Renault 2016 ESPACE Handbook
  1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. 2016 ESPACE
  6. Handbook

Renault 2016 ESPACE Handbook

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Renault ESPACE
Driver's handbook

Advertisement

Table of Contents
loading

Related Manuals for Renault 2016 ESPACE

Summary of Contents for Renault 2016 ESPACE

  • Page 1 Renault ESPACE Driver’s handbook...
  • Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.

  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.

  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 The RENAULT card: general information and use ........

  • Page 8: Battery Life

    “Keycard battery low” appears on the 4 Switching on the lighting remotely. instrument panel (refer to the informa- tion on the “RENAULT card: battery” in section 5). When the battery is flat, you can still lock/unlock and start your vehi- cle.
  • Page 9 RENAULT CARD: general information (2/2) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in Driver’s responsibility a place where it could be bent or when parking or stopping damaged accidentally, such as in a the vehicle back pocket of a garment.
  • Page 10 There are two ways to unlock/lock the vehicle: – the RENAULT card in “Hands-free” mode; – the RENAULT card in remote con- trol mode. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone in your vehicle, even for a short time.
  • Page 11 Remote “Hands-free” locking the sensor 3, there is a delay of approx- imately 3 seconds before it can be un- With the RENAULT card in zone 1, With the RENAULT card on you, and locked again. During these 3 seconds,...
  • Page 12 Note: The maximum distance at which system (continued) the vehicle locks depends on the sur- control roundings. If the RENAULT card has been within Unlocking with the card RENAULT range for approximately 15 minutes, Special features Press the button 5.
  • Page 13 RENAULT “HANDS-FREE” CARD: usage (4/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone in your vehicle, even for a short time. They may pose a risk to themselves...

  • Page 14: Locking/Unlocking The Doors

    If the RENAULT card does not work: In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.);...
  • Page 15 – Insert the key 2 into the lock and lock from the inside or by using the key in or unlock the front left-hand door. the front left-hand door. Once you are inside the vehicle, put the key back in its casing in the RENAULT card.
  • Page 16 Unlocking the vehicle from the outside When you lock the doors from the out- is only possible with the RENAULT card side, the indicator light remains lit for a in the vehicle's access zone or using moment, and then goes out.

  • Page 17: Opening And Closing The Doors

    Opening the doors from the Opening from the inside outside Pull on the handle 2. With the doors unlocked or RENAULT card on you, hold handle 1 and pull it towards you. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary.
  • Page 18 OPENING AND CLOSING THE DOORS (2/3) Once the vehicle reaches a speed of approximately 12 mph (20 km/h), a war- ning light indicates if the door(s) or lug- gage compartment are open or impro- perly closed, along with the message «Boot open»...

  • Page 19: Child Safety

    OPENING AND CLOSING THE DOORS (3/3) Driver’s responsibility As a safety precaution, when parking or stopping the doors should only be the vehicle opened or closed when the Never leave an animal, vehicle is stationary. child or adult who is not self-suffi- cient alone on your vehicle, even for a short time.

  • Page 20: Automatic Locking When Driving

    AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the Operating faults function If you experience an operating fault (no To switch it on: with the vehicle at a automatic locking, the indicator light in- standstill and the engine running, press corporated in switch 2 does not light up switch 2 until a beep sounds.

  • Page 21: Front Headrests

    FRONT HEADRESTS To adjust side supports B Depending on the vehicle, sections B can be adjusted independently to the desired position. To remove the headrest Raise it to its highest position (tilt the seatback backwards if necessary). Press button 2 and lift the headrest to release it.
  • Page 22 FRONT SEATS WITH MANUAL CONTROL (1/2) To tilt the seatback Lift handle 3 and tilt the seatback to the desired position. Release the handle at the desired position and make sure that it is locked. To move the seat forwards or To adjust the seat’s lumbar back position...
  • Page 23 FRONT SEATS WITH MANUAL CONTROL (2/2) Operating faults When an operating fault is detected, the integrated warning lights on the switch 5 for the seat concerned flash. Consult an approved dealer. Heated seats With the ignition on: – Pressing the switch 5 on the requi- For safety reasons, make red seat for the first time activates these adjustments only...

  • Page 24: Adjusting The Lumbar Support

    DRIVER’S SEAT WITH ELECTRIC CONTROLS (1/2) Adjusting the seatback To tilt the seatback, move the top of switch 2 forwards or backwards. Adjusting the lumbar support on the driver’s seat Move the switch 3 forwards, back- wards, up or down. For safety reasons, carry On equipped vehicles, switch 1 grants out any adjustments when...

  • Page 25: Adjusting The Seat Position

    DRIVER’S SEAT WITH ELECTRIC CONTROLS (2/2) Adjusting the seat length Lift handle 5 to unlock. Release the handle at the desired position and make sure that it is locked. Adjusting the seat position Heated seats To move the seat forwards or back With the ignition on: Move switch 4 forwards or backwards.
  • Page 26 FRONT SEATS: Functions (1/3) Browse menu “Driver” or “Passenger” Massage Driver Passenger – select the type of massage (Tonic, Massage Relaxing or Lumbar); – adjust the intensity (+ or -); – adjust the speed (+ or -); Relaxing Lumbar Tonic –...
  • Page 27 FRONT SEATS: Functions (2/3) Easy driver and passenger access Press “ON” or “OFF” to activate or de- Easy access driver activate this function. Easy access passenger When this function is activated, the seat automatically moves back when Courtesy for passenger the driver or passenger leaves the vehi- cle, and returns to its position when the Position...
  • Page 28 The driving position can be stored and recalled by pressing the buttons: – RENAULT hands-free card detected; – when the driver’s door is opened. Recall Save Storing your driving position Recalling the driving position –...

  • Page 29: Seat Belts

    SEAT BELTS (1/3) Always wear your seat belt when tra- Before starting, first adjust your dri- velling in your vehicle. You must also ving position, then ask all occupants comply with the legislation of the parti- to adjust their seat belts to ensure cular country you are in.
  • Page 30 SEAT BELTS (2/3) Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt remin- This lights up on the interior rear-view mirror when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fas- tened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around...

  • Page 31: Front Seat Belts

    SEAT BELTS (3/3) – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special op- erations (e.g. fitting child seats) contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.

  • Page 32: Rear Seat Belts

    REAR SEAT BELTS Second row rear side seats Second row centre rear seat Third row rear seats (7-seater versions) Slowly unwind belt 1. Unwind belt 5 slowly from its housing 4. Slowly unwind the strap 10. Click the sliding buckle 2 into the corre- Click buckle 9 into black catch 8.
  • Page 33 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...

  • Page 34: Methods Of Restraint In Addition To The Front Seat Belts

    METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter airbags for driver and passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
  • Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light comes on when the engine is started and then goes out after approximately three sec- onds. If it does not come on when the ignition is switched on or if it stays on, there is a fault in the system.
  • Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
  • Page 37 METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
  • Page 38 SIDE PROTECTION DEVICES Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Curtain air bags These are airbags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear door side win-...

  • Page 39: Additional Methods Of Restraint

    ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt.

  • Page 40: Steering Wheel/Power-Assisted Steering

    STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering NB: power-assisted steering depends on the mode selected in the “Multi- Variable power-assisted steering Sense” menu (please refer to the infor- mation in “Multi-Sense” in Section 3). The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed.

  • Page 41: Child Safety: General Information

    CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
  • Page 42 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 43 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.

