Table of Contents

Advertisement

QQ
3 7 63 1515 0

SERVICE MANUAL

Ver. 1.2 2007.10
HCD-DX315 is the amplifier, DVD/CD and tuner
section in DAV-DX315.
This system incorporates with Dolby*
adaptive matrix surround decoder and the DTS*
System.
*1 Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D symbol are trademarks of
Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
"DTS" and "DTS Digital Surround" are trademarks of Digital
TE
L 13942296513
Theater Systems, Inc.
AUDIO POWER SPECIFICATIONS
for the US model
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION
(FTC Output Power):
Amplifier section
US models:
Surround mode (reference) RMS output power, 10 %
Other models:
Stereo mode (rated)
www
.
Sony Corporation
9-887-186-03
Audio Business Group
2007J16-1
Published by Sony Techno Create Corporation
© 2007.10
http://www.xiaoyu163.com
1
Digital and Dolby Pro Logic (II)
2
Digital Surround
Surround mode (reference) RMS output power, 10 %
FL/FR/LS/RS/C: 84 W/ch
3 ohm at 170 - 20,000 Hz,
0.7 % THD
SW: 160 W 1.5 ohm at 40 -
170 Hz, 0.7 % THD
* Depending on the sound field settings and the source,
there may be no sound output.
THD
Inputs
Front: 143 W + 143 W
TV/VCR (AUDIO IN)
(with SS-TS53)
AUDIO IN/MIC
Center*: 143 W
Outputs (Analog)
(with SS-CT51)
Phones
Surround*: 143 W + 143
W
DVD system
(with SS-TS51)
Subwoofer*: 285 W
Laser
(with SS-WS52B)
108 W + 108 W (3 ohms at
1 kHz, 1 % THD)
x
ao
u163
y
i
http://www.xiaoyu163.com
HCD-DX315
2 9
8
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
Q Q
3
6 7
1 3
1 5
SPECIFICATIONS
THD
Front: 143 W + 143 W
(with SS-TS53)
Center*: 143 W
(with SS-CT51)
Surround*: 143 W + 143
W
(with SS-TS51)
Subwoofer*: 285 W
(with SS-WS52B)
Sensitivity: 450/250 mV
Sensitivity: 250/125 mV
Accepts low-and high-
impedance headphones.
Semiconductor laser
(DVD: λ = 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
co
.
9 4
2 8
US Model
Canadian Model
HCD-DX155
CDM81C-DVBU101
KHM-310CAB
0 5
8
2 9
9 4
2 8
Signal format system
NTSC
Tuner section
System
PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range
87.5 – 108.0 MHz
(100 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
530-1,710 kHz (with the
interval set at 10 kHz)
531-1,710 kHz (with the
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
— Continued on next page —
m
DVD RECEIVER
9 9
9 9

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-DX315

  • Page 1: Service Manual

    3 7 63 1515 0 SERVICE MANUAL US Model Canadian Model Ver. 1.2 2007.10 HCD-DX315 is the amplifier, DVD/CD and tuner section in DAV-DX315. This system incorporates with Dolby* Digital and Dolby Pro Logic (II) Model Name Using Similar Mechanism...
  • Page 2 LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 HCD-DX315 3 7 63 1515 0 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement • Never reuse a disconnected chip component.
  • Page 4: Table Of Contents

    HCD-DX315 Ver. 1.2 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTE 6-6. Printed Wiring Board – MAIN Board (Side A) – ... 37 ........... 5 6-7. Printed Wiring Board – MAIN Board (Side B) – ... 38 6-8.
  • Page 5: Servicing Note

    Although this is not a seconds again. malfunction and for Sony service use only, 2. The message “UNLOCKED” is displayed and the tray is normal system operation will not be possible. unlocked.
  • Page 6 HCD-DX315 3 7 63 1515 0 HOW TO OPEN THE DISC TABLE WHEN POWER SWITCH TURNS OFF tweezers Insert tip of tweezers through the hole gear of bottom plate, and roate the gear in the counter-clockwise direction. DVD lid tape Attach an adhesive tape on the DVD LID and draw it out.
  • Page 7 HCD-DX315 3 7 63 1515 0 Fix the capacitors with adhesive agent as follows Fixing the capacitors with adhesive agent is required by the safety regulation. Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
  • Page 8 HCD-DX315 3 7 63 1515 0 Precaution on the connector processing of the POWER board. MAIN BOARD (Parts face side) IC504 CN3002 CN506 POWER BOARD AC IN (Parts face side) CN902 CN904 When re-assembling, leave 30 mm between CN901 harnesses A and B for safety.
  • Page 9: General

