PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
TRANSISTOR ILLUSTRATION E C B B C E B C E E C B CSC4115BC 2SA1979O/Y 2SB1342 2SA952K KTA1266GR 2SC1815GR 2SB1370E KTC3198GR 2SD1933 E C B E C B 2SA1162GR DTA144TKA 2SC4115SRS 2SA1296GR 2SK2158 2SA1235F DTC114ES 2SK360E 2SC2712GR DTC144TKA 2SC2714O KRA107S DTA124EUA RT1P141C...
Page 25
IC DESCRIPTION IC, LC866548A Description Pin No. Pin Name I-ST/MO Tuner stereo input. I-TU/IFC Tuner TUNE IFC input. O-SOL Deck solenoid ON/OFF output. O-REC/PB Deck record/playback select output. O-MOTOR Deck motor ON/OFF control output. O-BIAS Record 85 kHz oscillaor ON/OFF output. O-MUTE Mute output.
Page 26
Description Pin No. Pin Name I-LW LW detect input. (Not used) I-SW SW detect input. (Not used) I-STOP Deck stop signal input. I-AS Auto stop signal input. I-WRQ CD WRQ input. I-DRF CD DRF input. Not connected. O-CD_ON CD ON/OFF control output. O-CD_CLOSE CD tray close output.
Page 27
IC, LA9241ML Pin No. Pin Name Description Connects to the pickup's photo diode; adding this pin to pin FIN1 generates RF signal, FIN2 and subtracting it generates FE signal. FIN1 Connects to the pickup's photo diode. Connects to the pickup's photo diode; subtracting this pin from pin F generates TE signal.
Page 28
Pin No. Pin Name Description CV– Input for CLV error signal from DSP. RFSM Output for RF. RFS– For setting RF gain and 3T compensation constant together with RFSM. SLICE LEVEL CONTROL; output for controlling the data slice level of DSP with RF waveform.
Page 29
IC, LC78622NE Pin No. Pin Name Description DEFI Defect detection signal (DEF) input. Test input. A pull-down resistor is built in. Must be connected to 0V. External VCO control phase comparator output. VVSS – Internal VCO ground. Must be connected to 0V. ISET PDO output current adjustment resistor connection.
Page 30
Pin No. Pin Name Description LCHO Left channel one-bit D/A converter output. LVSS – Left channel one-bit D/A converter ground. (Must be connected to 0V) RVSS – Right channel one-bit D/A converter ground. (Must be connected to 0V) RCHO Right channel one-bit D/A converter output. RVDD –...
Page 31
ADJUSTMENT <TUNER / DECK> < TUNER SECTION > 1. Clock Frequency Check 11. FM Separation Check Settings : • Test point : TP2 (CLK) Settings : • Test point : TP8 (Rch), TP9 (Lch) Method : Set to AM 1710 kHz and check that the test point is •...
CD TEST MODE 1. How to Activate CD Test Mode While pressing the CD function button, insert the AC plug to the outlet. All FL display will light up. 2. How to Cancel CD Test Mode Exit the CD test mode by any of the following procedures. •...
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 TOOLS Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units. 2 (() flat head screwdriver 3 Cut chisel How to Remove the PANEL, FR...
Page 41
SPEAKER PARTS LIST (SX-LM191<YJMN>) REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 8B-CP9-002-010 PANEL,FR 2 8B-CP9-003-010 RING,TW 3 8B-CP9-004-010 GRILLE,FRAME ASSY 4 8A-CL9-163-010 SPKR, CERAMIC 5 8A-CL9-164-010 CORD, SP SPEAKER PARTS LIST (SX-LM171<YJSN>) REF. NO. PART NO.
Page 42
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9820572 0251431 Printed in Singapore...