  • Page 44: Choosing A Child Seat Mounting

    CHILD SAFETY: choosing a child seat mounting (1/3) There are two ways of attaching child Attachment via the seat belt seats: via the seat belt or using the The seat belt must be adjusted to ISOFIX system. ensure that it is effective in the event of harsh braking or an impact.
  • Page 45 CHILD SAFETY: choosing a child seat mounting (2/3) Attachment using the ISOFIX Attach the child seat with the ISOFIX system locks, if these are provided. The ISOFIX system allows quick, easy, safe fitting. Approved child seats ISOFIX are stand- ardised in accordance with current reg- The ISOFIX system consists of 2 rings ulations if any of the four cases below and, in some cases, a third ring.
  • Page 46 CHILD SAFETY: choosing a child seat mounting (3/3) The rings are located on the rear seat-  backs and indicated by the symbol In all cases, attach the strap hook to the corresponding ring (3 and 5 for the rear side seats and 4 for the rear centre seat) and place the seat in the desired position.

  • Page 47: Fitting A Child Seat, General Information

    CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting The types of child seat indicated may After installing the child seat, if neces- child seats. The diagram on the follow- not be available. Before using a differ- sary, the seat may be advanced (so as ing page shows you how to attach a ent child seat, check with the manufac-...
  • Page 48 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear seat For 7-seater vehicles, the second row rear seats must be pushed forward A carrycot can be installed across the before a child is seated in the third row vehicle and will take up at least two rear seats.
  • Page 49 CHILD SEATS: attachment by seat belt (1/6) Visual installation of the five-seater version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬...
  • Page 50 CHILD SEATS: attachment by seat belt (2/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Five-seater version Front passenger Type of child seat Weight of the child Rear side seats Rear centre seat seat (1)
  • Page 51 CHILD SEATS: attachment by seat belt (3/6) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats.
  • Page 52 CHILD SEATS: attachment by seat belt (4/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Seven-seat version Front passenger Row 2 rear Row 2 rear Row 3 rear Type of child seat Weight of the child...
  • Page 53 CHILD SEATS: attachment by seat belt (5/6) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats.
  • Page 54 CHILD SEATS: attachment by seat belt (6/6) Installation diagram, 7-seater version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬...
  • Page 55 CHILD SEATS: attachment using the ISOFIX system (1/6) Visual installation of the five-seater version Child seat fitted using the ISOFIX mounting  Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
  • Page 56 CHILD SEATS: attachment using the ISOFIX system (2/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Five-seater version Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats Rear centre seat...
  • Page 57 CHILD SEATS: attachment using the ISOFIX system (3/6) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “universal”...
  • Page 58 CHILD SEATS: attachment using the isofix system (4/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Seven-seat version Front Row 3 rear Weight of Seat size Row 2 rear Row 2 rear Type of child seat...
  • Page 59 CHILD SEATS: attachment using the isofix system (5/6) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “universal”...
  • Page 60 CHILD SEATS: attachment using the isofix system (6/6) Visual installation of seven-seater version Child seat fitted using the ISOFIX mounting  Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.

  • Page 61: Deactivating/Activating The Front Passenger Airbag

    CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the ve- hicle is being driven, indicator lights å ©...
  • Page 62 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (example: label shown above) remind you of these instruc- tions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
  • Page 63 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.

  • Page 64: Driving Position

    DRIVING POSITION (1/2) 13 14 1.58...

  • Page 65: Instrument Panel

    DRIVING POSITION (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 18 Storage compartment. 1 Side air vent. 11 Multimedia touchscreen. 2 Side window demister outlet. 12 Multifunction screen controls: 19 Assisted parking brake control. – screen activation/deactivation; 3 Stalk for: –...
  • Page 66 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Side light warning light Left-hand direction indicator š tell-tale Main beam headlight tell- Right-hand direction indica- á tale tor tell-tale Dipped beam headlight tell- Low fuel level warning light tale It lights up orange when the ig-...
  • Page 67 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Brake circuit fault warning Oil pressure warning light À light It lights up when the ignition or It lights up when the ignition or the the engine is switched on and goes off engine is switched on and goes off after after a few seconds.
  • Page 68 WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Toxic Fume Filter System Anti-lock braking warning Ä Warning Light light On vehicles which are equipped with it, It lights up when the ignition or the this light comes on when the engine is engine is switched on and goes off after started and, depending on the vehicle,...
  • Page 69 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Rear seat belt reminder (depending Air bag warning light å on vehicle) This warning light will be dis- played on the instrument panel when ß...
  • Page 70 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Unavailability of engine Warning light  © standby warning light This lights up when the ignition Please see information in the para- or engine is switched on and goes out graph on “Stop and Start Function”...
  • Page 71 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt remin- der. This lights up in the rear-view mirror when the ignition is started then, if the driver or front passenger seat belt (if this seat is occupied) is not fastened...

  • Page 72: Trip Computer And Warning System

    DISPLAYS AND INDICATORS (1/4) Driving style indicator 3 Please refer to the information on “Eco- driving” in Section 2. Trip computer and warning system Refer to the information on the “Trip computer and warning system” in Section 1. Instrument panel A Rev counter 1 (graduations x 1000) You can customise your instrument...
  • Page 73 DISPLAYS AND INDICATORS (2/4) Engine oil level low warning Coolant temperature indicator 5 Fuel gauge 6 In normal use, indicator 5 should be When the engine is started, the instru- If the level is at the minimum, warn- before area B. Under “intensive” ope- ment panel display A alerts you when ing light integrated in the indica-...

  • Page 74: Displays And Indicators

    DISPLAYS AND INDICATORS (3/4) You can adjust certain settings from the multifunction screen: with the engine running, access menu “System”, “Display” then “Head-up display”. Adjusting the display information height Depending on your driving position, you can raise or lower the information on the display.
  • Page 75 DISPLAYS AND INDICATORS (4/4) Operating faults In the event of a malfunction (the dis- play fails to open when the engine is started, or the display retracts, with the engine running, following an object im- pacting the display): – stop and restart the engine; –...
  • Page 76 TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on button 2 (the display depends on the vehicle equipment and country): a) total mileage and trip mileage re- corder; b) journey parameters: –...
  • Page 77 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
  • Page 78 ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Fuel used b) Journey parameters: Fuel used.
  • Page 79 ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range b) Journey parameters (continued): Estimated range with remaining fuel. 541 km The value is displayed after driving 400 metres. Distance Distance travelled since last reset.
  • Page 80 ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in With the ignition switched on, the engine not running and Service Intervals...
  • Page 81 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
  • Page 82 ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure reset Refer to the information on the “Tyre pressure Tyre pressure monitoring system” in Section 2. No message e) Trip log.
  • Page 83 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
  • Page 84 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
  • Page 85 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.

  • Page 86: Vehicle Settings Customisation Menu

    VEHICLE SETTINGS CUSTOMISATION MENU Adjusting the settings Select the function to modify: a) unlocking the driver’s door; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome; g) reading lamp in automatic mode; h) rear windscreen wiping in reverse gear;...

  • Page 87: Clock And Exterior Temperature

    CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (sig- nalling a risk of ice on the road). The time and/or external tempera- ture are displayed on the multifunc- tion screen 1 Refer to the handbook for the equip- ment.

  • Page 88: Rear View Mirrors

    – when the ignition is next switched on Automatic mode is then deactivated. To (function deactivated); reactivate it, position switch 3 to B. – upon detecting the RENAULT card or upon unlocking the vehicle (func- tion activated). Door mirrors Adjustment...
  • Page 89 REAR-VIEW MIRRORS (2/3) Position memory Recalling the memorised position – Adjust the door mirrors (see previous paragraphs); From the multifunction screen, select – from the multifunction screen, select menu “Vehicle”, “Seats”, “Settings” then menu “Vehicle”, “Seats”, “Settings” “Position” and select “Recall”. then “Position”...

  • Page 90: Interior Rear View Mirror

    REAR-VIEW MIRRORS (3/3) Special feature: Interior rear view mirror When the rear-view mirror has been The rear-view mirror 4 automati- manually deployed or folded back, it is cally darkens when you are being fol- possible to reset it to a usage position. lowed by a vehicle using main beam To do this, position the switch 3 to C.