    HCD-DX315 SECTION 2 This section is extracted from instruction manual. 3 7 63 1515 0 GENERAL Front panel A "/1 (on/standby) (29) G PHONES jack (29) H VOLUME control (29) B Front panel display (92) I AUDIO IN/A.CAL MIC jack (19, 31)
  • Page 10 HCD-DX315 3 7 63 1515 0 Front panel display About the indications in the front panel display A Lights up when the time information of G Playing status (DVD function only) a title or chapter appears in the front H Lights up when the DYNAMIC BASS is panel display.
  • Page 11 HCD-DX315 3 7 63 1515 0 Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS [/1 (on/standby) 1 (19, 22, 29, A – O P – Z 37, 58) AMP MENU wg (22, 31, 60, 62, PICTURE NAVI 6 (37, 60) TV [/1 (on/standby) ej (60) PRESET +/–...
  • Page 12: Disassembly

    HCD-DX315 Ver. 1.2 SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
  • Page 13: Case, Front Panel Assy

    HCD-DX315 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE, FRONT PANEL ASSY 4 two screws (CASE3 TP2) 6 five screws (+BVTP 3 × 8) 7 case 9 w ire (flat type)
  • Page 14: Fl Board, Sw Board

    HCD-DX315 3 7 63 1515 0 3-3. FL BOARD, SW BOARD When reassembling, route the harness and flexible cable as shown in the illustration. 9 wire (flat type) 23core (CN801) 7 connector (CN811) qf button (power) 8 connector (CN805)
  • Page 15: I/O Board, Tuner

    HCD-DX315 3 7 63 1515 0 3-5. I/O BOARD, TUNER 5 wire (flat type) 3 tuner 9core(CN203) qa I/O board 4 connector 1 two screws (CN312) (+BVTT 3 × 6) 6 wire (flat type) 2 wire (flat type) 13core(CN311)
  • Page 16: Main Board

    HCD-DX315 3 7 63 1515 0 3-7. MAIN BOARD 6 wire (flat type) 13core (CN1301) When assembling, 7 connector clamp the three harnesses with 5 wire (flat type) 7core (CN1302) (CN303) a lead pin or a similar tool so 8 connector that they do not touch this screw.
  • Page 17: Power Board

    HCD-DX315 3 7 63 1515 0 3-8. POWER BOARD 6 five screws (+PWH 3 × 8) 7 POWER board 4 two screws (+BV 3) 5 shield (H/L) 1 connector (CN515) 2 connector (CN3002) 3 connector (CN901) L 13942296513 When re-assembling, leave 30 mm between harnesses A and B for safety.
  • Page 18: Dvd Mechanism Deck (Cdm81C-Dvbu101)

    HCD-DX315 3 7 63 1515 0 3-9. DVD MECHANISM DECK (CDM81C-DVBU101) 3 four screws (+BV 3) 4 MD COVER 2 Remove the harness and flexible cable. harness flexible cable L 13942296513 1 wire (flat type) 21core (CN508) 5 four screws (+BVTP 3 ×...
  • Page 19: Tray

    HCD-DX315 3 7 63 1515 0 3-10. TRAY 2 two screws (+BTTP 2.6) 1 two screws 3 bracket (+BTTP 2.6) 5 tray L 13942296513 3-11. MOTOR BOARD M761 (LD/ST MOTOR), M762 (BU U/D MOTOR) 1 screw (+BTTP 2.6) 3 screw (+BTTP 2.6)
  • Page 20: Base Unit (Dvbu101)

    HCD-DX315 3 7 63 1515 0 3-12. BASE UNIT (DVBU101) 1 two floating screws (+PTPWH2.6) 3 base unit (DVBU101) 2 floating screw (+PTPWH2.6) L 13942296513 3-13. OPTICAL PICK-UP (KHM-310CAB) qa insulator 7 insulator screw 3 insulator screw qs insulator...
  • Page 21: Gear (Sub Tray 1), Gear (Sub Tray 2)

