Operation Of Remote Control - YMGI WMMS-09K-V2A(57)2 User Manual

Wall mount mini split systems dc inverter r410a-symphony solo

Hide thumbs Also See for WMMS-09K-V2A(57)2:

Installation instructions manual (23 pages)

Table Of Contents

Table of Contents

REMOTE CONTROL-BUTTON NAME & FUNCTIONS

"SWING" BUTTON: Hold the swing button (symbol

shown above) for more than 2 seconds and the

indoor air louver will start to swing between the

highest and lowest limits. Once the swing button is

released the louver will stay in the last position where

the button was released.

If the swing button is pushed just once the swing icon

will appear on the remote and the louver will swing

up and down continuously between the highest and

lowest points. Push the swing button once more and

the icon will disappear on the remote and the louver

will remain at the last point the button was pushed.

When the unit is powered off by the remote the louver

will close on the indoor unit.

Press this button to set up the desired swing angle

which circularly changes as below. (Insert swing

picture)

"U-TOUCH" BUTTON: Since the indoor unit is normally mounted high up on the wall or attached to the ceiling, the

temperature at where the return air sensor is installed inside the indoor unit is higher than what it is where the

area people stand and can feel (4 to 7 feet above the floor). If the unit uses the return air temperature as its

target control, people may feel colder than what they really want (target) in both cooling mode and heating mode.

The facts of air stratification and warm air rising and cold air dropping require users to set up, by experiments or

experience, the target temperature quite few degrees higher than what you really want , in order to reach a

satisfied or more precise indoor comfort. This is a common drawback of AC/HP units made by other manufacturers.

With YMGI's U-touch feature, this can be avoided and your comfort level can be improved.

When you press the U-TOUCH button on the remote control, the unit will use the temperature where the remote

is located as its target temperature control. Once you do so, you will notice a figure of a person surrounded by

stars appear on the remote.

Once the U-TOUCH stars appear, the remote will send a signal of the remote-local temperature to the indoor unit,

and this remote-local temperature will supersede the return air temperature as the unit's target temperature.

Every 10 minutes such signal will be sent from the remote to the indoor unit updating the remote-local

temperature. If at any time during this process no signal is received by the indoor unit from the remote, the unit

will switch back to the previously set temperature before the U-TOUCH feature is activated. To turn the U-

TOUCH feature off, simply press the U-TOUCH button until you see the symbol disappear from the remote

screen. By doing so, the return air temperature will take place of remote-local temperature as the unit's target

temperature. U-TOUCH is what YOU WANT. U-TOUCH feature brings to you a true comfort level wherever and

whenever you want.

"U-Touch" Feature Is NOT Activated:

Warmer

Roof

T+△

Colder

Temp sensor

Wall mount indoor unit

(May Feel Colder than

You Want in Summer

and Winter)

Floor

YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !

"SWING UP AND DOWN" BUTTON

Press this button, to set up swing angle,

which

circularly changes as below:

This is an universal use remote control. If remote

control sends the following three kinds of status

that the swing status of main unit will be:

When the guide louver start to swing up and down, if

turn off the Swing, the air guide louver will stop at

current position.

which indicates the guide louver swings up and

down between that all five positions.

"U-Touch" Feature Is Activated:

Warm air rises

Roof

Cold air drops

Signal (communication)

Remete control

(Temp sensor)

(Feel More

Comfortable)

Floor

P17 OF 36

REMOTE CONTROL-BUTTON NAME & FUNCTIONS

SYMBOL DISPLAY

When power is first applied to the unit but the power has not been turned on by the remote control, then the red

power light only is displayed. When the unit has been powered on by the remote control then the running LED is

lit and the current running mode symbol is displayed at the same time.

COOLING: Running symbol and cooling symbol are lit.

HEATING: Running lamp and heating symbol are lit.

DRY: Running lamp and dry lamp are lit

FAN: Running lamp and fan lamp are lit.

AUTO: Auto lamp, running lamp and actual running mode are lit.

ALPHA NUMERIC DISPLAY

* The setting temperature range for the unit is 61 to 86 F.

* Under AUTO mode unit will display 77 F for cooling and 68 F for heating modes.