  • Page 91: Audible And Visual Signals

    AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.

  • Page 92: Exterior Lighting And Signals

    EXTERIOR LIGHTING AND SIGNALS (1/5) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the ins- trument panel comes on. Automatic operation Turn ring 3 until the AUTO symbol is op- posite mark 2: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
  • Page 93 EXTERIOR LIGHTING AND SIGNALS (2/5) Automatic main beam Activation  Turn ring 3 until the AUTO symbol is op- headlights posite mark 2. Depending on the vehicle, this system Push stalk 1 to activate the main beam switches the main beam headlights on ...

  • Page 94: Daytime Running Lights

    EXTERIOR LIGHTING AND SIGNALS (3/5) Daytime running lights Switching off the lights function There are two possibilities: – manually, move ring 3 to position 0; The daytime running lights come on – automatically, the lights will go out automatically with no action on stalk 1 when the engine is switched off, the when the engine is started, and they go driver’s door is opened or the vehicle...

  • Page 95: Door Mirrors

    Renault card or when the vehicle is RENAULT card, upon unlocking the With the engine and lights off and unlocked.

  • Page 96: Rear Fog Lights

    EXTERIOR LIGHTING AND SIGNALS (5/5) Switching off the lights Turn ring 4 again until mark 2 is oppo- site the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out. The rear fog lights switch off when the exterior lights are switched off.

  • Page 97: Windscreen Wash/Wipe

    WINDSCREEN WASH/WIPE (1/6) Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Vehicle fitted with intermittent Special note water; When driving the vehicle, the wiping windscreen wipers –...
  • Page 98 WINDSCREEN WASH/WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers.
  • Page 99 WINDSCREEN WASH/WIPE (3/6) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the vehi- intermittent wiping. Contact an au- cle stops. For example, fast wiping thorised dealer.

  • Page 100: Service Position

    WINDSCREEN WASH/WIPE (4/6) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the winds- the blades.

  • Page 101: Windscreen Washer

    WINDSCREEN WASH/WIPE (5/6) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the winds- creen washer.

  • Page 102: Headlight Washers

    WINDSCREEN WASH/WIPE (6/6) Note: To ensure the headlight washers ope- rate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.

  • Page 103: Rear Screen Wiper

    REAR SCREEN WASH/WIPE (1/2) To stop the operation, pivot ring 3 again. Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate auto- matic wiping. Follow usage recommendations. Check the condition of the wiper blades.
  • Page 104 REAR SCREEN WASH/WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. Engaging reverse gear triggers inter- If an obstacle prevents the blade from mittent wiping (if the front wipers are in moving, it can be stopped.

  • Page 105: Diesel Versions

    FUEL TANK (1/3) Diesel versions Only use diesel fuel which complies with the information on the label located inside the cover 1. Petrol versions It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover 1.
  • Page 106 FUEL TANK (2/3) Filling with fuel Insert the nozzle to open the valve 2 and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts...
  • Page 107 (unless undertaken by qualified Network personnel). Running out of fuel on diesel versions Persistent smell of With the card RENAULT in the pas- fuel senger compartment, press the start If you notice a persistent button 3 without pressing any of the smell of fuel you should: pedals.
  • Page 108 1.102...
  • Page 109 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting - Stopping the engine .

  • Page 110: Running In

    RUNNING IN Petrol version Diesel version Up to 600 miles (1 000 km), do not For the first 900 miles (1 500 km), do exceed 78 mph (130 km/h) in top gear not exceed 2,500 rpm. After complet- or 3,000 to 3,500 rpm. ing this mileage you may drive faster, however, it is only after approximately You may only expect top performance...

  • Page 111: Starting/Stopping The Engine

    STARTING/STOPPING THE ENGINE (1/3) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. Driver’s responsibility when parking or stopping the vehicle Never leave an animal,...
  • Page 112 STARTING/STOPPING THE ENGINE (2/3) Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out.
  • Page 113 STARTING/STOPPING THE ENGINE (3/3) If the RENAULT card is no longer in the When you leave your vehi- passenger compartment when you try cle, especially if you have to switch the engine off, the message your RENAULT card with “No keycard Press and hold” appears...

  • Page 114: Stop And Start Function

    STOP AND START FUNCTION (1/4) This system enables a reduced fuel For vehicles equipped with manual Before getting out of the consumption and lower greenhouse gearboxes: vehicle, you must switch gas emissions. The system is acti- – the gearbox is in neutral; off the ignition by pressing vated automatically when the vehicle is the engine stop (please see...
  • Page 115 STOP AND START FUNCTION (2/4) Preventing the engine from Conditions for coming out of Special note: depending on the vehi- cle, if you switch off the ignition when standing by engine standby the engine is on standby, the warning In certain situations, such as negotiat- For vehicles equipped with auto- Ä...
  • Page 116 Special case for vehicles with – for vehicles with automatic gear- boxes, the gradient is steeper than standby of the engine a RENAULT card approximately 12%; Certain conditions prevent the system With the engine on standby (traffic jam, – the “Clear View” function is activa- from using the engine standby function, traffic lights, etc.), if the driver unfas-...
  • Page 117 STOP AND START FUNCTION (4/4) Special feature of the automatic The system reactivates automati- engine re-start cally each time the vehicle is started using the start button (please refer Under certain conditions, the engine to “Starting, stopping the engine” in can restart on its own in order to gua- Section 2).

  • Page 118: Special Features Of Petrol Versions

    SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.

  • Page 119: Special Features Of Diesel Versions

    SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.

  • Page 120: Gear Lever

    GEAR LEVER Selecting reverse gear Vehicles with manual gearbox: follow the grid drawn on knob 1, and depend- ing on the vehicle, lift ring against the gear lever knob to select reverse. An impact to the under- side of the vehicle while Vehicle with automatic gearbox: refer manoeuvring (e.g.: strik- to the information on the “Automatic...

  • Page 121: Electronic Parking Brake

    ELECTRONIC PARKING BRAKE (1/3) Note: To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” ap- pears on the instrument panel: – with the engine running: when the driver’s door is opened; –...

  • Page 122: Manual Operation

    ELECTRONIC PARKING BRAKE (2/3) Special cases To park on a slope or while towing a trailer, for example, pull switch 2 for a few seconds to gain the maximum braking. To park the vehicle without applying the electronic parking brake (if there is a risk of freezing, for example): –...
  • Page 123 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults gearbox © – If there is a fault, the warning light illuminates on the instrument For safety reasons, automatic release panel accompanied by the “Check is deactivated when the driver’s door parking brake”...

  • Page 124: Driving Advice, Eco-Driving

    DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- Gear change indicator 2 cordance with a standard regulatory Depending on the vehicle, to obtain op- method. Identical for all manufactur- timum consumption levels, a warning ers, this enables vehicles to be com- light on the instrument panel lets you pared with one another.
  • Page 125 DRIVING ADVICE, ECO-DRIVING (2/5) An overall rating from 0 to 100 is dis- played to let you assess your eco driv- ing performance. The higher the rating, the lower the fuel consumption. Eco advice is given to help improve your performance. With your favourite journeys saved, you can compare your performance between trips and the performance of...
  • Page 126 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode Disabling the function Press switch 4. ECO mode is a function which opti- mises fuel consumption. This acts on The warning light goes out on all power consuming elements (engine the instrument panel to confirm deac- power, switching gears for vehicles tivation.
  • Page 127 DRIVING ADVICE, ECO-DRIVING (4/5) – Do not overrev the engine in the in- – Bad weather, flooded roads: termediate gears. You should always use the highest Do not drive through gear possible. floods if the water is – Avoid sudden acceleration. above the lower edge of –...
  • Page 128 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air conditio- ning, it is normal to observe an in- crease in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 129: Maintenance And Antipollution Advice

    MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life which will come nents with parts other than those origi- be replaced.