    HCD-DX315 3 7 63 1515 0 3-14. GEAR (SUB TRAY 1), GEAR (SUB TRAY 2) PRECAUTION DURING GEAR (SUB TRAY 1/2) INSTALLATION 1 five screws (+PTPWH 2.6 × 8) Align the marks of the gears as shown in the illustration.
  • Page 22: Stocker Section

    HCD-DX315 3 7 63 1515 0 3-16. STOCKER SECTION 2 stocker section 1 Rotate the gear (SS3) in the direction of the arrow. L 13942296513 3-17. CAM (STOCKER) PRECAUTION DURING CAM (STOCKER) INSTALLATION Before installing the cams (stocker), fix the gear (stocker 3) in...
  • Page 23: Gear (Stocker 3)

    HCD-DX315 Ver. 1.2 3 7 63 1515 0 3-18. GEAR (STOCKER 3) PRECAUTION DURING GEAR (STOCKER 3) INSTALLATION 1 screw (+PTPWH 2.6 × 8) Be sure to align the rib of the gear (stocker 3) with the groove of the rotary encoder.
  • Page 24: Gear (Bu2)

    HCD-DX315 Ver. 1.2 3 7 63 1515 0 3-20. GEAR (BU2) 1 belt (sub tray) PRECAUTION DURING GEAR (BU2) INSTALLATION 4 screw 2 screw Before re-assembling, slide the cam (BU) in the direction of (+PTPWH 2.6 × 8) (+PTPWH 2.6 × 8) the arrow.
  • Page 25: Test Mode

    HCD-DX315 Ver. 1.1 SECTION 4 3 7 63 1515 0 TEST MODE 3. Disc Tray Lock Note 1: Regarding the notification symbol “R” The disc tray lock function for the antitheft of an demonstration Because the number of the operating buttons of this product disc in the store is equipped.
  • Page 26 HCD-DX315 Ver. 1.1 3 7 63 1515 0 (2) Select “2. Drive Manual Operation” by pressing the 2 “R” DVD SECTION button on the remote commander. The screen will appear as shown. 8-1. GENERAL DESCRIPTION The IOP measurement allows you to make diagnosis and adjustment Drive Manual Operation simply by using the remote commander and monitor TV.
  • Page 27 HCD-DX315 Ver. 1.1 3 7 63 1515 0 8-4. EMERGENCY HISTORY The meaning of error code is as below: To check the emergency history, please follow the following 01: Communication error (No reply from syscon) procedure. 02: Syscon hung up 03: Power OFF request when syscon hung up (1) From the Top Menu of Remocon Diagnosis Menu, select “3.
  • Page 28 HCD-DX315 Ver. 1.1 3 7 63 1515 0 8-4-4. Return to the Top Menu of Remocon Diagnosis Menu Press 0 “R” button on the remote commander. • Check Version Information To check the version information, please follow the following procedure.
  • Page 29: Electrical Adjustment

    HCD-DX315 Ver. 1.1 SECTION 5 3 7 63 1515 0 ELECTRICAL ADJUSTMENT Checking Location: MAIN board (Side A) DVD SECTION MAIN BOARD (SIDE A) When the base unit is replaced, perform the adjustment and the measurement as shown below in this order.
  • Page 30: Diagrams

    HCD-DX315 SECTION 6 3 7 63 1515 0 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Dia grams. For Printed Wiring Boar ds.
  • Page 31 HCD-DX315 3 7 6 3 1 5 1 5 0 • Circuit Boards Location • Waveforms – MAIN Board – – I/O Board – IC1101 6 (DVDRFIP) IC201 wd (CVBS) IC201 w; (CYOUT) 2.5 Vp-p 2.2 Vp-p TUNER UNIT...
  • Page 32: Block Diagram - Rf Section

    HCD-DX315 6-1. BLOCK DIAGRAM – RF SECTION – 3 7 6 3 1 5 1 5 0 • Signal Path CN1105 : CD PLAY RFMON V2REFO DVDRFIP V2REFO : DVD PLAY TO DIAG JIG : SACD PLAY DVDA DVDB...
  • Page 33: Block Diagram - Amp Section

    HCD-DX315 6-2. BLOCK DIAGRAM – AMP SECTION – 3 7 6 3 1 5 1 5 0 IC352 AUDIO INPUT SELECTOR IC353 11 X3 IC401 IC2200 15 X2 A/D CONVERTER L-CH 14 X1 – 1 LIN BOUT J401 –...
  • Page 34: Block Diagram - Audio Section

