Related Manuals for Harper VC-60
Summary of Contents for Harper VC-60
- Page 1 Vertical Mower Operator’s VC-60 Manual VC-60 Plus 8/11 Part No. 970066 VERTI-CUTTER...
- Page 2 VERTI-CUTTER...
- Page 3 MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your Goossen dealer or Harper Industries for clarification.
- Page 4 TWELVE MONTHS from the date of retail purchase to the original purchaser. Harper Industries will repair or replace, at our option, any part that our examina- tion shows to be defective. Warranty is limited to parts, labor and ground freight delivery of replacement parts.
-
Page 5: Table Of Contents
Hitch..............Blade Depth Adjustment........Hydraulic Cylinder..........Hydraulic Hoses..........Ram Stop............Gas Shock............Gearbox............Blades............... Chain Tension Adjustment........ VC-60 Plus Front Unit............Blade Rotation..........Rear Unit............Hydraulic Hose Splitter........Safety Guidelines Gards & Shields..........Safety Decals........... Equipment & Controls........Before Operation.......... -
Page 6: Blades
Length - 62” Height - 38” Width - 89” Harper Industries, Inc. is continually striving to improve the design and performance of its products. We reserve the right to make changes in specifications and design without thereby incurring any obligation relative to previously manufactured products. -
Page 7: Chain Tension Adjustment
VC - 60 Control Identification PTO SHAFT – transfers power from the tractor to the Verti-Cutter. SKID PLATES – control depth of blades and prevents the blades from gauging. HITCH – connects to tractor draw bar with standard 3/4” hitch pin. BLADE DEPTH ADJUSTMENT –... -
Page 8: Front Unit
REAR UNIT – PTO driven from the front unit. The blades are forward rotating. A tow The rear unit is the same as the VC-60 hitch is attached to its frame in order to expect that it has a shorter PTO shaft pull the rear unit. -
Page 9: Safety Guidelines
• New decals may be obtained from Safety Guidelines your local Harper/Goossen Dealer. Equipment & Controls SAFETY WARNING! • Altering this equipment in any manner Use genuine factory parts or parts with which adversely affects its operation, equivalent characteristics, including type, performance, durability, or use will void strength and material. -
Page 10: Operation
• The machine should be operated on stop. Disconnect the spark plug wire levelsurfaces only. from the spark plug or PTO shaft be- fore clearing debris. • Before starting the machine, visually inspect all nuts, bolts and other fasten- • Do not allow hands, clothing or any ers to see that they are properly part of the body to enter near any... -
Page 11: Hook Up & Operation
Starting Operation Hook Up & Operation 1. Engage PTO lever on the tractor AT IDLE SPEED of the tractor. SAFETY WARNING! 2. Lower machine with lever on tractor that • Wear approved eye and ear protec- controls auxiliary hydraulics and place in tion while operating the Verti-Cutter. -
Page 12: Adjustments
• The hitch bar is adjusted up or down Adjustments depending on which holes it is bolted into. Blade Depth • The hitch can be mounted in the top two holes to raise the hitch position or the bottom two holes to lower the hitch position. -
Page 13: Service & Maintenance
Standard Torque Chart Service & Maintenance Size In.-lb. Ft.-lb. No. 10-24 25-35 2.8-4.0 SAFETY WARNING! • Before servicing or inspecting the 1/4 in. 60-80 18-20 Verti-Cutter, make sure the power 5/16 in. 120-140 28-30 14-16 source is shut off and all parts have 3/8 in. - Page 14 VERTI-CUTTER...
-
Page 15: Parts Section
Vertical Mower Parts VC-60 Section VC-60 Plus 8/11 Part No. 970066 VERTI-CUTTER... - Page 16 VERTI-CUTTER...
- Page 17 VC -60 PARTS VERTI-CUTTER...
- Page 18 VERTI-CUTTER...
-
Page 19: Frame Assy
Shaft Assy............Blades............... Hydraulic Assy..........Shield Assy............PTO Shaft............Decal Kit, Complete.......... VC-60 PLUS Frame Assy. Front/Rear Unit......Wheel & Hub Assy Front/Rear Units....Shaft Assy Front Unit........Shaft Assy Rear Unit........Hydraulic Assy. Front Unit......... Hydraulic Assy. Rear Unit......... - Page 20 VERTI-CUTTER...
- Page 21 VERTI-CUTTER...
- Page 22 VERTI-CUTTER...
- Page 23 VERTI-CUTTER...
- Page 24 VERTI-CUTTER...
- Page 25 VERTI-CUTTER...
- Page 26 VERTI-CUTTER...
- Page 27 VERTI-CUTTER...
- Page 28 VERTI-CUTTER...
- Page 29 VC -60 PLUS PARTS VERTI-CUTTER...
- Page 30 VERTI-CUTTER...
- Page 31 VERTI-CUTTER...
- Page 32 VERTI-CUTTER...
- Page 33 VERTI-CUTTER...
- Page 34 VERTI-CUTTER...
- Page 35 VERTI-CUTTER...
- Page 36 VERTI-CUTTER...
- Page 37 VERTI-CUTTER...
- Page 38 VERTI-CUTTER...
- Page 39 VERTI-CUTTER...
- Page 40 VERTI-CUTTER 2.10...
- Page 41 VERTI-CUTTER 2.11...
- Page 42 NOTES VERTI-CUTTER...
- Page 43 Harper Industries, Inc. Telephone: 620-896-7381 151 E. Highway 160 Toll-Free: 800-835-1042 Harper, KS 67058 Fax: 620-896-7129 Website: www.harperindustries.com E-mail: info@harperindustries.com VERTI-CUTTER...
- Page 44 © 2011 Harper Industries, Inc. All rights reserved. Printed in U.S.A. VERTI-CUTTER...
Need help?
Do you have a question about the VC-60 and is the answer not in the manual?
Questions and answers