1 Safety Precautions 1.1. General Guidelines 1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials. 2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the wires have been broken or disconnected, do not attempt to repair or re-wire the units.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor [chip] components.
2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
3 Service Navigation 3.1. PCB Layout Board Name Function Power Supply Main AV input, processing Remote receiver, Power LED, C.A.T.S sensor Data Driver (Lower Right) Data Driver (Lower Center) Data Driver (Lower Left) Scan Drive Sustain Drive Sustain out (Lower) Scan out (Upper) Non serviceable.
3D Eyewear Battery Coin-shaped lithium battery CR2025 Operation time: Approx. 75 hours in continuous use of the battery made by Panasonic • Use Panasonic 3D Eyewear supporting Bluetooth wireless technology. Note Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
5 Technical Descriptions 5.1. Specification of KEY for DTCP-IP, WMDRM and Widevine 5.1.1. General information: 1. NAND Flash (IC8900) for spare parts has the seed of KEY for each DTCP-IP for DLNA, WMDRM for Netflix and Widevine for CinemaNow. 2. The final KEY data will be generated by Main IC (IC8000) when SELF CHECK was done and are stored in both Main IC (IC8000) and NAND Flash (IC8900).
6 Service Mode 6.1. How to enter into Service Mode 6.1.1. Purpose After exchange parts, check and adjust the contents of adjustment mode. While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds Note: Service Mode can not be entered when 3D signal input.
Contents of adjustment mode 6.1.4. • Value is shown as a hexadecimal number. • Preset value differs depending on models. • After entering the adjustment mode, take note of the value in each item before starting adjustment. Main item Sub item Sample Data Remark ADJUST...
6.2. Option - Mirror Picture can be reversed left and right or up and down. 00 : Default (Normal picture is displayed) 01 : Picture is reversed left and right. 02 : Picture is reversed up and down. Hint : If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in A-board.
6.4. Hotel mode 1. Purpose Restrict a function for hotels. Item Function 2. Access command to the Hotel mode setup menu Mode Select hotel mode On/Off In order to display the Hotel mode setup menu: Input Select input signal modes. While pressing [VOLUME (-)] button of the main unit, Set the input, when each time power is switched on.
6.5. Data Copy by USB Memory Note: SD card can not be used for Data Copy. 6.5.1. Purpose (a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to USB Memory and then copy to new A-board. (b) Hotel (Copy the data when installing a number of units in hotel or any facility): When installing a number of units in hotel or any facility, the data in master TV can be copied to USB Memory and then copy to other TVs.
Page 14
6.5.3. Data copy from TV set to USB Memory 1. Turn on the TV set. 2. Insert USB Memory with a startup file (pwd file) to USB terminal. On-screen Display will be appeared according to the startup file automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2770 (b) For Hotel : 4850 Data will be copied from TV set to USB Memory.
Page 15
6.5.4. Data copy from USB Memory to TV set 1. Turn on the TV set. 2. Insert USB Memory with Data to USB terminal. On-screen Display will be appeared according to the Data folder automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2771 (b) For Hotel : 4851 Data will be copied from USB Memory to TV set.
7 Troubleshooting Guide For detailed troubleshooting information and circuit explanations, refer to the "QSM/Service Hints/Troubleshooting Information(TI)" and Seminar/Training Manual/Technical Guide(TG) documents posted on the TSN web site. For information about this model, type TC-P2013 in the model box under "Direct Search".
8 Service Fixture & Tools 8.1. SC jig Purpose: To find the failure board (SC or SU/SD) when the power LED is blinking 7 times. SC jig: Jumper connector to connect to SC50 connector on SC board Part number: TZSC09187 How to use: Caution: Remove SC jig from SC board after inspection.
9 Disassembly and Assembly Instructions 9.1. Disassembly Flow Chart for the Unit This is a disassembly chart. When assembling, perform this chart conversely.
9.2. Disassembly Procedure for the Unit 9.2.1. Remove the Pedestal stand 9.2.4. Remove the Wi-Fi module 1. Remove the Plasma panel section from the servicing 1. Remove the screw (×1 ) and remove the Wi-Fi stand and lay on a flat surface such as a table (covered module.
Page 20
9.2.7. Remove the P-Board 8. Remove the screws (×2 9. Remove the Heatsink (bottom) and the Thermal pad. Caution: To remove P.C.B. wait 1 minute after power was off for discharge from electrolysis capacitors. 1. Unlock the hooks and the tapes to free the cables 2.
Page 21
9.2.11. Remove the Woofer 9.2.13. Remove the SD-Board 1. Unlock the hooks and the tapes to free the cables. 1. Disconnect the flexible cables (SD1, SD2, SD3, SD4 and 2. Disconnect the Relay connector. SD5) connected to the SD-Board. 2. Disconnect the flexible cable (SU11-SD11) and the bridge 3.