    HCD-DX315 6-3. BLOCK DIAGRAM – AUDIO SECTION – IC3001 3 7 6 3 1 5 1 5 0 COMPARATOR J402 – PHONES – PLUG DET2 Q450,451 HPMUTE Q3081 Q460,461 MUTE SW IC3500 MUTE S-MASTER DIGITAL AMP • Signal Path...
  • Page 35: Block Diagram - Video Section

    HCD-DX315 6-4. BLOCK DIAGRAM – VIDEO SECTION – 3 7 6 3 1 5 1 5 0 IC201 VIDEO AMP, 75Ω DRIVE YUV2 2 CIN J201 COUT S VIDEO 6 YIN YUV1 (DVD ONLY) YOUT YUV3 4 CVBSIN VIDEO...
  • Page 36: Block Diagram - Power Section

    HCD-DX315 6-5. BLOCK DIAGRAM – POWER SECTION – 3 7 6 3 1 5 1 5 0 POWER Thermistor F901 T901 D901 TRANSFORMER(MAIN) AC IN LINE FILTER D931 IC901 D905 +31.5V Q901 T801 POWER VOLTAGE DC/DC PROTECTION CONTROLLER IC931...
  • Page 37: Printed Wiring Board - Main Board (Side A)

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-6. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 New part of EEP ROM (IC1103) on the MAIN board cannot be used.
  • Page 38: Printed Wiring Board - Main Board (Side B)

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-7. PRINTED WIRING BOARD – MAIN BOARD (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 POWER BOARD JACK BOARD CN902 POWER BOARD CN403...
  • Page 39: Schematic Diagram - Main Board (1/10)

    HCD-DX315 • See page 58 for IC Block Diagrams. 6-8. SCHEMATIC DIAGRAM – MAIN BOARD (1/10) – 3 7 6 3 1 5 1 5 0 (CHASSIS) EB3001 TERMINAL BOARD MAIN BOARD (2/10) (Page 40) R3060 R3062 R3063 R3064...
  • Page 40: Schematic Diagram - Main Board (2/10)

    HCD-DX315 6-9. SCHEMATIC DIAGRAM – MAIN BOARD (2/10) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (1/10) (Page 39) ICT3010 C3406 C3403 0.033 ICT3011 C3551 1 50V ICT3060 R3061 R3403 TP3410 C3413 C3412 R3404 R3551...
  • Page 41: Schematic Diagram - Main Board (3/10)

    HCD-DX315 • See page 31 for Waveform. • See page 58 for IC Block Diagrams. 6-10. SCHEMATIC DIAGRAM – MAIN BOARD (3/10) – 3 7 6 3 1 5 1 5 0 R3055 C3015 C3014 R3011 470 1/10W R3050...
  • Page 42: Schematic Diagram - Main Board (4/10)

    HCD-DX315 6-11. SCHEMATIC DIAGRAM – MAIN BOARD (4/10) – 3 7 6 3 1 5 1 5 0 Q3202 Q3252 2SA1235TP-1EF 2SA1235TP-1EF ICT3027 C3206 C3203 0.033 Q3201 Q3251 2SA1235TP-1EF ICT3028 2SA1235TP-1EF R3203 C3213 TP3210 C3212 C3221 C3271 R3204 R3207...
  • Page 43: Schematic Diagram - Main Board (5/10)

    HCD-DX315 • See page 31 for Waveform. • See page 60 for IC Pin Function Description. 6-12. SCHEMATIC DIAGRAM – MAIN BOARD (5/10) – 3 7 6 3 1 5 1 5 0 R524 R624 CN507 C856 FFC-S-1.0 R593 RDS_DATA.
  • Page 44: Schematic Diagram - Main Board (6/10)

    HCD-DX315 6-13. SCHEMATIC DIAGRAM – MAIN BOARD (6/10) – 3 7 6 3 1 5 1 5 0 C582 IC516 IC TA7805LS C580 2200 6.3V C601 C602 C603 100 10V C517 0.001 C525 C506 C598 C510 0.33 C511 R506...
  • Page 45: Schematic Diagram - Main Board (7/10)