  • Page 130: Environment

    This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...

  • Page 131: Tyre Pressure Monitoring System

    TYRE PRESSURE MONITORING SYSTEM (1/3) Resetting the standard level Resetting procedure for the tyre pressures With the ignition on: – repeatedly and briefly press con- This should be done: trol 2 to select the tyre pressure dis- – when the standard tyre pressure play and the “Tyre pressure”...
  • Page 132 TYRE PRESSURE MONITORING SYSTEM (2/3) “Puncture” A wheel B is shown in red, the warning light 4 comes on, the message “Puncture” appears and there is a beep. This message appears along with the ® warning light. They indicate that the affected wheel is punctured or severely underinflated.
  • Page 133 Because the valves are specially de- or more wheels have been fitted with Please see the information on “Tyres” signed, only use equipment approved sensors not recognised by Renault. in Section 5. by the approved network. Please refer Contact an approved Dealer to fit new to “Tyre inflation kit”...

  • Page 134: Driver Correction Devices/Aids

    DRIVER CORRECTION DEVICES AND AIDS (1/12) ABS (anti-lock braking – ABS (anti-lock braking system) ; system) – ESC (electronic stability control) Under heavy braking, the ABS prevents with understeer control and trac- the wheels from locking, allowing the tion control; stopping distance to be managed and –...
  • Page 135 DRIVER CORRECTION DEVICES AND AIDS (2/12) Operating faults: © – lit up on the in- strument panel alongside mes- sages “Check ABS”, “Check braking system” and “Check ESC”: indicates the ABS, ESC and emergency brake assist are deactivated. Braking is always enabled;...

  • Page 136: Electronic Stability Control

    DRIVER CORRECTION DEVICES AND AIDS (3/12) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced un- ing fault the message “Check ESC”...

  • Page 137: Emergency Brake Assist

    DRIVER CORRECTION DEVICES AND AIDS (4/12) Emergency brake assist Braking anticipation Depending on the vehicle, when you This system supplements the ABS rapidly release the accelerator, the and helps reduce vehicle stopping dis- system anticipates the braking ma- tances. noeuvre in order to reduce stopping Operating principle distances.
  • Page 138 DRIVER CORRECTION DEVICES AND AIDS (5/12) Advanced traction control Activating or deactivating the Note: The system’s default mode is system “Auto” mode. If fitted on the vehicle, grip control From the multifunction screen, select makes it easier to control the vehicle on menu “Vehicle”, “Driving assistance”, low grip surfaces (soft ground, etc.).
  • Page 139 DRIVER CORRECTION DEVICES AND AIDS (6/12) If the driver depresses the brake pedal and the system still detects a risk of col- lision, the brake force is increased. If the driver fails to react following an alert of an imminent collision, the system activates the brakes.
  • Page 140 DRIVER CORRECTION DEVICES AND AIDS (7/12) Conditions for non-activation of the Operating faults system When the system detects an operating The system cannot be activated: fault, the warning light lights up – when the gear lever is in neutral; on the instrument panel, with the mes- –...
  • Page 141 DRIVER CORRECTION DEVICES AND AIDS (8/12) Active emergency braking This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs –...
  • Page 142 DRIVER CORRECTION DEVICES AND AIDS (9/12) Active emergency braking Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. –...
  • Page 143 DRIVER CORRECTION DEVICES AND AIDS (10/12) Driver assistance with a Operating principle trailer The function stabilises the vehicle by: This system helps to maintain control – asymmetric braking of the front over the vehicle while using a trailer. wheels to reduce shaking caused by It detects shaking caused by towing a the trailer;...
  • Page 144 DRIVER CORRECTION DEVICES AND AIDS (11/12) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards by au- tomatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
  • Page 145 DRIVER CORRECTION DEVICES AND AIDS (12/12) Operating faults © – If the warning light, together with the message “Check power steering”, is displayed on the instru- ment panel: please contact an au- thorised dealer. ® – If the warning light , together with the message “Power steering fault”, is displayed on the instrument...

  • Page 146: Lane Departure Warning

    LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
  • Page 147 LANE DEPARTURE WARNING (2/3) Conditions for non-activation of alerts – Indicators activated or having been activated less than approximately four seconds prior to departing from the lane; – Very fast lane departure; – Driving continuously on a line; – On bends, the function allows for slightly cutting the bend;...
  • Page 148 LANE DEPARTURE WARNING (3/3) Operating faults In the event of a malfunction, a mes- sage “Lane departure warning check” is displayed on the instrument panel, and the visibility indicators for the left and right lines disappear from the instru- ment panel. Consult an approved dealer.

  • Page 149: Blind Spot Warning

    BLIND SPOT WARNING (1/3) This system alerts the driver to other Activation/deactivation Special feature vehicles in the detection zone A. On the multifunction screen 2, select Make sure that the sensors are not obs- The system is activated when the vehi- the “Vehicle”...
  • Page 150 BLIND SPOT WARNING (2/3) Display B The function is activated and has not detected any vehicles. Display C Initial warning: the indicator light 4 shows that a vehicle has been detected in the blind spot. Display D When the direction indicator is activa- ted, the indicator light 4 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
  • Page 151 BLIND SPOT WARNING (3/3) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- Because sensors have played on the instrument panel. Consult been installed in the bum- an authorised dealer. pers, any work (repairs, re- placements, touching up of Note: When the engine is started, the paintwork) must be carried out by a...

  • Page 152: Safe Distance Alert

    SAFE DISTANCE ALERT (1/2) Using the sensor 1, this function noti- Activating/deactivating the fies the driver about the time interval function separating them from the vehicle in From the multifunction screen 2, select front, so they can respect a safe dis- menu “Vehicle”, “Driving assistance”, tance between the two vehicles.
  • Page 153 SAFE DISTANCE ALERT (2/2) – C (orange): the time interval falls between around 1 and 2 seconds (in- sufficient distance between the two This function is essential if adaptive vehicles); cruise control is activated. – D (red): the time interval is less than or equal to around one second (very insufficient distance between the two vehicles).
  • Page 154 CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) Switching on Press switch 1 on side . The indica- tor light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.

  • Page 155: Speed Limiter

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by It is possible to exceed the limit speed repeatedly pressing switch 2 : at any time. To do this: press the acce- lerator pedal firmly and fully (beyond –...
  • Page 156 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 3 (R). Putting the function on Switching off the function standby The speed limiter function is deactiva- ted if you press switch 1: in this case a The speed limiter function is suspended speed is no longer stored.
  • Page 157 OVERSPEED ALERT (1/3) Operating principle Special situations – If the vehicle is travelling in a coun- The system detects speed limit signs try where the speed units differ from on the side of the road and displays the those of the vehicle, the system dis- speed limit.
  • Page 158 OVERSPEED ALERT (2/3) Varying the limit speed If the speed limiter notification differs from the detected speed value, press and hold switch 4: – side a (+) to increase the notification speed to the detected speed; – side b (-) to reduce the notification speed to the detected speed.
  • Page 159 OVERSPEED ALERT (3/3) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
  • Page 160 CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to Controls Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- 1 Main “On/Off”...
  • Page 161 CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Activating cruise control At a steady speed (above approx. 20 mph or 30 km/h), press switch 2 side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control”...
  • Page 162 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While overtaking, the cruis- ing speed flashes red on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
  • Page 163 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 3 (R) if the vehicle speed is above 20 mph (30 km/h).

