Mitsubishi Electric SLZ-A09AR Operation Manual page 4

2. Operation
ON/OFF
AUTO COOL
HEAT DRY
MODE
For SLZ-A09/A12/A18AR
A
ON/OFF
1
AUTO COOL
HEAT DRY
MODE
For SLZ-A09/A12/A18AR
A
ON/OFF
AUTO COOL
HEAT DRY
1
MODE
For SLZ-A09/A12/A18AR
A
ON/OFF
AUTO COOL
HEAT DRY
MODE
For SLZ-A09/A12/A18AR
4
A
TOO TOO
WARM COOL
1
FAN SELECT
VANE TIME
RESET
TOO TOO
WARM COOL
FAN SELECT
VANE TIME
RESET
TOO TOO
WARM COOL
FAN SELECT
VANE TIME
RESET
B
h
TOO TOO
WARM COOL
FAN SELECT
1
VANE TIME
2
RESET
2.5. Selecting a temperature
s s s s s To decrease the room temperature:
TOO
1Press button to set the desired temperature.
WARM
A The selected temperature is displayed.
• Each time you press the button, the temperature value decreases by 1 °C.
s s s s s To increase the room temperature:
TOO
1Press button to set the desired temperature.
COOL
A The selected temperature is displayed.
• Each time you press the button, the temperature value increases by 1 °C.
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C
Heating: 17 - 28 °C
Automatic: 19 - 28 °C
2.6. Selecting a fan speed
FAN
1Press
button to select a desired fan speed.
• Each time you press the button, available options change with the dis-
play A on the remote controller, as shown below.
Remote controller display
Fan speed
Low
M
3-stage
In the following situations, the display differs from the fan speed of the unit.
• In the case of DEFROST/STAND BY lamp lighting of the unit.
• Just after the heating mode (while waiting to change to another mode).
• When the temperature of the room is higher than the temperature set-
ting of the unit operating in the heating mode.
• In drying mode, the indoor fan sometimes stops.
2.7. Adjusting vertical airflow direction
The vertical air vane helps select the vertical direction of the airflow.
1Press button to select the vertical airflow direction.
VANE
A Each time you press the button, the option changes are displayed on
the remote controller, as shown below.
→ 2 → 3
1
s
1 Horizontal airfrow 30°
2 Downword airfrow 45°
3 Downword airfrow 55°
• In either cooling or drying mode, if you select 2 or 3 or 4 when the fan
speed is Low or Medium, the airconditioner will switch automatically to
Horizontal airflow 1 mode after one hour.
In the following situations, the display differs from the vertical airflow direc-
tion of the unit.
• In the case of DEFROST/STAND BY lamp lighting of the unit.
• When the temperature of the room is higher than the temperature set-
ting of the unit operating in the heating mode.
2.8. Using the timer
It is convenient to set the timer when you go to bed, when you get home,
when you get up, etc.
1Select the timer mode by pressing the
A Each time this button is pressed, the timer mode is changed in se-
quence:
(OFF TIMER)
2Set the time of the timer using the
B Each time this button is pressed, the set time increases by 1 hour to
12 hours.
To release the timer:
SELECT
• Press the button until
are not displayed.
Note:
The OFF TIMER and the ON TIMER cannot be set at the same time.
Medium High
→ 4 → 5
4 Downword airfrow 70°
5 Swing
SELECT
button during operation.
(ON TIMER) TIMER RELEASE
TIME button.
(OFF TIMER) and (ON TIMER)