Page 22
9.2.15. Work instructions for the Rubber 9.2.17. Work instructions for the Rubber sheet for SC-Board sheet for SS-Board 1. Rubber sheets are put between the board and rear cover 1. Rubber sheets are put between the board and rear cover for EMC requirement and heat radiation.
Page 23
9.2.19. Remove the USB cable (A-WiFi) 9.2.22. Remove the Cabinet assy from the Plasma panel section 1. Remove the screw (×1 2. Remove the USB cable (A-WiFi). 1. Place the Cabinet assy on a flat surface of a table (covered by a soft cloth) and a cushion. 9.2.20.
Page 24
9.2.23. Remove the Contact metals 9.2.26. Remove the C3-Board 1. Disconnect the flexible cables (CB12, CB13, CB14 and 1. Remove the screws (×16 CB15). 2. Remove the Contact metal side (L, R). 2. Disconnect the flexible cables (C31 and C36). 3.
10 Measurements and Adjustments 10.1. Adjustment 10.1.1. Vsus selection Caution: When Plasma panel or A-board is replaced, Vsus should be set to LOW or HIGH. Procedure 1. Go into main item [VSUS] in Service Mode. LOW or HIGH will be displayed. 2.
10.1.2. White balance adjustment Name of measuring instrument Remarks Color analyzer (Minolta CS-1000 or equivalent) Procedure Remarks 1. Enter the Service mode. 2. Receive the Analog-RF (except for no signal) or set CVBS/YUV/HDMI (no signal is available). 3. Select [WB-ADJ] by using [1] and [2] key in the remote controller. 4.
11.3. Block (2/4) Diagram MAIN AV INPUT,PROCESSING USB_DP/DN IC9300 PD6H VIDEO DATA PLASMA AI VIDEO DATA LVDS DATA H/V Sync Control VIDEO DATA Sub Filed Processor P3.3V IC9803 P1.2V P3.3V DCDCIN P1.2V KEYSCAN IIC0 KEYSCAN +1.2V 1.2V KEY3 KEY3 IC9005 P2.5V 3.3V_DET1 DCDCEN2...
12 Wiring Connection Diagram 12.1. Caution statement. Caution: Please confirm that all flexible cables are assembled correctly. Also make sure that they are locked in the connectors. Verify by giving the flexible cables a very slight pull. 12.2. Wiring (1) 12.3.
Page 38
Model No. : TC-P50ST60 Accessories 3 / 3...
Page 39
Print Parts List Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks TXN/A1UJUUS CIRCUIT BOARD A 1 (RTL)PAVCA TXNC31UJUUS CIRCUIT BOARD C3 1 (RTL)PAVCA TZRNP06UJUU CIRCUIT BOARD C1 1 (RTL)PAVCA TZRNP07UJUU CIRCUIT BOARD C2...
Page 40
C 0.1UF 16V C2010 F1G1A105A047 C 1UF 10V C2013 F1G1E103A059 C 0.01UF 25V C2014 F1G1E103A059 C 0.01UF 25V Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C2019 F1G1E103A059 C 0.01UF 25V...
Page 41
C 100PF, J, 16V C5013 F1G1A105A047 C 1UF 10V C5014 F1G1A105A047 C 1UF 10V C5015 F1G1A105A047 C 1UF 10V Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C5016 F1G1A105A047 C 1UF 10V...
Page 42
Print Parts List Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C8110 F1G1C183A146 C 0.018UF, 16V 1 PAVCA C8111 F1G1C104A077 C 0.1UF 16V C8112 F1K1V106A010 C 10UF, 25V 1 PAVCA C8114...
Page 43
C 1UF 10V C9325 F1G1A105A047 C 1UF 10V C9326 F1G1A105A047 C 1UF 10V C9335 F1J1A106A043 C 10UF, 10V Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C9336 F1J1A106A043 C 10UF, 10V...
Page 44
C 1 uF 16 V C16193 F2A1E1010130 E 100UF, 25V C16195 F1K1E105A029 C 1UF, 25V C16202 F0C2E225A286 C 2.2UF, 250V 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks C16203 F0C2E225A286 C 2.2UF, 250V...
Page 45
F1L2E224A028 C 0.22UF, 250V C17334 F1L2E224A028 C 0.22UF, 250V C17335 F1L2E224A028 C 0.22UF, 250V C17338 F1L2E224A028 C 0.22UF, 250V Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks K1MY55B00001 55P CONNECTOR K1MY55B00001...
Page 46
1 PAVCA D504 DA2J10100L DIODE D505 B0ECKM000053 DIODE D506 DZ2J100M0L ZENER DIODE D507 DZ2J051M0L ZENER DIODE Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks D509 DZ2J100M0L ZENER DIODE D510 B0AAFK000004 DIODE...
Page 47
DA2J10100L DIODE D16191 B0ECKP000055 DIODE D16192 DA2J10100L DIODE D16196 DZ2J051M0L ZENER DIODE D16243 DA3X103E0L DIODE Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks D16251 DZ2J330M0L ZENER DIODE D16252 DZ2J330M0L ZENER DIODE...
