring washer Plain washer Groundsill Input power Fig.2 Operator base (see Fig.3) After the concrete has hardened, mount the gate operator base to the concrete pad. Verify that the base is properly leveled.

  • Page 6: Adjustment

    ENVIRO 6S SLIDING GATE OPERATOR Installation of Rack Fix the three nuts (in the same package with rack) on the rack element. Lay the first piece of rack on the gear and weld the first nut on the gate. Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut.

  • Page 7: Wire Connecting

    ENVIRO 6S SLIDING GATE OPERATOR Manual operation In case of power failure use manual release key to open or close gate manually, use the release key as follow: Fit the supplied key in the hole. Turn the key clockwise to release the clutch.

  • Page 8: Electrical And Control Board

    ENVIRO 6S SLIDING GATE OPERATOR Connecting the motor Connect motor wires to M- and M+ of terminal block T1 (BLACK)and T2(RED). Connecting power wire Power Transformer supply primary AC220V Fig.8 7.Electrical and control board Fig.9 Motor: black wire to T1 and red wire to T2.

  • Page 9: Porgramming Process

    ENVIRO 6S SLIDING GATE OPERATOR operator. 8. Programming Process SET button: Mode set and Confirm function CODE button: Transmitter set and clear function OPEN button: open door CLOSE button: close door OPEN CODE CLOSE Fig.10 Adding extra transmitter (learn) 1. Press CODE, a dot is indicated on the LED display.
  • Page 10 ENVIRO 6S SLIDING GATE OPERATOR Set open and close positions 1. Press and hold SET until number 1 is indicated on the LED display. 2. Press and hold OPEN to set open position(now the door must be OPEN,, if not,please change the motor wire red and black), release the button until the door has reached the desired position.

  • Page 11: Maintenance

    ENVIRO 6S SLIDING GATE OPERATOR If the door meet an obstruction during closing, it will stop and reverse about 15cm~20cm. 1. Press and hold SET. The LED will display number from ’1’ to ’4’, when the number ’3’ appears on the LED display, release the SET.

  • Page 12: Troubleshooting

    ENVIRO 6S SLIDING GATE OPERATOR Be sure to read the entire manual before attempting to perform any installation or service to the door operator. Our company reserves the right to change the design and specification without prior notification. 10. Troubleshooting...

Table of Contents