    HCD-DX315 6-14. SCHEMATIC DIAGRAM – MAIN BOARD (7/10) – 3 7 6 3 1 5 1 5 0 IC1107 TK11133CSC L-G ICT1129 C1193 C1195 0.22 0.22 C1192 FL1101 0.01 25V B C1101 CN1101 0.01 JL1139 C1120 1 10V B...
  • Page 46: Schematic Diagram - Main Board (8/10)

    HCD-DX315 • See page 31 for Waveforms. • See page 63 for IC Pin Function Description. 6-15. SCHEMATIC DIAGRAM – MAIN BOARD (8/10) – 3 7 6 3 1 5 1 5 0 R2120 R2121 R2122 R2123 C1163 R2124...
  • Page 47: Schematic Diagram - Main Board (9/10)

    HCD-DX315 6-16. SCHEMATIC DIAGRAM – MAIN BOARD (9/10) – 3 7 6 3 1 5 1 5 0 New part of EEP ROM (IC1103) on the MAIN board cannot be used. Therefore, if the mounted MAIN board (A-1179-147-A) is replaced, exchange new EEP ROM (IC1103) with that used before the replacement.
  • Page 48: Schematic Diagram - Main Board (10/10)

    HCD-DX315 6-17. SCHEMATIC DIAGRAM – MAIN BOARD (10/10) – 3 7 6 3 1 5 1 5 0 R1234 ICT550 R1223 R1225 100k 100k 1/10W 1/10W 0.5% 0.5% C1209 R1230 0.033 1/10W C1228 C1212 0.5% 0.0047 0.01 R1221 1/10W 0.5%...
  • Page 49: Printed Wiring Board - I/O Board

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-18. PRINTED WIRING BOARD – I/O BOARD – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor J202 COMPONENT Location VIDEO OUT Ref. No. Location...
  • Page 50: Schematic Diagram - I/O Board

    HCD-DX315 • See page 31 for Waveforms. • See page 58 for IC Block Diagrams. 6-19. SCHEMATIC DIAGRAM – I/O BOARD – 3 7 6 3 1 5 1 5 0 CN203 CN312 AMP-S 5P C345 R381 R382 TP353...
  • Page 51: Printed Wiring Boards - Panel Section

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-20. PRINTED WIRING BOARDS – PANEL SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MAIN BOARD CN509 (Page 37) JR807 CN805 FL801 CN801 IC801...
  • Page 52: Schematic Diagram - Panel Section

    HCD-DX315 • See page 58, 59 for IC Block Diagrams. 6-21. SCHEMATIC DIAGRAM – PANEL SECTION – 3 7 6 3 1 5 1 5 0 Q814 Q815 RT1P141C-TP-1 RT1P141C-TP-1 R835 R834 R833 R836 D812 D813 SML79423C-TP15 SML79423C-TP15 R852...
  • Page 53: Printed Wiring Board - Speaker Board

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-22. PRINTED WIRING BOARD – SPEAKER BOARD – 6-23. SCHEMATIC DIAGRAM – SPEAKER BOARD – 3 7 6 3 1 5 1 5 0 :Uses unleaded solder. EP301 EARTH PLATE...
  • Page 54: Printed Wiring Boards - Cd Mechanism Section

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-24. PRINTED WIRING BOARDS – CD MECHANISM SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor MOTOR BOARD Location Ref. No. Location D701...
  • Page 55: Schematic Diagram - Cd Mechanism Section

    HCD-DX315 6-25. SCHEMATIC DIAGRAM – CD MECHANISM SECTION – • See page 59 for IC Block Diagrams. 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 (5/10) CN508...
  • Page 56: Printed Wiring Board - Power Board

    HCD-DX315 • See page 31 for Circuit Boards Location. 6-26. PRINTED WIRING BOARD – POWER BOARD – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor (CHASSIS) Location R969 Ref. No. Location D907 D906...
  • Page 57: Schematic Diagram - Power Board