Page 48
1 PAVCA IC16786 MIP3910MSSCF IC16787 C0DBZYY00532 1 PAVCA IC16795 C0CBALC00012 IC16921 C1ZBZ0004557 1 PAVCA D0GDR00J0004 M 0 OHM, 1/8W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks D0GDR00J0004 M 0 OHM, 1/8W...
Page 49
1 PAVCA L16070 G0ZZ00002183 PEAKING COIL L16071 G0ZZ00002183 PEAKING COIL L16072 G0ZZ00002183 PEAKING COIL L16073 G0ZZ00002183 PEAKING COIL Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks L16303 G0C471MA0049 PEAKING COIL L16411 G0CR38K00001...
Page 50
B1ABPF000011 TRANSISTOR 1 PAVCA Q104 B1ABDF000026 TRANSISTOR Q105 B1ADCF000172 TRANSISTOR 1 PAVCA Q201 B1CERT000010 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks Q202 B1ABNE000003 TRANSISTOR 1 PAVCA Q300 B1CERQ000093...
Page 51
1 PAVCA R152 D0GD220JA052 M 22 OHM,J,1/8W R153 D0GD220JA052 M 22 OHM,J,1/8W R154 D0BF330JA051 M 33 OHM,J,1/2W 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R155 D0BF330JA051 M 33 OHM,J,1/2W...
Page 52
R523 D0GB223ZA038 M 22KOHM,J,1/10W 1 PAVCA R524 D0GB473JA065 M 47KOHM J. 1/10W R526 D0GB103JA065 M 10K OHM J 1/10W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R527 D0GB101JA065 M 100 OHM,J,1/10W...
Page 53
M 91KOHM, J,1/10W 1 PAVCA R734 D0GB183ZA038 M 18KOHM,J.1/10W 1 PAVCA R735 D0GB623ZA038 M 62KOHM, J,1/10W 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R736 D0GB622ZA038 M 6.2KOHM 1/10W...
Page 54
D0GA223JA023 M 22K OHM J 1/16W R5013 D0GA103JA039 M10KOHM, J.1/16 W 1 PAVCA R5040 D0GA102JA039 M1KOHM, J.1/16 W 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R5041 D0GA333JA023 M 33KOHM,J,1/16W...
Page 55
M 68 OHM, J,1/16W R8621 D0GA680JA023 M 68 OHM, J,1/16W R8622 D0GA680JA023 M 68 OHM, J,1/16W R8623 D0GA680JA023 M 68 OHM, J,1/16W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R8624 D0GA680JA023...
Page 56
Print Parts List R9168 D0GA472JA023 M 4.7KOHM, J,1/16W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R9197 D0GA103JA039 M10KOHM, J.1/16 W 1 PAVCA R9198 D1H81014A042 NETWORK RESISTER 1 PAVCA R9205 D0GA102JA039 M1KOHM, J.1/16 W...
Page 57
M 20K OHM J.1/16W R16472 D0GA222JA023 M 2.2KOHM, J,1/16W R16473 D0GD561JA052 M 560 OHM,J,1/8W R16474 D0GA102JA023 M1KOHM, J.1/16 W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R16475 D0GA472JA023 M 4.7KOHM, J,1/16W...
Page 58
R16719 D0GB220JA065 M 22 OHM J 1/10W R16721 D1H82204A041 NETWORK RESISTER 1 PAVCA R16761 D0GD100JA059 M 10 OHM,J,1/4W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R16763 D0GA473JA023 M 47KOHM, J,1/16W...
Page 59
M 47 OHM,J,1/10W R17307 D0GB101JA065 M 100 OHM,J,1/10W R17308 D0GB101JA065 M 100 OHM,J,1/10W R17309 D0GB101JA065 M 100 OHM,J,1/10W Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks R17310 D0GB101JA065 M 100 OHM,J,1/10W...
Page 60
K4AD01A00002 TERMINAL ZA16001 K4AD01D00020 TERMINAL 1 PAVCA ZA16002 K4AD01D00020 TERMINAL 1 PAVCA ZA16101 K4AD01D00019 TERMINAL 1 PAVCA Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks ZA16102 K4AD01D00019 TERMINAL 1 PAVCA ZA16106 K4AD01D00019...
Page 61
SCREW(C:12) XYN3+F6FJ SCREW(P:5 SS:5 SC:7 SUSD:3 SS2:2) XYN3+J10FJ SCREW XYN3+J10FJ SCREW XYN3+J10FJ SCREW XYN3+J10FJ SCREW XYN3+J10FJ SCREW Model No. : TC-P50ST60 Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks XYN3+J10FJ SCREW XYN3+J10FJ SCREW XYN4+E6FJ SCREW(INLET EARTH)
Need help?
Do you have a question about the TC-P50ST60 and is the answer not in the manual?
Questions and answers