  • Page 164: Adaptive Cruise Control

    ADAPTIVE CRUISE CONTROL (1/7) When traffic conditions permit (large free-flowing road or motorway), the adaptive cruise control gives you the option of maintaining a chosen speed, known as cruise control, adjus- table from 30 mph to 90 mph (50 and 140 km/h), while keeping a following distance from the vehicle in front in the same lane.
  • Page 165 ADAPTIVE CRUISE CONTROL (2/7) Controls Switching on The cruising speed replaces the dashes and cruise control is confirmed by the Press switch 5. Indicator light 5 Main “On/Off” switch. appearance of the message “Adaptive comes on, lit green, and the message 2 Controls for: cruise ctrl”...
  • Page 166 ADAPTIVE CRUISE CONTROL (3/7) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, You can vary the following distance you may lift your foot off the accelera- from the vehicle in front at any time by tor pedal.
  • Page 167 ADAPTIVE CRUISE CONTROL (4/7) Putting the function on Returning to the cruising speed standby If a speed is stored, it can be recalled, once you are sure that the road con- The function is set to standby if: ditions are suitable (traffic, road sur- –...
  • Page 168 ADAPTIVE CRUISE CONTROL (5/7) Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate to reach this threshold. Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front, etc.), the system may not have time to respond and may emit a beep alongside the alert A when the situation...
  • Page 169 ADAPTIVE CRUISE CONTROL (6/7) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
  • Page 170 ADAPTIVE CRUISE CONTROL (7/7) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system.

  • Page 171: Parking Distance Control

    PARKING DISTANCE CONTROL (1/4) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to This function is an addi-...
  • Page 172 PARKING DISTANCE CONTROL (2/4) Note: the display 2 shows the vehicle Operation surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are before the side detection is activated. detected.
  • Page 173 PARKING DISTANCE CONTROL (3/4) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
  • Page 174 PARKING DISTANCE CONTROL (4/4) Automatic deactivation of the System sound parking distance control Enables the system sound to be se- lected from a choice of 3. The system deactivates: – when the vehicle speed is above ap- Deactivating the system sound proximately 6 mph (10 km/h);...

  • Page 175: Reversing Camera

    REVERSING CAMERA (1/2) Operation Fixed gauge 3 4 moving guide line: The fixed clearance gauge comprises This is shown in blue on the multifunc- When you change to reverse gear, the coloured markers A, B and C, indicat- tion screen 2. It indicates the vehicle camera 1 located on the tailgate pro- ing the distance behind the vehicle: trajectory according to the position of...
  • Page 176 REVERSING CAMERA (2/2) You can also adjust the camera image settings (brightness, contrast, etc.) The screen shows a reverse mirror Activating, deactivating the image. This function is an additional reversing camera The frames are a representation aid. It cannot, therefore, projected onto flat ground;...

  • Page 177: Assisted Parking

    ASSISTED PARKING (1/4) This function assists with parking ma- Switching on Special features noeuvres. With the vehicle stationary or driving Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. at less than 18.6 mph (30 km/h), press cated by arrows 3 are not obscured (by You only control the pedals and the switch 1.
  • Page 178 ASSISTED PARKING (2/4) Choice of manoeuvre Operation Your speed should not exceed around 4 mph (7 km/h). The system can perform four types of Parking manoeuvres: Once the warning light on the As long as the vehicle speed is less –...
  • Page 179 ASSISTED PARKING (3/4) Your speed should not exceed around In this case, the reason for suspending 4 mph (7 km/h). the manoeuvre will be displayed on the Once in position to exit the space, the multifunction screen. system will notify you of the end of the Make sure: manoeuvre.
  • Page 180 ASSISTED PARKING (4/4) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location.
  • Page 181 ADAPTIVE SUSPENSION Operating fault In the event of a fault, the system switches automatically to the “Neutral” mode in “Multi-Sense”. If the message “Check Damper control” appears on the instrument panel, con- sult an authorised dealer. Adaptive suspension makes it possible to modify the suspension automatically, according to driving conditions and to your driving style.

  • Page 182: Automatic Gearbox

    AUTOMATIC GEARBOX (1/6) Gear selector 3 position Grid B on the instrument grid A panel 1: selector rest position – The current gear is given in zone 5; 2: button P: Park – The available functions are provided in the ambient colour chosen by the R: reverse driver;...
  • Page 183 AUTOMATIC GEARBOX (2/6) To disengage position P To engage neutral (button 2) With the vehicle at a standstill, engine running, depress the brake pedal and With the vehicle at a standstill, engine move the selector 3 to the left: running, depress the brake pedal and move the selector to the desired posi- –...
  • Page 184 AUTOMATIC GEARBOX (3/6) Driving in automatic mode To select reverse gear Economical driving When driving, always leave the lever With the vehicle at a standstill, engine With the vehicle at a standstill, engine in position D, keeping the accelerator running, position P, N or R, depress the running, position P, N or D, depress the pedal lightly depressed to ensure auto- brake pedal and move the selector to...
  • Page 185 AUTOMATIC GEARBOX (4/6) Driving in manual mode The system will take over once this period has elapsed and may then trig- Driving in temporary manual mode ger an automatic gear change. Temporary manual mode can only be Likewise, to prevent incorrect manoeu- selected when automatic mode D has vres, a gear change may be refused been engaged and the vehicle speed...

  • Page 186: Parking The Vehicle

    AUTOMATIC GEARBOX (5/6) Special cases Special cases With the engine running, the automatic In certain driving cases (eg: protect- gearbox in D or R or N or M and with- As position P is automatically en- ing the engine), a gear change can be out your foot on the brake, messages gaged when the engine is stopped, it is performed automatically in the event of...
  • Page 187 AUTOMATIC GEARBOX (6/6) Special circumstances Operating faults – If the bends and road surface – When driving, if the “Check auto do not allow you to stay in auto- gearbox” message appears on the matic mode (e.g. in the mountains), instrument panel, it indicates a fault.
  • Page 188 2.80...

  • Page 189: Your Comfort

    Section 3: Your comfort multi-Sense ..............Air Vents .

  • Page 190: Multi-Sense

    MULTI-SENSE (1/2) Mode Eco The Multi-Sense system enables once Multi-Sense of five modes to be selected which, de- Mode Eco is geared towards saving Sport pending on the vehicle, affect the drive, energy and the environment. The sus- the light environment, the comfort and Neutral Comfort Perso...

  • Page 191: Sport Mode

    MULTI-SENSE (2/2) Sport mode This mode allows greater responsive- ness from the engine and gearbox, making the suspension and steering firmer. Mode Perso This mode enables you to manually configure the drive, light environment and, depending on the vehicle, the comfort and engine noise.

  • Page 192: Air Vents

    AIR VENTS: air outlets (1/3) 1 left-hand air vent 2 windscreen demisting vents 6 2nd row passenger air vent 3 centre air vents 7 3rd row passenger air vent 9 Additional air conditioning control 4 side window demister outlets 8 passenger footwell heater outlets 10 multifunction screen 5 right-hand air vent...

  • Page 193: Front Seats

    AIR VENTS: air outlets (2/3) Front seats To remove bad odours from your ve- hicles, only use the systems designed Direction for this purpose. Consult an approved Dealer. Right/left: turn knob 2. To fully close, turn beyond the point of resistance.
  • Page 194 AIR VENTS: air outlets (3/3) 2nd row rear seats 3rd row rear seats Right/left direction Right/left direction Move air vent 4. Move air vent 6. Up/down direction Front/rear direction Move cursor 3. Move cursor 5.

