Panasonic DMP-B15 Operating Instructions Manual page 43

Operation
The unit is on but cannot be
operated.
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
No response when remote
control buttons pressed.
Start up is slow.
It takes time before play starts.
Played back image is distorted
or does not playback correctly.
([AVCHD])
Cannot set "On" in "24p Output". ≥Only when this unit is connected to a TV supporting 1080/24p output via an HDMI cable, you
LCD
No picture on the LCD.
The LCD is dark.
LCD pixels turn black or
radiate different colours.
Picture is distorted.
There is a lot of after-image
when playing video.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
Still pictures (JPEG) do not
play back normally.
Sound
No sound from the unit's
speaker.
Cannot hear the desired audio
type.
Cannot switch audio.
≥The unit can be operated only when closed with the screen facing outwards (
in "Installation of the unit").
≥Is the incorrect playback media or operation function selected?
≥The unit may not be operating properly due to lightning, static electricity or some other
external factor. Turn the unit off and then back to ON. Alternatively, turn the unit off,
disconnect the power source (AC or battery pack), and then reconnect it.
≥Condensation has formed. Wait 1 to 2 hours for it to evaporate.
≥Insert the media correctly with the label facing up. (
≥The media is dirty. ( 5)
≥You tried to play a blank media or unplayable media on this unit. (
≥[DivX]: If playing DivX VOD content, refer to the homepage where you purchased it. (
≥The unit can be operated only when closed with the screen facing outwards (
in "Installation of the unit").
≥Check that the battery is installed correctly. (
≥The battery is depleted: Replace it with new one. (
≥Point the remote control at the remote control sensor and operate. (
≥Make sure that "Quick Start" is set to "On". (
≥Start up takes time in the following situations.
j Immediately after a power failure or the AC adaptor is connected.
j When the unit is connected with an HDMI cable.
≥High definition video (transfer rate of 18 Mbps or faster) cannot be played back correctly if it
was recorded on a DVD compatible to double speed or slower.
can set to "On". ( 34)
≥Check connections. ( 11)
≥Select "On" in "Monitor". (
≥The LCD screen is turned off automatically when the LCD screen is rotated. (
≥The LCD screen can be turned on only when the unit is closed with the screen facing
outwards. ( 10, 3 or 4 in "Installation of the unit")
≥[DivX]: Images may not be output due to how files were created. (
≥Select the appropriate picture quality mode. (
≥The LCD is constructed with precision technology so 99.99 % of the pixels are active, but of
the remaining of 0.01 %, there are pixels that may be black or emit light constantly. This
phenomenon is not a malfunction.
≥The quality of video will lower on the screen of this unit when HDMI is connected. (
≥Turn "3D NR" or "Integrated NR" off if it is on. (
≥Check the setting for "TV Aspect". (
≥Check the setting for "Screen Aspect". (
≥The images that were edited on the PC, such as Progressive JPEG, etc., may not play back.
( 38)
≥The speaker is off if headphones are connected.
≥Turn up the volume. ( 14)
≥Press [AUDIO] to select the audio. (
≥[DivX]: Audio may not be output depending on how files were created. (
≥There are discs for which audio cannot be changed because of how the disc was created.
≥When connecting an amplifier/receiver using an HDMI cable, you cannot switch the audio if
"Dolby D/Dolby D +/Dolby TrueHD" or "DTS/DTS-HD" is set to "Bitstream". Set "Dolby D/Dolby
D +/Dolby TrueHD" or "DTS/DTS-HD" to "PCM" or connect using AV IN/OUT terminal. (
13)
9)
9)
36)
13)
13)
24)
34)
16)
16)
10, 3 or 4
6)
20)
10, 3 or 4
9)
10)
38)
25)
38)
33)
43
RQT9338