Appendix V. Control Ascii Protocol; Appendix Vi. Communication Settings; 附录五、控制Ascii协议; 附录六、通讯设置 - Crown CXM2000 Operation Manual

CXM2000 Monitor and Crossover System
7 Appendix
(continued)
7.附录
（接上一页）

Appendix V. Control ASCII Protocol

附录五、控制ASCII协议
Connecting the CXM2000 to PC via RS-232 connector allows the fault detection details to be viewed. The command protocol between the CXM2000 and basic cinema system is the ASCII protocol, which is used to implement the fault detection management.
通过RS-232接口可以连接CXM2000至PC，以查看故障检测所得信息。该连接使用下表所示的ASCII协议，可以实现故障检测管理的功能。
Input Command 输入命令 Feedback from CXM2000 返回信息
CXM2000 System Status Inquire All system Amplifiers and speakers are GOOD.
L Low Frequency Amplifier status is Fault.
L Low Frequency Speaker status is Fault.
L High Frequency Amplifier status is Fault.
L High Frequency Speaker status is Fault.
R Low Frequency Amplifier status is Fault.
R Low Frequency Speaker status is Fault.
R High Frequency Amplifier status is Fault.
R High Frequency Speaker status is Fault.
C Low Frequency Amplifier status is Fault.
C Low Frequency Speaker status is Fault.
C High Frequency Amplifier status is Fault.
C High Frequency Speaker status is Fault.
L Amplifier status is Fault.
L Speakers status is Fault.
R Amplifier status is Fault.
R Speakers status is Fault.
C Amplifier status is Fault.
C Speakers status is Fault.
SW1 Amplifier status is Fault.
SW1 Speakers status is Fault.
SW2 Amplifier status is Fault.
SW2 Speakers status is Fault.
LS Amplifier status is Fault.
LS Speakers status is Fault.
RS Amplifier status is Fault.
RS Speakers status is Fault.
BSL Amplifier status is Fault.
BSL Speakers status is Fault.
BSR Amplifier status is Fault.
BSR Speakers status is Fault.
CXM2000 System Configuration L, R, C screen Speaker is JBL "XXXXXXXX"
Speaker is "XXXXXXXX"
Fault detection is "XXXXXXXX"
System is "X.1" Speaker
SW1 is "XXXXXXXX"
SW2 is "XXXXXXXX"
Application Version is "XXXXXXXX"
HW Version is "X"
Operation Manual
page 20
CXM2000 影院扬声器优化/监听系统
Note 详情
All channels are good
Bi-Amp mode * The data is all in ASCII format. If the input command cannot be recognized, it will prompt the information below:
Bi-Amp mode
* 所有数据都为ASCII格式。如果输入的命令不能被识别，将会提示以下信息：
Bi-Amp mode
Bi-Amp mode
Invalid Command
Bi-Amp mode
Bi-Amp mode
1) CXM2000 System Configuration
Bi-Amp mode
2) CXM2000 System Status Inquire
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode

Appendix VI. Communication Settings

Passive mode
Passive mode
附录六、通讯设置
Passive mode
Passive mode
Item
Passive mode
Passive mode
Operating Mode
SW1 is available
Hardware Handshaking
SW1 is available
SW2 is available
Flow control
SW2 is available
Synchronous system
Transmission
Data Length
Parity
Stop Bit
Speaker Name
"Bi-Amp" or "Passive"
"Enable" or "Disable"
"5.1" or "7.1"
"Enable" or "Disable"
"Enable" or "Disable"
A, B, C, D...
操作手册
Specification
Full Duplex
None
None
Asynchronous
9600
8 bits
None
1