Zipato Z-Wave PH-PSG01 Quick Installation Manual

SMOKE
SENSOR
QUICK INSTALLATION GUIDE
v1.0
TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the
content of this manual, it is possible that this document may
contain technical inaccuracies, typographical, or other errors.
Zipato assumes no liability for any error in this publication, and for
damages, whether direct, indirect, incidental, and consequential
or otherwise, that may result from such error, including, but not
limited to loss of data or profits. Zipato provides this publication
"as is" without warranty of any kind, either express or implied,
including, but not limited to implied warranties of merchantability
or fitness for a particular purpose. The published information in
the manual is subject to change without notice.Zipato reserves the
right to make changes in the product design, layout, and driver
revisions without notification to its users. This version of the
Installation guide supersedes all previous versions.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies with
all the requirements in respect of interference radiation according
to EN 301 489-17, EN 301 489-3 and EN 300 328. The connections
conducting HF signals must neither be manipulated nor damaged.
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer's instructions. Be careful when using hand
and power tools and follow the manufacturer's guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
INTRODUCTION
Zipato Smoke Sensor (Z-Wave) is designed to give early warning
of developing fires by giving off the alarm sounds from its build-in
alarm horn, based on Z-Wave technology. Zipato Smoke Sensor is
Z-Wave Plus product, it supports security, OTA and all other new
features of 500 Series Z-Wave chipset.
Z-Wave is a wireless communication protocol designed for remote
control of appliances in residential automated homes and light
commercial enviroments.It can be used with lightning systems,
home access control, entertainment systems and house appliances.
This product can be included and operated in any Z-Wave network
with other Z-Wave certified devices from other manufacturers and/
or other applications. All non-battery operated nodes within
the network will act as repeaters regardless of vendor to increase
reliability of the network.
The device is based on Z-Wave 500 series chip, and has advantages
as below:
• Concurrent multi-channel support reduces external interference.
• Better RF range, about 10 meters improvement indoors.
• Supports 100 Kbps transmission speeds.
make your home smart
OVERVIEW
PACKAGE CONTENT
1PC Smoke sensor
1PC Screws pack
1PC Quick Installation Guide
FEATURES
Smoke detection
New Z-Wave 500 series chip brings better RF range indoors and
up to 100 Kbps transmission speeds
Higher output power to enhance the communication range
(+5dBm output power as compared to -2.5dBm 300 series)
Built-in sound alarm
Over-the-air firmware update
Low battery auto report
Low power consumption
Low power indication
Easy installation and rellocation
Removable ceiling bracket
Slim, elegant design
SPECIFICATION
TECHNICAL SPECIFICATION
PROTOCOL Z-Wave 500 series
POWER CR123A lithium battery, 1400mAh
OPERATING VOLTAGE
OPERATING CURRENT 90 mA
STANDBY CURRENT 20 uA
RANGE Minimum 30m indoor, 70m outdoor line of sight
OPERATING TEMPERATURE 0 ° C ~ 40 ° C
DIMENSION 120 x 120 x 14 mm
WEIGHT 150g
USE Indoor use only
WARRANTY 1 year
MODEL AND FREQUENCIES
EUROPEAN UNION - EU version ph-psg01.eu / 868.42MHz
UNITED STATES - US version ph-psg01.us / 908.42MHz
RUSSIA - RU version ph-psg01.ru / 869.00MHz
ISRAEL - IS version ph-psg01.is / 916.00MHz
AUSTRALIA - AU version ph-psg01.au / 921.42MHz
INDIA - IN version ph-psg01.in / 865.22MHz
JAPAN - JP 922~926 MHZ
INSTALLATION & OPERATION
www.zipato.com
BATTERY INSTALLATION
If your controller receives low battery alarm, it means that Smoke
Sensor's battery is weak. When the device report the low battery
message user should replace the battery. The battery type is
CR123A, 3.0V.
To open the front cover please follow below steps:
1 | Open battery compartment.
2 | Install battery into compartment and make sure the "+" and
"-"ends of each battery are aligned properly.
3 | After battery is installed in compartment, you will hear a chirp
which indicates the device is receiving battery power.