  • Page 195: Automatic Climate Control

    AUTOMATIC CLIMATE CONTROL (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
  • Page 196 AUTOMATIC CLIMATE CONTROL (2/5) Note: The air conditioning configura- tion depends on the mode selected on the “Multi-Sense” menu (please refer to the information in “Multi-Sense” in Section 3). The displayed temperature values Varying the ventilation speed Temperature adjustment show a comfort level. There are two types of settings: In automatic mode, the system uses –...
  • Page 197 AUTOMATIC CLIMATE CONTROL (3/5) To exit this function, press either: – button 4; – again button 6; – on button 8, 9 or 10. Clear View function Press button 6 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 3 to stop the heated rear ices the windscreen, the rear screen, screen operating, and the integrated in-...
  • Page 198 AUTOMATIC CLIMATE CONTROL (4/5) Rear screen de-icing/ demisting Press button 3 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 3 again.

  • Page 199: Air Recirculation

    AUTOMATIC CLIMATE CONTROL (5/5) Automatic usage Press button 16 (a warning light comes on in zone 14). Manual use Press button 5 to force air recirculation. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows.
  • Page 200 ADDITIONAL AIR CONDITIONING (1/2) Control The air conditioning system is used for: – lowering the temperature inside the The additional air conditioning powers passenger compartment; the air vents 3 in the third row to add to the heating level of the second and –...

  • Page 201: Switching On Or Off

    ADDITIONAL AIR CONDITIONING (2/2) Switching on or off Mode MANUAL FAST:Turn the control to 10. Enables the system to reach the de- Press button 7 to activate. The rear From the multifunction screen, press sired comfort level more quickly. control 2 is then operational and the button 4.

  • Page 202: Air Conditioning: Information And Advice On Use

    AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.

  • Page 203: Outside Air Quality And Deodorisation Functions

    OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Take care Deodorization cycle With the air conditioning switched Deodorisation function on, from the screen A, select Menu, This reduces unpleasant odours in the Vehicle, Take care. passenger compartment. Outside air quality Deodorization cycle –...

  • Page 204: Electric Windows

    6. Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while. They may pose a risk to themselves or to others by starting the engine or activating equip- ment (such as the gear lever or electric windows).
  • Page 205 ELECTRIC WINDOWS (2/2) Remote control window Operating faults One-touch mode closing This mode works in addition to the ope- In case of a fault when closing a (vehicles with 4 one-touch electric win- ration of the electric windows described window, the system reverts to normal dows).

  • Page 206: Electric Sunroof

    Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-suffi- cient or a pet, even for a short while.
  • Page 207 RENAULT,, the windows and the elec- Before using the sunroof, check the tric sunroof will close automatically. After closing the sunroof by remote...

  • Page 208: Fixed Glass Roof

    ELECTRIC SUNROOF /FIXED GLASS SUNROOF (3/3) If the blockage persists, keep switch 2 pressed until it closes completely. Please consult an authorised dealer. Operating fault Fixed glass roof – If the sunroof will not close, turn Opening the blind switch 2 to position B to open the Press the top of handle 4.

  • Page 209: Interior Lighting

    INTERIOR LIGHTING (1/2) Map reading lights From the multifunction screen, it is pos- sible to deactivate/activate the cour- Press switch 1 to get: tesy lights upon opening the doors or – permanent lighting; the boot. To do this, please refer to “Vehicle settings customisation menu”...
  • Page 210 INTERIOR LIGHTING (2/2) Door lights Storage drawer light Boot lights Light 2 comes on when the door is Light 3 comes on when the storage Light 4 comes on when the boot is opened. drawer is opened. opened. 3.22...

  • Page 211: Sun Visor/Blinds

    SUN VISOR, BLINDS Front sun visor Lateral sun visor Lower the sun visor 1 on the wind- Pull the sun visor up by tab 4 until screen or unclip it and lower it over the hooks 5 engage in their housings (make side window.

  • Page 212: Passenger Compartment Storage/Fittings

    PASSENGER COMPARTMENT STORAGE/FITTINGS (1/5) Door pockets 1 Dashboard storage Passenger storage drawer 3 compartment 2 To open, move your fingers into area 4- It can hold a 1.5 litre bottle. it will open by itself. If on a steep slope, assist the drawer opening by pulling handle 5.
  • Page 213 PASSENGER COMPARTMENT STORAGE/FITTINGS (2/5) Cup holders 6 and 9 Storage compartments 8 Central storage and 10 compartment 11 Storage compartment 7 Slide the curtain 12 to open the storage compartment. Depending on the vehicle, this may be used to hold a removable cup-holder. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged.
  • Page 214 PASSENGER COMPARTMENT STORAGE/FITTINGS (3/5) Centre console storage Grab handle 15 compartment 14 This offers support and can be held when the vehicle is being driven. Lift up the armrest 13. Do not use it for getting into or out of the vehicle.
  • Page 215 PASSENGER COMPARTMENT STORAGE/FITTINGS (4/5 Rear door storage Storage drawer 18 under the Front seat storage pockets 19 compartment 17 centre console Nothing should be placed Ensure that no hard, heavy on the floor area in front of or pointed objects are the driver as such objects placed in the “open”...
  • Page 216 PASSENGER COMPARTMENT STORAGE/FITTINGS (5/5) Rear parcel shelf 20 Flap under the feet of the right rear passenger 21 This location houses the tool kit. Please refer to the information on “Tools” in Section 5. 3.28...

  • Page 217: Accessories Socket

    ASHTRAY/CIGAR LIGHTER/ACCESSORIES SOCKET Ashtray location 1 Accessories sockets You can use the one of sockets 2. Cigarette lighter 2 They are provided for connecting ac- cessories approved by our Technical With the ignition on, push in the ciga- Department. rette lighter 2 - it will spring back with a click when it is ready.

  • Page 218: Rear Headrests

    REAR HEADRESTS Position for use Centre seat headrest 2 storage position Lift the headrest to maximum height, then lower it until it locks. Press tab 1 and lower the headrest completely. To remove the headrest When the headrest is set at the lowest position, this is for storage Press the tab(s) 1, then remove the only.
  • Page 219 REAR SEATS (1/5) Heated seats (depending on vehicle) Side seats only With the ignition on: – Pressing the switch 3 on the requi- red seat for the first time activates the heating system on high. Both in- tegrated switch warning lights come –...
  • Page 220 REAR SEATS (2/5) When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or leg, a pet, gravel, cloth, toys, etc.). To access the third row rear seats To unfold a seat in the third row When moving the rear –...
  • Page 221 REAR SEATS (3/5) Disabling the function – With the engine running, a buckled seat belt prevents the movement of the relevant seat. – Once the vehicle is moving the two controls are deactivated. To automatically fold down Conditions of use the seats (flat position) With the vehicle at a standstill and the rear seat belts unlocked:...
  • Page 222 REAR SEATS (4/5) Encountering an obstacle One-touch folding While being moved, if a seat encoun- ters an obstacle, the movement stops of its own accord. You will then have to manually fold back the seat after re- moving the obstacle. Operating fault If all user conditions have been ful- filled and the folding action still fails to...
  • Page 223 REAR SEATS (5/5) Use restriction It is not permitted to drive with a second row rear seatback or seat folded down when there is a passenger occupying a third row rear seat. For safety reasons, carry out any adjustments when When refitting the seat- the vehicle is not being back, make sure it is cor-...

  • Page 224: Luggage Compartment

    TAILGATE Manual controls Opening the doors manually – slide the tab 5 to the right in vehicles with a manual tailgate, or tab 4 on from the inside To open vehicles with an automatic tailgate. If it is impossible to unlock the tailgate, Press button 1 and lift the tailgate.

  • Page 225: Automatic Tailgate

    – using the RENAULT card remote tailgate. control; – In the event that the battery is dis- – using the controls on the tailgate;...
  • Page 226 With the ignition off, press and hold Press control 2. Press control 3. switch 1 on the RENAULT card. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. Risk of injury.
  • Page 227 (a beep is emitted every second). while you have your hands full. Start function). With the RENAULT card on your person – The hands-free feature may not and with the ignition off, perform a for- work if the vehicle is equipped with...

