Pingtek PT48250-B Original Instructions Manual

Pingtek PT48250-B Original Instructions Manual

250mm(10”) table saw

Advertisement

250mm(10") Table Saw
Original Instructions
PT48250-B
©The contents of this Instruction Manual may not be copied, reproduced, republished, downloaded, posted, broadcast or
transmitted in any way without first obtaining the written permission of Pingtek Power Tools UK Ltd the copyright owners.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT48250-B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pingtek PT48250-B

  • Page 1 250mm(10”) Table Saw Original Instructions PT48250-B ©The contents of this Instruction Manual may not be copied, reproduced, republished, downloaded, posted, broadcast or transmitted in any way without first obtaining the written permission of Pingtek Power Tools UK Ltd the copyright owners.
  • Page 2: For Your Safety

    It must not be modified in any way, or used IMPORTANT INFORMATION Do not place the tool on damp surfaces. to power any other equipment or drive any For any questions relating to this guarantee Thank you for your purchase of a Pingtek other accessories other than those Use a clean, dry workbench if available.
  • Page 3: Labels And Symbols

    (These General Power Tool Safety Unmodified plugs and matching outlets will remove it yourself. Once the dust has been damaged. Contact Pingtek Power Tools for Instructions are as specified in reduce the risk of electric shock. deposited on surfaces, hand to mouth replacement labels.
  • Page 4 Check clothing and gloves away from moving be avoided. Pingtek is not liable for damage equipment when necessary. This could parts. Loose clothes, jewellery or long hair misalignment or binding of moving parts, that occurs during transit. This will be the...
  • Page 5 Always use either the fence or mitre gauge ● Use recommended accessories. Only from the work area. use genuine Pingtek accessories. has been switched OFF, and the blade has to position and guide the work. ● Do not use High Speed Steel (HSS) come to a complete halt.
  • Page 6: Technical Specification

    ●The declared vibration total value has IN THE BOX Annotated Overall View of Pingtek Table Saw been measured in accordance with a ITEM standard test method and may be used for Instruction & Assembly Manual comparing one tool with another.
  • Page 7: Attaching The Table Extensions

    Study carefully the exploded view of the tightness at this stage. Table Saw Body. help competent person when Machine Stand below. ●With competent help, lift the Main Table attempting this procedure. You will now have the Front of the Machine Saw Body with its attached Machine Stand ●Remove Table...
  • Page 8: Rear Table Extension

    ●Attach the other ends of the support struts STEP 4 STEP 6 ●The Blade Guard should automatically to the outer edge of the Table Extension ATTACHING THE BLADE GUARD THE SLIDING MITRE GAUGE (Fig. 4) adjust to accommodate any thickness of again using Ø6mm x 12mm bolts and nuts material.
  • Page 9: The Rip Fence

    A dual Tilt Locking Mechanism Knob on the main protractor body. ‘On’ and ‘Off’ buttons. your Pingtek Machine locks the blade at the YOUR MACHINES CONTROLS ●Push the ‘ON’ button to start the machine required tilt angle.
  • Page 10 RIP CUTTING (Fig. 11) the blade. ●Set the mitre gauge to 0° and adjust the To Cross Cut: Fig. 11 Note: When Rip Cutting or Bevel Rip faceplate so that it does not touch or foul ●Set the Mitre Gauge to 0° and tighten Cutting long boards or large panels we the saw blade as it passes.
  • Page 11: Maintenance Warning

    Rip Fence the blade and any other part of the ●Ensure that both blade flanges are clean by Pingtek in this machine. Faceplate and prevent possible ‘kickback’. machine. and free from any contamination (sawdust,...
  • Page 12 0° index mark. When the Mitre Gauge is set at 0° the Pingtek recommend that for any procedure are facing to the front of the saw, and that ●Tighten the cross headed screw.
  • Page 13: Declaration Of Compliance

    DECLARATION OF COMPLIANCE IMPORTANT CUSTOMER CONTACT DETAILS We: PINGTEK INDUSTRIAL CO. LTD This product has been carefully manufactured subjected As the supplier of the item listed below declare that the product: Pingtek’s stringent Quality Control (QC) Process. 250mm Table Saw PT –...

Table of Contents

Save PDF