    HCD-DX315 6-27. SCHEMATIC DIAGRAM – POWER BOARD – 3 7 6 3 1 5 1 5 0 (CHASSIS) EB905 D931 FCU20UC20 C938 330p CN902 250V TP903 WIRE 3P C930 CN901 C963 FH901 FH902 100p 0.0022 TH901 HOLDER HOLDER LF902...
  • Page 58 HCD-DX315 3 7 6 3 1 5 1 5 0 • IC Block Diagrams – MAIN Board – – MAIN Board – – LED Board – IC3050 TK11118CSCL-G IC803 BU2099FV IC2200 PCM1803DBR 17 16 15 14 13 12 12 BIT...
  • Page 59 HCD-DX315 3 7 63 1515 0 – FL Board – IC802 PT6315 Grid driver Multiplexed driver SEG19/GRID10 Command decoder LED1 SEG18/GRID11 LED2 Display memory LED3 SEG17/GRID12 24 bits x 12 words LED4 Timing generator key scan DOUT SEG16/KS16 Key data memory...
  • Page 60 HCD-DX315 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC501 M30622MEP-A61FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP_SCDT/ DAMP processor and Diat data output DIAT_SDATA DAMP_SHIFT/ DAMP processor and Diat clock output DIAT_SCLK DSP_INTR...
  • Page 61 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description DRIVE_OCP (DIAG) DAMP driver shut down OVERFLOW1 DAMP processor F/C/S over flow detect OVERFLOW2 DAMP processor SW over flow detect WRITE CE Flash write CE (Pull up) DAMP LATCH1...
  • Page 62 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description IO_DO I/O expander IC data input IO_CLK I/O expander IC clock output MONO/ST_DET Front jack MONO or STEREO detect A.CAL MIC LEVEL MIC level detect for auto calibration...
  • Page 63 HCD-DX315 3 7 63 1515 0 MAIN BOARD IC1101 CXD9849R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Ground terminal DVDA AC coupled input path A DVDB AC coupled input path B...
  • Page 64 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description DSEL — Not used WIDE Wide switch signal input terminal Mute signal control input MAMUTE MAMUTE signal output to system controller (IC501) (not used) DVDD18 — Power supply (+1.8V from IC1109)
  • Page 65 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description DQMO DQM0 signal output to SD-RAM (IC1104) MREQ DQM signal input (not used) Data bus 7 from SD-RAM (IC1104) DVSS — Ground terminal 117, 118 RD 6, 5...
  • Page 66 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description LIMSW LIMSW signal output to optical pick-up OCSW SEN signal input from system controller (IC501)/OCSW signal input (not used) REW signal output to IC1201 CKSW CKSW signal input (not used) —...
  • Page 67 HCD-DX315 3 7 63 1515 0 Pin No. Pin Name Description SDPIF — SPDIF output (not used) RFGND18 — Ground terminal RFVDD18 — Power supply (RF+1.8V) XTALO Oscillator output signal (27MHz) XTALI Oscillator input signal (27MHz) JITFO RF jitter meter output...
  • Page 68: Exploded Views

    HCD-DX315 SECTION 7 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 69: Front Panel Section

    HCD-DX315 3 7 63 1515 0 7-2. FRONT PANEL SECTION supplied supplied supplied supplied S800 L 13942296513 (Refer to page 78) including S800 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-654-836-01 KNOB (VOL) 2-653-091-01 BUTTON (DISC)
  • Page 70: Chassis Section

    HCD-DX315 3 7 63 1515 0 7-3. CHASSIS SECTION supplied not supplied supplied 103 104 supplied F901 supplied DVD mechanism deck section supplied L 13942296513 supplied not supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No.
  • Page 71: (Cdm81C-Dvbu101)

    HCD-DX315 3 7 63 1515 0 7-4. DVD MECHANISM DECK SECTION-1 (CDM81C-DVBU101) L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-251-849-01 LEVER (SW2) 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 4-251-991-01 SPRING (SW2), TORSION 4-251-923-01 YOKE (310)
  • Page 72: Dvd Mechanism Deck Section-2 (Cdm81C-Dvbu101)

    HCD-DX315 Ver. 1.2 3 7 63 1515 0 7-5. DVD MECHANISM DECK SECTION-2 (CDM81C-DVBU101) not supplied not supplied M761 M762 L 13942296513 S771 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark...
  • Page 73: Dvd Mechanism Deck Section-3 (Cdm81C-Dvbu101)

    HCD-DX315 3 7 63 1515 0 7-6. DVD MECHANISM DECK SECTION-3 (CDM81C-DVBU101) not supplied CDM81C-DVBU101 not supplied L 13942296513 not supplied S781 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING...
  • Page 74: Base Unit (Dvbu101)

    HCD-DX315 3 7 63 1515 0 7-7. BASE UNIT (DVBU101) L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4956-097-1 HOLDER (310) ASSY 3-087-599-01 INSULATOR SCREW 0 302 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP) 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S...
  • Page 75: Electrical Parts List

