Alignment Procedure - Daewoo 531X-3 Service Manual

ICON CONTROL
Adjust the position of the display horizontally (left or right) .
H. CENTER
Adjust the position of the display vertically (up or down)
V. CENTER
H. SIZE Adjust the width (horizontal size) of the display.
V. SIZE
Adjust the height (vertical size) of the display.
FUNCTIONS
.
12

ALIGNMENT PROCEDURE

Standard Adjustment Conditions
1. Power source voltage : 100-240Vac 50/60Hz
2. Aging : Take at least 20 minutes warm-up time.
3. Signals
Video : Analog 0.7Vpp 75Ω terminal positive polarity
Synchronizing : TTL level Negative/Positive Separate
Deflection frequency
Horizontal Frequency : 30KHz - 54KHz(30~70KHz)
Vertical Frequency : 50Hz - 160Hz
Pre-Adjustment
1. B+ Adjustment
Adjust 25KV dc between anode cap and ground at a cross hatch pattern of 54KHz(68KHz) by using
the factory mode.
Method to launch the factory mode
Step 1. Turns off the monitor.
Step 2. Push the brightness up button and then push the power button at once.
Main Adjustment
1. Setting the Controls
Set the value of items as following.
Contrast : Max.(OSD value up to MAX)
Brightness : Center(Set the OSD value to center)
2. H.size, V.size, H.center, V.center, Pin Balance, Pincushion, Trapezoid, Parallelogram.
Receive the cross hatch pattern of Factory preset mode.
H.size, V.size, H.center, V.center, Pin Balance, Pincushion, Trapezoid are adjusted at each mode.
In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode has it's
own value according to each control.
3. Focus
(a) Set brightness control to center and contrast control to MAX.
(b) Receive all "H" character pattern of 1024 x 768(48KHz@60Hz) or 1024 x 768(68KHz@85Hz)
(c) Adjust the Focus control of FBT to obtain best Focus.
4. Geometric Distortion Adjustment.
(a) Receive the cross hatch pattern of factory preset mode.
(b) Pincushion, Trapezoid, Pin Balance, Parallelogram.
5. White Balance Adjustment
(a) Select 9300°K on the OSD Menu.
(b) Receive a full white pattern of 54KHz or 68KHz mode signal by using the signal generator.
(c) Set the brightness control to the maximum, the contrast control to the maximum.
(d) Cut off the FBT screen VR.
(e) Receive all the black patterns. The luminance of the screen should be 0.5~1.0 Ft-L by using Screen
VR.
(f) Select the R-BIAS, G-BIAS and B-BIAS on the control menu and adjust the +/– key to get the color
coordinates in x=0.281 ± 0.015, y=0.311± 0.015.
(g) Receive a full white pattern. Adjust the brightness value to the center.
(h) Select the R-GAIN and B-GAIN and adjust the +/– key to get the color coordinates in x=0.281 ±
0.015, y=0.311 ± 0.015.
(i) Adjust the ABL control to get the screen luminance to 30 Ft/L (a full white pattern over 30 Ft/L)
(j) Check if the x, y coordinates of color analyzer is in x=0.281±0.015, y=0.311±0.015.
If the color coordinates is out of range, adjust the R. G. B BIAS & GAIN to get the coorinates in
x=0.281, y=0.311. Make sure that the coordinates is in range.
(k) Select 6500°K on the OSD Menu and set the color coordinates in x=0.313, y=0.329 at the
maximum contrast control and center brightness control
(l) Check if a full white pattern is over 30Ft/L.
13