Information On The Software License For This Product - Sharp LC-40LE732E Service Manual

Operation Manual (Continued)
Appendix
Troubleshooting
Problem
• No power.
• The TV cannot be operated.
• Remote control unit does not operate.
• Picture is cut off.
• Strange colour, light colour, or dark
colour, or colour misalignment.
• Power is suddenly turned off.
• No picture.
• No sound.
• The TV sometimes makes a cracking
sound.
Troubleshooting - 3D Images
Problem
• 3D images are not displayed.
• The 3D glasses turn off
automatically.
• Switching the 3D glasses button to
2D or 3D does not cause the LED
light to green.

Information on the software license for this product

Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by
SHARP or by third parties.
Software developed by SHARP and/or third part
The copyrights for the software components and various relevant documents included with this product that were developed or
written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws.
This product also makes use of freely distributed software and software components whose copyrights are held by third parties.
TVa
• Check if you pressed
If the indicator on the TV lights up red, press
• Is the AC cord disconnected?
• Check if you pressed a on the TV.
• External influences such as lightning, static electricity, etc., may cause improper operation. In this
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging
it in after one or two minutes.
• Are batteries inserted with polarity (e, f) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminating to the remote control sensor?
• Is the image position correct?
• Are screen mode adjustments (Picture format) such as picture size made correctly? (Page 26.)
• Adjust the picture tone.
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the "Picture" setting (Page 19).
• The TV's internal temperature has increased.
Remove any objects blocking the vent or clean.
• Is the "Sleep Timer" set? Select "Off" from the "Time" menu (Page 21).
• Is "No Signal Off" or "No operation Off" activated?
• Are connections to external equipment correct? (Pages 13, 14 and 15)
• Is the input signal type selected correctly after connection? (Page 10)
• Is the correct input source selected? (Page 10)
• Is the picture adjustment correct? (Pages 19)
• Is the antenna connected properly? (Page 8)
• Is the volume too low?
• Make sure that headphones are not connected.
• Check if you pressed e on the remote control unit.
• This is not a malfunction. This happens when the cabinet slightly expands and contracts
according to changes in temperature. This does not affect the TV's performance.
• Is "3D auto change" set to "No"? Press 3D to switch to 3D mode.
• If "3D auto change" is set to "Yes" but no 3D images are displayed, check the display format of the
content being viewed. Some 3D image signals may not be recognized as 3D images automatically.
Press 3D to select the appropriate display format for the 3D image.
• Are the 3D glasses set to 3D mode?
• Is there an obstacle between the 3D glasses and the TV, or is something covering the infrared
receiver on the 3D glasses? The 3D glasses operate by receiving a signal from the TV. Do not place
anything between the 3D infrared emitter on the TV and the infrared receiver on the 3D glasses.
• Is there an obstacle between the 3D glasses and the TV, or is something covering the infrared
receiver on the 3D glasses? The 3D glasses turn off automatically after three minutes if no signal
is received from the TV. Do not place anything between the 3D infrared emitter on the TV and the
infrared receiver on the 3D glasses.
• Is the battery in the 3D glasses exhausted? If the LED light does not light after pressing the power
button for more than one second, the battery is exhausted. Recharge the battery via mini USB
connector.
11
Possible Solution
on the remote control unit.
TVa
.
Possible solution
LC-40LE732
LC-46LE732