    HCD-DX315 SECTION 8 3 7 63 1515 0 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, uH: µH parts list may be different from the parts please include the board name.
  • Page 76 HCD-DX315 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1176-129-A I/O BOARD, COMPLETE < IC > ******************* IC201 6-705-602-01 IC MM1623BFBE < CAPACITOR > IC352 8-759-385-76 IC MC14052 BDR2 IC353...
  • Page 77 HCD-DX315 JACK 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R356 1-216-829-11 METAL CHIP 4.7K 1/10W D497 6-501-193-01 DIODE 1SS355WTE-17 R357 1-216-829-11 METAL CHIP 4.7K 1/10W R358 1-216-841-11 METAL CHIP 1/10W <...
  • Page 78 HCD-DX315 JACK MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q814 8-729-027-23 TRANSISTOR RT1P141C-TP-1 R422 1-216-837-11 METAL CHIP 1/10W Q815 8-729-027-23 TRANSISTOR RT1P141C-TP-1 R423 1-216-821-11 METAL CHIP 1/10W R424...
  • Page 79 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1130 1-107-826-11 CERAMIC CHIP 0.1uF C507 1-107-826-11 CERAMIC CHIP 0.1uF C1131 1-125-838-11 CERAMIC CHIP 2.2uF 6.3V C508 1-162-964-11 CERAMIC CHIP 0.001uF...
  • Page 80 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3037 1-164-156-11 CERAMIC CHIP 0.1uF C1209 1-164-677-11 CERAMIC CHIP 0.033uF C3038 1-164-156-11 CERAMIC CHIP 0.1uF C1210 1-162-970-11 CERAMIC CHIP 0.01uF...
  • Page 81 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3273 1-162-964-11 CERAMIC CHIP 0.001uF C3154 1-164-156-11 CERAMIC CHIP 0.1uF C3300 1-104-329-11 CERAMIC CHIP 0.1uF C3155 1-107-725-11 CERAMIC CHIP 0.1uF...
  • Page 82 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB501 1-469-324-21 FERRITE, EMI (SMD) (2012) C3551 1-126-960-11 ELECT FB502 1-469-324-21 FERRITE, EMI (SMD) (2012) C3552 1-126-964-11 ELECT 10uF FB503...
  • Page 83 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JC515 1-216-864-11 SHORT CHIP R585 1-216-809-11 METAL CHIP 1/10W R586 1-216-809-11 METAL CHIP 1/10W < COIL > R587 1-216-809-11 METAL CHIP...
  • Page 84 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1180 1-216-805-11 METAL CHIP 1/10W R739 1-216-833-11 METAL CHIP 1/10W R1181 1-216-805-11 METAL CHIP 1/10W R741 1-216-833-11 METAL CHIP 1/10W...
  • Page 85 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3062 1-216-809-11 METAL CHIP 1/10W R2203 1-216-817-11 METAL CHIP 1/10W R3063 1-216-821-11 METAL CHIP 1/10W R2211 1-216-809-11 METAL CHIP 1/10W...
  • Page 86 HCD-DX315 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3403 1-216-797-11 METAL CHIP 1/10W R3171 1-216-833-11 METAL CHIP 1/10W R3404 1-216-864-11 SHORT CHIP R3172 1-216-833-11 METAL CHIP 1/10W R3407...
  • Page 87 HCD-DX315 MOTOR POWER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MOTOR BOARD C967 1-100-566-91 CERAMIC CHIP 0.1uF C968 1-100-566-91 CERAMIC CHIP 0.1uF ************* C969 1-100-566-91 CERAMIC CHIP 0.1uF < SWITCH >...
  • Page 88 HCD-DX315 POWER RELAY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > R943 1-216-864-11 SHORT CHIP R946 1-216-811-11 METAL CHIP 1/10W L931 1-457-226-11 INDUCTOR 10uH R948 1-216-833-11 METAL CHIP...
  • Page 89 HCD-DX315 RELAY SENSOR SPEAKER SW (1) SW (2) 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R711 1-249-415-11 CARBON 1/4W ************************************************************* R712 1-247-807-31 CARBON 1/4W R751 1-247-806-11 CARBON 1/4W SW BOARD...
  • Page 90 HCD-DX315 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page.

Table of Contents