Drainage; Programming The Machine; Selecting The Language; Water Hardness Adjustment - Gaggia Syncrony Digital DM1075 User Manual

15
ment lever (17), positioning it on point 5 of the
scale.
Never fill the coffee bean container with other
products. They might damage the machine!
Before filling the container with coffee beans,
make sure the pre-ground coffee container is
closed to prevent coffee beans from falling into
it. They might damage the machine!.
26
Remove the water tank (11) from the machine,
remove its cover (12) and fill it with cold water
(approx. 2.4 l). A valve on the tank bottom
prevents water from escaping.
Before installing the water tank in the
machine, make sure the coffee bean
container cover is properly fitted.
Install the water tank, slightly pressing over it to
fit the valve which will open automatically.
Replace the cover on the tank.
Do not fill the tank with an excessive quantity of
water.
Always fill the tank with fresh water: hot water
as well as other fluids might damage the tank.
Do not switch on the machine if the water tank
is empty. Before using the machine make sure
there is enough water in the tank.
Connect the plug to the socket and press the
main switch.

DRAINAGE

The display shows
"WARMING UP "
Should
"ENERGY "
"SAVING "
(1/2) be displayed, press the Energy saving
switch to disactivate the energy saving mode.
Drainage
Direct the steam/hot water dispensing tube (7)
over the drip tray (2). Place a cup or another
suitable container under the dispensing tube,
then turn the steam/hot water knob (9)
counterclockwise. The pump starts automati-
cally. Wait until a regular water jet is obtained,
then close the knob. The machine is now
drained and ready to work.
The display shows
"ECONOMIE "
"ENERGIE "
Important: It is advisable to drain the ma-
chine before the first start, after a prolonged
period the machine has not been used or
whenever the water tank has been completely
emptied. Furthermore, should the pump be
defective, the display shows
"VENTILATE "
Programming
the coffee machine
27
To enter the programming mode, press the key
ENT (pre-ground coffee) when the machine is
on and keep it pressed until the first two lines of
16
the programming mode are displayed:
"LANGUAGE "
"RINSING "
At the end of the line appears a blinking
asterisk, which can be moved up and down
with the keys (tall and regular coffee).
The display shows the following items in this
sequence:
LANGUAGE PREGRINDING
RINSING TOTAL COFFEES
WATER HARDN. DESCALING
CUP HEATER SIGNAL. DESCAL.
TEMPERATURE TIMER
PREBREWING RINSING CYCLE
Then, press ESC. The machine is now in the
normal mode again.
Selecting menu items
Select the different menu items by means of the
keys . The key ent allows you to
activate the selected item. It is possible to
modify the selected figures in a menu item using
the keys . The key ent memorizes the
selected options, for instance ON for the item
cup heater.
Should you accidentally change some data,
press esc to leave the menu item without saving
the new options which were selected acciden-
tally.

Selecting the language

Move the asterisk at the end of the line to the
menu item LANGUAGE using the keys .
Press ent to activate this item.
SELECTING THE LANGUAGE
The display shows:
"LANGUAGE "
"ENGLISH "
The keys allow you to change the set
options: Deutsch, italiano, français, english,
español, portugues.
Rinsing cycle function
If the rinsing cycle function is activated, the
machine that is started after a period of inactiv-
ity starts a water rinsing cycle to the coffee
dispensing units automarically.
Move the asterisk to the menu item RINSING CYCLE
using the keys und press ENT to active it.
The display shows:
"RINSING "
"ON "
You can modify the chosen item with the
key : on; off.

Water hardness adjustment

In order to adjust the water hardness, it is
necessary to test the water using the strip
supplied with the machine. Dip the strip into the
water for a second, shake off excess water
gently, wait approx. 1 minute and read the
results.
Move the asterisk at the end of the line to the
menu item WATER HARDN. using the keys
. Press ent to activate this item.
The display shows:
"WATER HARDN "
"HARDNESS 2 "