Removable cover of
smoke chamber
CHOOSING A SUITABLE LOCATION
For complete coverage in residential units, Smoke Sensors should
be installed in all rooms, halls, storage areas, basements and attics
in each family living unit. Minimum coverage is one sensor on each
floor and one in each sleeping area.
1 | Install Smoke Sensor as close to the center of ceiling as
possible. If this is not practical, put the sensor on the ceiling,
no closer than 4 inches (10 cm) from any wall or corner.
2 | If ceiling mounting is not possible, put wall-mounted sensors
between 4 and 6 inches (10~15 cm) from the ceiling.
3 | If some of your rooms have sloped, peaked, or gabled ceilings,
try to mount sensors 3 feet (0.9 meter). Measure horizontally
from the highest point of ceiling.
Dining room Kitchen
Living room
Smoke sensors for maximum security
Bedroom Kitchen Bedroom
Living room
3V
Bedroom Smoke sensors for minimum security
Nuisance alarms take place when Smoke Sensors are installed
where they will no longer work properly. To avoid nuisance
alarms, do not install Smoke Sensors in the following situations:
Combustion particles are by-products of something that is
burning. Thus, don't install Smoke Sensors in or near areas
where combustion particles are present to avoid nuisance
alarms, such as kitchens with few windows or poor ventilation,
garages where there may be vehicle exhaust, near furnaces, hot
water heaters, and space heaters.
Do not install Smoke Sensors less than 20 feet (6 meters) away
from places where combustion particles are normally present,
like kitchens.
If a 20-foot distance is not possible, e.g. in a mobile home, try to
install the alarm as far away from the combustion particles as
make your home smart
possible, preferably on the wall. To prevent nuisance alarm alarms,
provide good ventilation in such places.
In very dusty or dirty areas, dirt and dust can build up on the
alarm's sensing chamber, possibly making it overly sensitive.
Additionally, dust or dirt can block openings to the sensing
chamber and possibly lowering alarm's sensing efficiency.
Near fluorescent lights, electrical "noise" from fluorescent lights
may cause nuisance alarms. Install Smoke Sensor at least 5 feet
(1.5 meters) from such lights.
MOUNTING
1 | At the place where you are going to install your Smoke Sensor,
draw a horizontal line six inches long.
2 | Remove the mounting bracket from your device by rotating it
counterclockwise.
3 | Place the bracket so that the two lon-gest hold slots are
aligned on the line. In each of keyhole slots, draw a mark to
locate a mounting plug and do the screwing.
4 | Remove the bracket.
Tamper 5 | Drill two holes at the marks and insert plastic wall plugs. Put
Switch the Smoke Sensor away from plastic dust.
6 | Attach the bracket to the wall. Line up the slots of the bracket
and the Smoke Sensor. Push the sensor onto the mounting
bracket and turn it clockwise to fix it into the place. Pull
onward on the Smoke Sensor to make sure it is securely
attached to the mounting bracket.
Mounting
bracket
ADDING TO Z-WAVE NETWORK
Bedroom
For the first time, you must join the device to Z-Wave network. First,
make sure the primary controller is in the adding/inclusion mode.
And then power on the device, and then insert battery to power on
the device. Press the test button once to start the NWI (Network
Bedroom
Wide Inclusion) mode, and it should be included in 5 seconds.
Notice: Including a node ID allocated by Z-Wave Controller means
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
Bedroom
Notice: Including a node ID allocated by Z-Wave Controller means
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
FUNCTION DESCRIPTION
1. Have Z-Wave Controller entered inclusion
Bedroom
mode.
2. Press test button three times within 1.5
Add seconds to enter the inclusion mode.
3. After the adding was successful, the device
will wake to receive the setting mand from
Z-Wave Controller about 20 seconds.
1. Have Z-Wave Controller entered inclusion
mode.
Remove 2. Pressing test button three times within 1.5
seconds to enter the exclusion mode. Node ID
has been removed.
Notice: Use this procedure only in the event
that the primary controller is lost or otherwise
inoperable.
1. Have Z-Wave Controller entered inclusion
Reset mode.
2. After the red LED flash 9 times, release the
test button within 2 seconds.
3. IDs are removed and all settings will reset to
factory default.
www.zipato.com
Test / Silence
Button & Power
/ Smoke Alarm
LED indicator
02