Subscribe to Our Youtube Channel
Related Manuals for Sunrise JAY ConfigureFit
Summary of Contents for Sunrise JAY ConfigureFit
- Page 1 ConfigureFit ® ™ Instruction Manual Important Consumer Information Notice: This packet contains instructions that must be passed on to the user of this product. Please do not detach this packet before delivery to the end user.
-
Page 3: Introduction
SUNRISE LISTENS SUNRISE LISTENS Thank you for choosing a Sunrise ConfigureFit System. We want to hear your questions or comments about this manual, the safety and reliability of your seating system and the service you receive from your Sunrise supplier. -
Page 4: Table Of Contents
TABLE OF CONTENTS Introduction ..............1 General Seating System & Warnings ........3 Attaching the Hardware ............9 Testing the Seating System Fit to the Wheelchair ....11 Seating System Component Adjustment ......12 Cleaning and Maintenance ..........15 Warranty ................16 116083... -
Page 5: General Seating System & Warnings
READ BEFORE USE A. CHOOSE THE RIGHT SEAT & SAFETY OPTIONS Sunrise provides a choice of many wheelchair seats to meet the needs of the wheelchair user. Final selection on the type of seat, options and adjustments should be made with your health care advisor and authorized Sunrise supplier: 1. - Page 6 2. Consult your authorized supplier BEFORE you modify or adjust your seat. 3. We recommend that you use anti-tip tubes . 4. Unauthorized modifications or use of parts not supplied or approved by Sunrise may change the seat structure. This will void the warranty and may cause a safety hazard.
- Page 7 GENERAL SEATING SYSTEM AND WHEELCHAIR WARNINGS E. ENVIRONMENTAL CONDITIONS 1. Contact with water or excess moisture may cause your seat to rust, degrade or corrode. This could cause your seat to fail. a. Do not use your seat in a shower, pool or other body of water. b.
- Page 8 GENERAL SEATING SYSTEM AND WHEELCHAIR WARNINGS e. Never allow the presence of a second occupant climbing or standing on a component of the chair. If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and cause severe injury to the rider or others.
- Page 9 3. If bolts or screws become loose, tighten them as soon as you can. 4.Sunrise recommends that all fasteners be checked for wear, such as loose bolts or broken components every 3 months. Loose fasteners should be retightened according to the installation instructions.
- Page 10 GENERAL SEATING SYSTEM AND WHEELCHAIR WARNINGS seat. Consult with the user’s doctor, nurse or therapist to find out if the rider needs this contour when constructing the seat. 4. Use positioning belts only with a user who can cooperate. Make sure the user can easily remove the belts in an emergency.
-
Page 11: Attaching The Hardware
(t-nut) is not dislodged. Ensure that all threads align straight and do not cross thread. Tighten all fasteners. Sunrise recommends tightening fasteners to 100 ft/lbs (115.5 kgf/cm) of torque. STEP-1 ASSEMBLING THE BACK TO SEAT BRACKET TO THE SEATING SYSTEM. - Page 12 ATTACHING THE HARDWARE STEP-3 ASSEMBLING THE SEAT TABS TO THE SEATING SYSTEM. a. Attach the Seat Tabs (D) to the seat so they rest on the wheelchair seat tube. fig. #5 STEP-4 ATTACHING THE SEAT AND BACK HOOKS W A R N I N G The seat and back hooks must only be attached in the areas shown on (figs 6 &...
-
Page 13: Testing The Seating System Fit To The Wheelchair
TESTING THE SEATING SYSTEM FIT TO THE WHEELCHAIR TESTING THE SEATING SYSTEM FIT TO THE WHEELCHAIR Check the attachment of the seating system to the wheelchair as shown in (fig. 8). MAKE CERTAIN THE FOLLOWING HAPPENS: A. The back hooks and seat hooks slide totally onto the knob hardware. B. -
Page 14: Seating System Component Adjustment
SEATING SYSTEM COMPONENT ADJUSTMENT SEATING SYSTEM ADJUSTMENTS Depending on the installed hardware and the system configuration your SUNRISE CONFIGUREFIT SYSTEM has a range of adjustments for growth, sizing and user support. The adjustments are available via: • The slotted design of most attaching and support hardware •... - Page 15 SEATING SYSTEM COMPONENT ADJUSTMENT BACK TO SEAT BRACKET: The back to seat bracket adjusts seat depth and back height (fig #10) fig. #10 KNOB CLAMPS – SEAT AND BACK: The slotted surfaces of the Knob Clamps adjust for seat and back depth, angle, and width. (fig #11) fig.
- Page 16 SEATING SYSTEM COMPONENT ADJUSTMENT THORACIC LATERALS AND HIP GUIDES w/o TRACKS: Depending on the choice of hardware thoracic laterals offer height, medial lateral adjustment along with angle and depth adjustment (fig# 13). NOTE: T-Nut adjustments – Locate the T-Nuts under the upholstery ensuring they are in the correct adjustment location and will line up with the hardware parts.
-
Page 17: Cleaning And Maintenance
IDENTIFYING LOOSE OR BROKEN COMPONENTS. FASTENERS: Sunrise recommends that all fasteners be checked for wear, such as loose bolts or broken components every 3 months. Loose fasteners should be retightened according to the installation instructions. All fasteners should be tightened to torque specifications as stated in the hardware installation instructions. -
Page 18: Warranty
SUNRISE MEDICAL CONFIGUREFIT SEATING SYSTEM WARRANTIES Sunrise Limited Warranty A. FOR LIFETIME Sunrise warrants the hardware items of this Custom Seating System against defects in materials and workmanship for the life of the original purchaser. The expected life of the hardware is five years. - Page 20 Sunrise Medical, Inc. 7477 East Dry Creek Pkwy Longmont, CO 80503 800.333.4000 www.sunrisemedical.com ©2009 Sunrise Medical, Inc. 12.09 116083 Rev. A...
Need help?
Do you have a question about the JAY ConfigureFit and is the answer not in the manual?
Questions and answers