  • Page 228: Obstacle Detection

    AUTOMATIC TAILGATE (4/5) Stopping the tailgate Obstacle detection manoeuvre When the tailgate window encounters an obstacle (presence of an object or The automatic tailgate manoeuvre can person) when it is moving, it stops. be stopped at any time by a short press Depending on the opening position, the on one of the controls.
  • Page 229 AUTOMATIC TAILGATE (5/5) Precautions during use Operating faults Before opening/closing the tailgate, If you activate the automatic tailgate ensure that the surrounding space is continuously for around a minute (se- sufficient to allow the tailgate to ope- quence of opening and closing), it will rate.

  • Page 230: Luggage Cover

    LUGGAGE COMPARTMENT COVER To remove the flexible Refitting the luggage Luggage compartment cover section of the luggage cover compartment cover storage Pull handle 1 gently to release the pins Place the luggage cover into the hous- Vehicles without additional air con- from their mounting points located on ing points 3.
  • Page 231 BOOT STORAGE SPACE AND FITTINGS Bag hooks 1 Storage compartment under boot false floor Maximum weight per hook: 5 kg. Depending on the vehicle, to access, lift the false floor of the boot 5 using the handle 2. The false floor can be attached using the hook 4 in the housing 3.

  • Page 232: Transporting Objects

    TRANSPORTING OBJECTS IN THE BOOT Always place the objects to be trans- Anchorage points ported so that their largest side rests Hooks 1 located on each corner of the against the back of the rear seat for boot allow the load to be secured. normal loads (e.g.: A), or against the Always position the hea- back of the front seats B when the rear...

  • Page 233: Equipment

    TRANSPORTING OBJECTS towbar A: 1066 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Vehicle fitted with an au- tomatic tailgate with the Choice and fitting of towing «hands-free»...

  • Page 234: Luggage Net

    LUGGAGE NET (1/2) Depending on the vehicle, this may be Fitting the luggage net – attach the two hooks 5 for the net used when transporting animals or lug- straps 3 to the anchoring points 4 behind the front seats gage to isolate them from the passen- –...
  • Page 235 LUGGAGE NET (2/2) Fitting the luggage net – fix the net belt hook 11 onto the an- choring points 10; behind the rear seats (behind the second row rear seats on – adjust net strap 9 so that it is taut. the 7-seater version) –...

  • Page 236: Roof Bars

    ROOF BARS Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.

  • Page 237: Multimedia Equipment

    MULTIMEDIA EQUIPMENT (1/2) Multimedia systems Hands-free telephone integrated control 1 Multimedia touchscreen display; 2 Central control; For equipped vehicles, use the steering 3 Steering column controls; wheel controls 4. 4 Steering wheel controls; 5 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
  • Page 238 MULTIMEDIA EQUIPMENT (2/2) Multimedia sockets 7 Sockets USB can only recharge acces- sories with a maximum power rating of 12 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. The JACK socket enables the radio to be used with an auxiliary cable.
  • Page 239 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .

  • Page 240: Bonnet

    BONNET (1/2) To open, pull handle 1, located on the Unlocking the bonnet catch left-hand side of the dashboard. To unlock, push tab 3 at the same time When working in the engine as opening the bonnet. compartment, ensure that the windscreen wiper stalk Opening the bonnet is in the park position.

  • Page 241: Closing The Bonnet

    BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.

  • Page 242: Engine Oil Level: General Information

    ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level In order to prevent splashback, it is between oil changes. recommended that a funnel be used However, contact your approved Dealer when topping up/filling with oil...

  • Page 243: Engine Oil Level: Topping Up/Filling

    ENGINE OIL LEVEL: topping up, filling (1/2) Topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...

  • Page 244: Oil Change

    ENGINE OIL LEVEL: topping up, filling OIL CHANGE (2/2)/ Oil change Engine oil grade Service interval: refer Refer to the Maintenance Service Maintenance Service Booklet for your Booklet for your vehicle. vehicle. Oil change capacity Filling: take care when Please refer to the maintenance docu- topping up the oil that ment for your vehicle, or contact an au- no oil drips onto engine...

  • Page 245: Levels

    LEVELS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...

  • Page 246: Brake Fluid Level

    LEVELS (2/3) Level 2 Topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the “MINI” warning Only use fluids approved by our line.

  • Page 247: Windscreen/Headlight Washer Reservoir

    LEVELS /FILTERS (3/3) Filters Liquid Windscreen washer fluid. In winter, use The replacement of filter elements (air anti-freeze product. Use products rec- filter, passenger compartment filter, ommended by an authorised dealer. diesel filter, etc.) is scheduled in the maintenance operations for your vehi- Note: Do not use pure water (risk of cle.

  • Page 248: Battery

    BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine and the message on the instrument panel will disappear. The charge status of your battery can decrease especially if you use your vehicle:...
  • Page 249 BATTERY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 eye protection required; –...

  • Page 250: Tyre Pressure

    TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure monitoring system In cases of under-inflation (puncture, low pressure, etc.), warning light lights up on the instrument panel. Please refer to the information on the “Tyre pressure monitoring system” in Section 2. Vehicle used fully laden (Maximum Permissible All-up Weight) and towing a trailer...
  • Page 251 TYRE PRESSURES (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...

  • Page 252: Bodywork Maintenance

    BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
  • Page 253 BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...

  • Page 254: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, mul- larly.
  • Page 255 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
  • Page 256 4.18...

  • Page 257: Practical Advice

    RENAULT card: battery ........

  • Page 258: Puncture/Emergency Spare Wheel

    PUNCTURE, EMERGENCY SPARE WHEEL (1/3) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function Disable the «hands-free» function before washing the vehicle manually does not check the emergency spare or handling the emergency spare wheel or the towbar.
  • Page 259 PUNCTURE, EMERGENCY SPARE WHEEL (2/3) Emergency spare wheel – only use the wheel brace 4 (using a different tool could damage the It is located under the vehicle. mechanism) to unroll the retaining From the boot: cable, and the wheel falls to the ground.
  • Page 260 PUNCTURE, EMERGENCY SPARE WHEEL (3/3) To refit a wheel Reposition the blanking cover then the cover 3. To carry out this operation, the cable For vehicles fitted with a servo, replace must be unwound. the servo 2. Tighten the three screws 1. Stand the wheel up with the valve to- wards you.
  • Page 261 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved inflation kit if the tyre has for inflating the tyres of the been damaged as a result vehicle originally equipped of driving with a puncture. with the kit.
  • Page 262 TYRE PRESSURE KIT (2/3) – end piece 3 must be connected to a vehicle accessories socket; – press switch 5 to inflate the tyre to the recommended pressure (please refer to the information on “Tyre in- flation pressure” in Section 4); –...
  • Page 263 TYRE PRESSURE KIT (3/3) Precautions when using the Once the tyre is correctly inflated, remove the kit: slowly unscrew the in- flation adapter 2 to prevent any repair The kit should not be operated for more product from escaping and store the than 15 consecutive minutes.

  • Page 264: Tools

    TOOLS (1/2) Jack 3 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned 4). Hubcap tool 5 This tool is used to remove the wheel trims. Tow eye 6 Refer to the information on “Towing” in Section 5.
  • Page 265 TOOLS /WHEEL TRIM (2/2) Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then posi- Wheel trim tion it correctly in its housing: risk of Remove it using the hubcap tool 5 by injury.

  • Page 266: Changing A Wheel

    CHANGING A WHEEL (1/2) Vehicles equipped with a jack and wheelbrace If necessary, remove the wheel trim. Use the wheelbrace 2 to slacken off the wheel bolts. Position it so as to be able to push from above. Open the door nearest the wheel concerned to identify the arrow 1 indi- cating the jacking point 3.
  • Page 267 CHANGING A WHEEL (2/2) Turn the wheelbrace until the wheel lifts off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub.

