Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Configuration Manual
Advertisement
Table of Contents
Related Manuals for Amer.com SS2GR50i
Summary of Contents for Amer.com SS2GR50i
- Page 1 SS2GR50i / SS2GR26ip / SS2GR26i L2/L4 Managed Gigabit Ethernet Switch With IP Stacking and PoE Support Installation Guide Version 1.1...
-
Page 2: Contact Information
Copyright © Amer.com Corp., 1997-2007 All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Amer.com, as stipulated by the United States Copyright Act of 1976. - Page 3 FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
-
Page 4: Table Of Contents
Contents Chapter 1 Introduction ..............1-1 1.1 Product Brief ...................1-1 1.1.1 Overview....................1-1 1.1.2 Features and Benefits ................1-1 1.2 Physical Specification..............1-2 1.3 Hardware Components..............1-3 1.3.1 Front Panel .................... 1-3 1.3.2 Back Panel..................... 1-3 1.3.3 LED Explanation ................... 1-4 1.3.3.1 Port LEDs .................. -
Page 5: Chapter 1 Introduction
IP stacking (up to 24 units, also work with layer 3 10G switches from Amer.com) and industrial standard CLI shell and Web GUI. -
Page 6: Physical Specification
SS2GR50i/26i series also support IEEE802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users. SS2GR50i/26i series switch fully support DiffServ Module. The switch can provide 8 priority queues port. -
Page 7: Hardware Components
SFP), 1 Console port and 32 LED’s on the front panel Fig 1-1 front panel SS2GR26I/SS2GR26IP SS2GR50I has 46x 10/100/1000Base-T ports, 4x1000Mb Combo ports (4 RJ-45 and SFP), 1 Console port and 56 LEDs. The front panel of SS2GR50I is shown below: Fig 1-2... -
Page 8: Led Explanation
Installation Guide There is one 110~230V AC power supply plug on the back panel of the SS2GR50i/ SS2GR26i series. Fig 1-3 SS2GR50i / SS2GR26i back panel 1.3.3 LED Explanation The front panel LED of SS2GR50i/SS2GR26i series switch has two types of port LED and status LED, the explanation is shown as below: 1.3.3.1 Port LEDs... - Page 9 Installation Guide Panel Symbol Status Description On (yellow) Port is linked as 10Mbps or 100Mbps Port is linked as 10Mbps or 100Mbps and Blink (yellow) receives/sends data Port1-24(Link/Act) On (Green) Port is linked as 1000Mbps Port is linked as 1000Mbps and receives/sends Blink (Green) data Port linked failure...
-
Page 10: Status Leds
Installation Guide Fig 1-5 SS2GR50i LED Table1.2 SS2GR50I port LED description Panel Symbol Status Description On (yellow) Port is linked as 10Mbps or 100Mbps Port linked 10Mbps 100Mbps Blink (yellow) receives/sends data Port1-48(Link/Act) On (Green) Port is linked as 1000Mbps... -
Page 11: Front Panel Port Description
On (Yellow) System is initializing diagnosis Blink(Yellow, Green) Boot is initializing 1.3.4 Front Panel Port Description The front ports of SS2GR50I/26I series, are shown below and described in the following table. Table 1-4 Switch interface description Interface mode Spec RJ-45... - Page 12 Installation Guide 9/125um single mode fiber: 40km MGBS-GLX70, SFP-LH-70-L transceiver: 9/125um single mode fiber: 70km MGBS-GLX120, SFP-LH-120-L transceiver: 9/125um single mode fiber: 120km...
-
Page 13: Chapter 2 Hardware Installation
2.1.1.1 Dust and Particles Dust is harmful to the safe operation of SS2GR50i/26i series. Dust can lead to electrostatic adherence, especially likely under low relative humidity, causing poor contact of metal connectors or contacts. Electrostatic adherence will result in not only reduced product lifespan, but also increased chance of communication failures. -
Page 14: Temperature And Humidity
Installation Guide the threshold value. Average (mg/m³) Max (mg/m³) 0.006 0.03 0.04 0.15 0.05 0.15 0.01 Table 2.2 Environmental Requirements: Particles 2.1.1.2 Temperature and Humidity Although the switch is designed to use 4 fans, the site should still maintain a desirable temperature and humidity. -
Page 15: Power Supply
Installation Guide air-conditioning system failure, and normal operation conditions should be recovered within 5 hours. 2.1.1.3 Power Supply The power input parameters for the switch is shown as below: AC input: 100~240VAC Frequency: 50~60H Before powering on the power supply, please check the power input to ensure proper grounding of the power supply system. -
Page 16: Rack Configuration
Installation Guide Provide electromagnetic shielding if necessary. 2.1.1.6 Rack Configuration The dimensions of the switch are designed to be mounted on a standard 19’’ rack, the dimensions are 440mm x 44mm x 410mm (W x H x D). Please ensure good ventilation for the rack. -
Page 17: Installation Preparation
2.3 Installation Guide 2.3.1 Installing the Switch Please mount SS2GR50i/26i series on the 19’’ rack as below. Attach the 2 brackets on the SS2GR50i/26i series with screws provided in the accessory kit. Fig 2-1 Rack-mounting the switch Put the bracket-mounted switch smoothly into a standard 19’’ rack. Fasten the switch... -
Page 18: Console Connecting Console
Do not place anything on top of the switch. Do not block the blowholes on the switch to ensure the proper operation of the switch. 2.3.2 Console Connecting Console SS2GR50i/26i series provides a RJ-45 interface console port. Fig 2-3 Connecting Console cable The connection procedure is listed below Find the console cable provided in the accessory kit. -
Page 19: Sfp Transceiver Installation
Power on the switch and the character terminal. Configure the switch through the character terminal. 2.3.3 SFP Transceiver Installation SS2GR50i/26i series provides multiple 1000Mb SFP transceiver slots. The procedure for installing the SFP transceiver is shown below: Step 1: Put on a ESD wrist strap (or antistatic gloves) Step 2: Insert the SFP transceiver to the guide rail inside the fiber interface line card. -
Page 20: Power Supply Connection
Do not stare at the fiber bore when the switch is in operation. That may hurt your eyes. 2.3.5 Power Supply Connection SS2GR50i/26i series uses110/220V AC power supply by default, and can fit a totally range for the voltage’s small change. Please read the power input specification for the detailed information. - Page 21 Installation Guide ©Amer.com Corp. 1997-2007 All rights reserved.
Need help?
Do you have a question about the SS2GR50i and is the answer not in the manual?
Questions and answers