Yamaha TX7 Owner's Manual page 23

If
no
errors are
encountered
the
"FINISHED
II!"
display
will
appearfor
a
few seconds
and
then
will revert to the
"VERIFY CASSETTE
?
"
display.
If
an
error
is
found,
however,
the display
will
read
"TAPE ERROR".
If
this
happens,
try
SAVEing
the
data again.
Depending on
the cassette recorder you
use,
you
may
have
to adjust
the cassette volume
control and/or tone
control to achieve
reliable
operation.
Cleaning
and demagnetizing
the cassette recorder heads might
also help.
Pressing the
LOAD/PROT
button
in
the
SHIFT mode
calls
the
MEMORY
PROTECT
LOBd
ON/OFF
function
we
have
already seen, and
the cassette
"LOAD FUNC
?
INT"
and
"LOAD
CASSETTE?"
functions.
Start
the load procedure by
calling the
"LOAD
FUNC
?
INT"
(or
"EXT")
display.
"LOAD
FUNC
?
INT"
This function
lets
you
select
whether
the function
memory
data
from
the cassette
tape
will
be loaded
into the
TX7
function
memories
or the
DX
function memories.
Select
either
"INT", corresponding
to
the
TX7
function
memories,
or "EXT",
cor-
responding
to
the
DX
function
memories
using the
N0/-1
and
YES/ +
1
buttons.
Then
press the
LOAD/PROT
button again
to
go on
to the next
step.
"LOAD CASSETTE
?"
You
are
now
ready
to
execute
the actual load operation.
Wind
the cassette tape
to the
beginning
of the
file
to
be loded
(This
is
easier
if
you have
recorded voice
memos
on
the cassette tape,
prior to
each
data
file.
You
can monitor
the tape
sound
while searching
for
the desired
file
via
the
TX7's
PHONES
jack).
Press the
YES/ +
1
button
and
start
the cassette recorder
in
the play
mode. The TX7
display
will
respond
with
"NOW WORKING
M"
while
it
is
searching
for
the beginning
of the
file.
When
the
file is
located the display
will read
"FOUND
TX=XX", where
"XX"
is
the
file
number
of
the
file
being
loaded.
When
the
file
has
been
loaded the
TX7
display
will
read
"FINISHED!!!"
for a
few seconds and
then
will revert to
the
"LOAD
CASSETTE?"
display.
Using the
TX7
Cassette
Interface
to
Save
and Load
DX7
Voices
The TX7
cassette interface
can
also
be used
to
save
or load
all
32
DX7
voices plus
the
32
DX
function
memories
in
the
TX7.
To SAVE,
the
DX7
voice
memory
data
is
transmitted
to the
TX7
voice
memory
via
the
MIDI
interface,
and
then the
SAVE
operation
is
carried
out as described above. To
LOAD,
the cassette data
is first
loaded
into
the
TX7
memory, and
then
transmitted to the
DX7
via
the
MIDI
interface.
In
either
case the previous
memory
contents
of the
TX7
will
be completely
erased,
so
make
sure
you have
the
TX7 memory
data
on
cassette so
it
is
not completely
lost.
To
transfer the
DX7
voices
to
the
TX7
for
saving,
first
turn
the
TX7 memory
protect
function
OFF. Then
set the
DX7
to
"SYS INFO
AVAIL",
call
the
DX7
"MIDI
TRANSMIT?"
function
and
press the
DX7 YES
button
to
begin the transmission.
The TX7
display
will
read
"MIDI RECEIVED!" when
the data from
the
DX7
has
been
transferred to the
TX7
voice
memory.
Then, simply
SAVE
the
TX7
voice
memory
plus
DX
function
memory
("EXT")
as described above.
To
load
a
voice
set
from
cassette
tape
into the
DX7,
first
load the cassette
file
into
the
TX7
as
described above. Then,
to transmit the
TX7
voice
memory
contents
to
the
DX7,
turn the
DX7
internal
memory
protect function
OFF,
set
the
DX7
to
"SYS
INFO
AVAIL",
call
the
TX7
"MIDI
TRANSMIT?"
display by pressing the
TX7
MIDI
DUMP/INIT
button
In
the
SHIFT mode,
then
press the
TX7 YES/ +
1
button
to
begin
the transmission.
The
DX7 LCD
display
will
read
"MIDI
RECEIVED" when
the voices
have been
transferred to the
DX7
voice
memory.
*Make
sure
you
turn the
DX7
internal
memory
protect function
ON, and
set
"SYS
INFO UNAVAIL"
after
receiving voices from
the
TX7.
22