Advertisement
Quick Links
Please review this entire manual before beginning assembly.
By doing so it will help you better understand each step as you progress in the
actual building of your kit, and you will do a better job in assembly.
INCLUDED IN THIS KIT:
• All laser cut Depron parts
• Balsa ailerons, balsa horizontal stabilizer, and balsa elevator
• Plywood motor mount
• 3 Pushrods + 1 Pushrod tube
• 3 Micro control horns
• 1 Carbon fiber tube and 2 flat spars
• 1 Balsa short stick for servo mount
SPECIFICATION:
• Wing Span: 24 inch
• Length: 17.5 inch
• Dry weight: 5.5 oz
• Ready to Fly Weight: 7.7 oz with 2S 7.4v 1050mAh
NEEDED BUILDING TOOLS:
• Foam Safe / Odorless CA glue + Foam Safe Accelerator
(User Friendly Odorless "UFO" highly recommended)
• Blenderm Hinge Tape or Transparent Scotch Tape
• Sandpaper + Sanding Bar
• Hobby Knife
• Ruler (preferably metal)
REQUIRED EQUIPMENT:
• 4 Channel Transmitter + Micro Receiver (AR6100E, AR6110E or similar)
• 2 Micro Servos (5~8 gram)
(HXT500, SG-50 or Hitec HS-55 or similar)
• Small & Light High KV Outrunner
(HXT 24gram 3000kv, Turnigy 2730 3000kv or similar)
• ESC: 30Amp
• APC Prop: (4.75x4.75 on 3S ONLY), or (5x5~6x5 on 2S only)
• Prop Adapter: 3mm (will fit both recommended motors)
• Lipo Battery: Nano-Power 1100mAh 11.1v 35C
• Maximum Battery size: 73x34x18 mm
(Size is very crucial here. This size is the largest fit for width and thickness possible in
the small fuselage)
Advertisement
Related Manuals for nanoplanes Baby Shark
Summary of Contents for nanoplanes Baby Shark
- Page 1 Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in assembly. INCLUDED IN THIS KIT: •...
- Page 2 The uncut Depron parts Look carefully at this as you will receive 4 rows of parts. These them. parts will be doubled (Notice the direction of the taper on the center sections on the first 2 rows.) Begin by carefully cut- Double up the parts ting all the tabs.
-
Page 3: Very Important
Glue the fuselage Sand a bevel on the doublers over the side stabilizer about 20 pieces. Use left over degrees. scraps to ensure the parts line up properly (It is better to sand a by inserting them in the bevel on both sides slots. - Page 4 This is how it should Here is what your look like after sanding stabilizer with elevator both the top and bottom attached should look to a taper towards the like. (Note the bevel trailing edge. on both sides... This is important that you do it this way for best perfor- mance.)
- Page 5 Remove the part and Make sure there is look carefully as you room for the battery will see the imprint of hatch to open and the motor mount. close. Again, ONLY glue the front part on. Cut out just the one The remaining parts of layer (3mm deep) of the fuselage as shown...
- Page 6 Apply glue to sections Glue the longer 20” in Red. Marking yours carbon flat spar to the the same way only on back of the center wing the outer most edges panel. Make sure it is will help you in later centered equally on steps with sanding the the left and right of the...
- Page 7 The trailing edge of Make sure you use a the wing tips will need sanding bar to ensure sanding. your sanding is uni- form and level where needed. This helps greatly with sanding the tapered trailing edges. Here you can see an- Sand them down to other angle of the taper closely match the...
- Page 8 See here how both Measure 1/4 inch from sides are bevelled the inside Tape the aileron and And measure 1/4 inch trim as shown down. Make a dot and drill and hole for the control horn. Trim both sides and Here is another easy attach to the wing.
- Page 9 A close up of the lead- Trim the area around ing edge. Notice that the servo. the front bottom edge is lifted up from the floor. This is all there is to create the Semi- symmetrical airfoil. Your wing and fuselage will not fit perfectly and You will also need to will seem to be incor-...
- Page 10 Cut a V groove to nicely Install the Pushrod on seat the pushrod tube. the control horn first. Trim the elevator Now insert it on the control horn as shown inner most hole of the and glue it in the eleva- servo arm then screw tor.
- Page 11 Insert the rudder into Insert it and glue it in. the slots both below and above the elevator. It should fit easily. You will notice 3 On the top portion, only different pieces as apply glue to the ends shown. They are and pinch as shown.
- Page 12 And remove it if and The motor may be too when needed by cutting close to the nose of the the tape. fuselage. Now insert your aileron Trim it to clear the pushrod on your servo motor if needed arm and line up your control horn.
- Page 13 A view of the tight The tape over the rear installation shown hatch as shown. Again lightly sand the edges rounded while holding it down before taping the edges if you want streamlined rounded edges The battery connector For you to better showing through the understand where to hole.
- Page 14 Airplane flight Characteristics: This micro speed plane is Insanely FAST on the 3S setup PLEASE follow the recommended control set ups including EXPO, otherwise it will be challenging to fly as it is a very responsive high performance design that can be easy and fun to fly if set up properly.