  • Page 268: Tyres (Tyre And Wheel Safety, Use In Winter)

    TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will tial to keep them in good condition. become visible 2: it is then necessary to replace your tyres because the tread You must make sure that your tyres rubber is now only 1.6 mm deep at...

  • Page 269: Tyre Pressures

    TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a In cases of under-inflation (puncture, the emergency spare wheel).
  • Page 270 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- For safety reasons, this op- chains to the rear axle is strictly for- sary to observe the speed specified by eration must be carried out...

  • Page 271: Direction Indicators

    FRONT HEADLIGHTS: changing bulbs Main beam headlights 2 Cleaning the headlights Please consult an authorised dealer. Use a soft cloth. If this does not clean it properly, moisten the cloth with soapy water then rinse off. Dipped beam headlights 3 Finally, carefully dry off with a soft dry Please consult an authorised dealer.

  • Page 272: Rear Lights (Changing Bulbs)

    REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/3) Side lights, brake lights and Reversing lights From the outside of the vehicle, pull on the light unit to remove it then unscrew direction indicators From the boot, unclip the cover on the bulb holder 3 a quarter of a turn.
  • Page 273 REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/3) Fog light High level brake light 5 Access bulb holder 4 via the under- Consult an approved Dealer. neath of the vehicle, then unscrew it by turning towards the centre of the vehi- cle.
  • Page 274 REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/3) Number plate lights 6 Side indicator lights 8 Unclip light 6 by pressing the tab 7. Consult an approved Dealer. Remove the light cover to gain access to the bulb. Bulb type: C5W festoon bulb. 5.18...
  • Page 275 INTERIOR LIGHTING: changing bulbs (1/2) Map reading lights 1 Front and rear door lights 2 Please consult an authorised dealer. Unclip door light (using a flat-blade screwdriver or similar) 2. Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: W5W.

  • Page 276: Ambient Lighting

    INTERIOR LIGHTING: changing bulbs (2/2) Boot lights 3 Passenger storage drawer Ambient lighting light 4 Unclip light 3 by pressing the tabs on Please consult an authorised dealer. each side (using a flat-blade screw- Unclip light 4 by pressing the tabs on driver or similar).

  • Page 277: Fuses

    FUSES (1/2) Use the fuse allocation label in storage compartment A to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label. Fuse box Tweezers 1 If any electrical component does not...
  • Page 278 FUSES (2/2) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Windscreen washer Not used Third row accessories socket, boot accessories Towbar socket ë Ý socket Front cigarette lighter, front and rear second row Diagnostic socket, audio alarm Æ...

  • Page 279: Connecting A Battery Charger

    BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
  • Page 280 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.

  • Page 281: Battery

    RENAULT lock/unlock the vehicle (please refer to Note: it is not advisable to touch the card: the information on “Locking/unlocking...

  • Page 282: Accessories

    ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.

  • Page 283: Windscreen Wiper Blades

    WINDSCREEN WIPER BLADES: replacement (1/2) With the ignition on, return the wind- screen wiper stalk to the stop position. The blade on the driver’s side must always be above the passenger blade. If this is not the case, a quick sweep of the windscreen wipers should be per- formed once the vehicle is travelling at over 4 mph (7 km/h).
  • Page 284 WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; –...
  • Page 285 TOWING: breakdown (1/2) Before towing, put the gearbox in neu- The speed specified by current legis- tral, unlock the steering column and re- lation for towing must always be ob- lease the parking brake. served. If your vehicle is the towing For vehicles fitted with an automatic vehicle, do not exceed the maximum gearbox, if it is not possible to put the...
  • Page 286 TOWING : breakdown (2/2) Use only towing hitch 3 and the wheel- brace or the lever located under the 2nd row right rear passenger footwell (please refer to the information on the “Tool kit” in Section 5). – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed...

  • Page 287: Operating Faults

    OPERATING FAULTS (1/6) Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...
  • Page 288 Starting conditions are not ful- Please refer to the information on “Starting, stopping filled. the engine” in Section 2. The RENAULT “hands-free” card Please refer to the information on “Starting, stopping does not work. the engine” in Section 2. The engine cannot be switched off.
  • Page 289 OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
  • Page 290 OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
  • Page 291 OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
  • Page 292 OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights. Traces of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the...

  • Page 293: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Engine identification plates .

  • Page 294: Vehicle Identification Plates

    VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MMAC (Maximum permissible hicle identification plate should be all-up weight). quoted on all correspondence or 5 MTR (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MMTA (Maximum Permissible The presence and location of the in- Weight) front axle.

  • Page 295: Engine Identification Plates

    ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 296: Dimensions

    DIMENSIONS (in meters) 1,034 2,884 0,939 1,624 to 1,634 4,857 1,677* 1,615 to 1,625 2,128 * Unladen...

  • Page 297: Engine Specifications

    ENGINE SPECIFICATIONS Versions 1.6 Tce 1.6 dCi Engine type M5M Turbo (see engine plate) Cubic capacity (cc) 1 618 1 598 Type of fuel It is essential that you use unleaded petrol of the Diesel Octane rating octane rating stated on the label inside the fuel The label located in the fuel filler flap filler flap.

  • Page 298: Weights

    WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. Consult an approved Dealer. Maximum Permissible All-Up Weight (MMAC) Weights are indicated on the vehicle identification plate (refer Gross Train Weight (MTR) to the information on “Vehicle identification plates”...

  • Page 299: Replacement Parts And Repairs

    REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

  • Page 300: Service Sheets

    SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 301 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 302 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 303 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 304 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 305 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...

  • Page 306: Anticorrosion Check

    ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
  • Page 307 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
  • Page 308 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
  • Page 309 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
  • Page 310 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...

  • Page 311: Alphabetical Index

    ALPHABETICAL INDEX (1/5) bulbs ABS ...............2.26 → 2.37 changing ............5.15 → 5.18 accessories................ 5.26 accessories socket ........... 3.29, 3.50 catalytic converter........... 2.10 – 2.11 adaptive cruise control...........2.56 → 2.62 central door locking ........1.8 → 1.10, 1.14 additional air conditioning ........3.12 – 3.13 changing a bulb .............5.15 →...
  • Page 312 ALPHABETICAL INDEX (2/5) driver’s position .............1.58 → 1.65 oil filter ................4.9 driving ..2.2 → 2.5, 2.10 → 2.20, 2.23 → 2.37, 2.46 → 2.48, passenger compartment filter ........4.9 2.52 → 2.66, 2.74 → 2.79 fittings ..............3.24 → 3.28 driving aids ............2.26 →...
  • Page 313 ALPHABETICAL INDEX (3/5) head-up display .............1.66 → 1.69 lifting the vehicle headlight flashers .............. 1.85 changing a wheel ..........5.10 – 5.11 headlight washer ............... 1.95 lighting: headrest................3.30 exterior ............1.3, 1.86 → 1.90 heating and air conditioning system ....... 3.13 – 3.14 instrument panel ............
  • Page 314 ............ 2.67 – 2.68 starting the engine .............2.3 → 2.5 rear view mirrors ............1.82 → 1.84 steering wheel RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 adjustment ..............1.34 RENAULT card Stop & Start ...............2.6 → 2.9 battery ................5.25 Stop &...
  • Page 315 ALPHABETICAL INDEX (5/5) sun visor ................3.23 trip computer and warning system... 1.60 → 1.65, 1.70 → 1.79 sunroof..............3.18 → 3.20 tyre inflation kit............5.5 → 5.7 suspension ................ 2.73 tyre pressure......2.23 → 2.25, 4.12 – 4.13, 5.13 suspension with controlled damping........2.73 tyre pressure monitor..........2.23 →...
  • Page 318 à999105939Rí í î ä J1 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents