Dimplex WPM 2006 plus Operating Instructions Manual
Heat pump controller
Hide thumbs
Also See for WPM 2006 plus:
- Installation and start-up instructions manual (132 pages) ,
- Operating instructions manual (54 pages) ,
- Operating instructions for users (66 pages)
Table of Contents
Advertisement
WPM 2006 plus
WPM 2006 R
WPM 2007 plus
WPM 2007 R
Wärmepumpen-
Manager
für Nieder-, Mittel- und
Hochtemperatur–Wärme-
pumpen zum Heizen und
Kühlen
Bestell-Nr. / Order no. / N
Heat Pump
Controller
for Low, Medium and
High-Temperature Heat
Pumps for Heating and
Cooling
o
de commande : 452114.66.48
Bedienungsanleitung
für den Benutzer
Operating instructions
for Users
Manuel d'utilisation
Regulateur de
pompe à chaleur
pour des pompes à chaleur
à basse température,
à température moyenne
et à haute température
– pour le chauff age et le
rafraîchissement
FD 8609
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dimplex WPM 2006 plus
Summary of Contents for Dimplex WPM 2006 plus
-
Page 1: Operating Instructions
WPM 2006 plus Bedienungsanleitung WPM 2006 R für den Benutzer WPM 2007 plus Operating instructions for Users WPM 2007 R Manuel d’utilisation Wärmepumpen- Heat Pump Regulateur de Manager Controller pompe à chaleur für Nieder-, Mittel- und for Low, Medium and pour des pompes à... -
Page 2: Table Of Contents
Table of Contents 1 General Information ............................E-2 2 Heat Pump Manager............................E-2 3 Quick Reference Instructions ........................E-3 3.1 Selection of the Operating Mode ..............................E-3 3.2 Changing the Settings ...................................E-3 3.3 Settings and Operating Data .................................E-3 4 Operation .................................E-4 5 Operating Modes.............................E-5 6 Adjustment of Heating Operation........................E-5 7 DHW Heating ..............................E-6 7.1 Shut-Off times for DHW Preparation .............................E-6... -
Page 3: General Information
1 General Information For installation, operation and maintenance refer to the recycling and disposal of materials and components should be installation and operating instructions. This device should only be observed in accordance with the applicable standards. installed and repaired by a competent technician. Poorly carried Regulations and Safety Information! out repairs can endanger the safety of the user. -
Page 4: Quick Reference Instructions
3 Quick Reference Instructions 3.1 Selection of the Operating Mode Select the desired operating mode by repeatedly pressing the modus button (text message). The operating mode will change 10 seconds after altering the setting (symbol changes on the display). Cooling The system operates in cooling operation. -
Page 5: Operation
4 Operation The heat pump manager is operated using 6 pushbuttons: 6 different operating modes can be selected: Esc, Modus, Menue, . Different functions are assigned Cooling, Summer, Auto, Party, Vacation, 2nd heat ⇓ ⇑ ↵ to these buttons according to the current display (Standard generator. -
Page 6: Operating Modes
5 Operating Modes 6 different operating modes can be selected using the button NOTE (Modus). There is a time delay between switching modes. The Heat pump operation block operating mode can be changed each time the button is pressed The heat pump is blocked in the 2nd heat generator operating mode. in the order shown below. -
Page 7: Dhw Heating
7 DHW Heating The heat pump manager automatically calculates the maximum is terminated once the so-called HP maximum temperature is possible hot water temperature in heat pump operation. The reached. desired hot water temperature can be set in the menu “Settings Hot water cylinder with flange heater –... -
Page 8: Menu Structure
8 Menu Structure 8.1 Settings NOTE All user settings are made in the “Settings” menu item. The following table shows not only the menu structure and Dynamic menus The following contains a description of the complete menu. During start- explanations right-hand column, also... - Page 9 System-specific parameters Setting range For each day of the week, it is possible to select whether Time1, Time2, no time or both times are to be active when the temperature is raised. Operations to raise the temperature that exceed a week day are activated or deactivated at the end of each day accordingly.
- Page 10 System-specific parameters Setting range To carry out a thermal disinfection, the DHW is heated up once to the desired temperature. The heating period is terminated automatically when the set temperature is reached or after 4 hours at the latest. Sets the start time for the thermal disinfection 00:00 23:59 Sets the desired hot water temperature which is to be reached...
-
Page 11: Operating Data
8.2 Operating Data All current operating statuses are displayed in the “Operating Selecting the operating data menu item with the arrow data” menu item. buttons and confirming with the ENTER button Depending on the system configuration, the following data can You can access the operating data menu by: be queried in the “Operating data”... - Page 12 Display of sensor and system values Display Displays the temperature measured on the “Antifreeze Cool” Reversible HP sensor. Cooling operation This temperature is used to safeguard the operating limits in cooling operation. Displays the current room set temperature with silent cooling. Cooling function Silent cooling Cooling operation...
-
Page 13: History
8.3 History The “History” menu can be used to query the runtimes of the Selecting the history menu item with the arrow buttons and compressor(s), circulating pumps and further components in the confirming with the ENTER button heat pump heating system. Depending on the system configuration, the following data is available: You can access the history menu by:... -
Page 14: Displays
9 Displays The current operating status of the heat pump system can be read from the LC display. 9.1 Normal Operating Statuses The display shows both normal operating statuses and those that heat pump. Only information about the relevant system are required by utility companies or due to safety functions of the configuration and HP type are shown on the display. -
Page 15: Fault Messages
Despite a pending request, the chiller is unable to cool because antifreeze (frost protection) was activated. This state is ended automatically. Despite a pending request, the chiller is unable to cool because the current flow temperature is under the operating limit. This state is ended automatically. Despite a pending request, the chiller is unable to cool because the dew point monitor has been activated (external input). - Page 16 Garantiebedingungen Kundendienstadresse siehe Irrtümer und Änderungen vorbehalten. Montage- und Gebrauchsanweisung Wärmepumpe. Subject to alterations and errors. Sous réserve d’erreurs et modifications. For the terms of the guarantee and after-sales service addresses, please refer to the Installation and Operating Instructions for Heat Pumps. Pour les conditions de garantie et les adresses SAV, se référer aux instructions de montage et d'utilisation de la pompe à...
- Page 17 WPM 2006 plus WPM 2006 R Quick Reference Instructions WPM 2007 plus WPM 2007 R 1. Key assignment The heat pump manager is operated using 6 keys: Change the operating mode by pushing the key once or repeatedly: Modus Briefly touch The filled square in the upper right corner of the display indicates the current operating mode.
- Page 18 WPM 2006 plus WPM 2006 R Quick Reference Instructions WPM 2007 plus WPM 2007 R 3. Domestic hot water preparation How to set the domestic hot water temperature and the hot water block: Keep pressed Menue Jump to the menu to modify Settings.
Need help?
Do you have a question about the WPM 2006 plus and is the answer not in the manual?
Questions and answers