Related Manuals for Texas Instruments Tag-it RI-K01-320A
Summary of Contents for Texas Instruments Tag-it RI-K01-320A
- Page 1 ™ Tag-it Reader System Series 6000 Reader / Antenna Set RI-K01-320A (120 mW) RI-K02-320A (800 mW) Reference Guide 11-06-21-050 July 1999...
- Page 2 Demo Reader Set adjusted to ETSI limits (800 mW) RI-K02-320A Texas Instruments (TI) reserves the right to make changes to its products or services or to discontinue any product or service at any time without notice. TI provides customer assistance in various technical areas, but does not have full access to data concerning the use and applications of customer’s products.
-
Page 3: Read This First
PREFACE Read This First About This Manual This reference guide for the Tag-it Reader / Antenna Set is designed for use by TI partners who are engineers experienced with TIRIS and Radio Frequency Identification Devices (RFID). Regulatory and safety notes that need to be followed are given in Chapter 4. Conventions Certain conventions are used in order to display important information in this manual, these conventions are:... -
Page 4: Table Of Contents
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide Document Overview Chapter 1: Introduction ........................... 6 General ............................7 Tag-it System ..........................7 Chapter 2: Tag-it Reader / Antenna Set ......................8 Product Description ........................9 Functional Description......................10 Tag-it Navigator Software...................... - Page 5 July ′ 99 Preface List of Figures Figure 1 Tag-it System ..................7 Figure 2 Tag-it Reader / Antenna Set............9 Figure 3 Communication................10 Figure 4 Low Voltage Connector ..............11 Figure 5 Packing..................15 List of Tables Table 1 Specification Summary ..............14...
-
Page 6: Chapter 1: Introduction
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide CHAPTER 1 Chapter 1: Introduction Introduction Topic Page General ..................... 7 Tag-it System ................... 7... -
Page 7: General
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide General The Tag-it Reader / Antenna Set is intended to serve as a ready-to-use reader system for demonstration purposes or application installations where this particular form factor and performance is suitable. The read / write distance is determined by the size of the integrated antenna as well as by the power level that has been limited to meet emission constrains as required by the appropriate PTT approvals. -
Page 8: Chapter 2: Tag-It Reader / Antenna Set
CHAPTER 2 Chapter 2: Tag-it Reader / Antenna Set Tag-it Reader / Antenna Set Topic Page Product Description................9 Functional Description ..............10 Tag-it NavigatorTM Software ............10 Installation ..................11 2.4.1 What you will need..............11 2.4.2 Attaching Cables............... 11 2.4.3 References................ -
Page 9: Product Description
July ′ 99 Chapter 2. Tag-it Reader / Antenna Set Product Description The TIRIS Tag-it Reader / Antenna Set consists of an antenna box and a housed reader which is controlled by a host system to communicate with individual transponder tags. The host system can either be a PC, any other computer, or some other kind of intelligent device (e.g. -
Page 10: Functional Description
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide Functional Description Figure 3 Communication Communication Reader-to-Tag The frequency transmitted by RF Energy the antenna is used to supply the tag with operating energy DATA and to transmit data from Reader to Tag. -
Page 11: Installation
July ′ 99 Chapter 2. Tag-it Reader / Antenna Set Installation 2.4.1 What you will need • Linear regulated Power supply 12 V ± 5 % and min. 2 A with low voltage connector. Figure 4 Low Voltage Connector (dimensions in mm) 1.95 •... -
Page 12: Operation
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide Operation 2.5.1 Hardware Setup • Install Reader as described in chapter 2.3. • Switch on reader by pushing yellow button switch located on left side of the reader housing. Switch will be illuminated. If this is not the case, check power supply and correct connection. -
Page 13: Chapter 3: Technical Data
CHAPTER 3 Chapter 3: Technical Data Technical Data Topic Page General ..................... 14 Specification Summary..............14 Packing..................... 15 Storage ..................... 15... -
Page 14: General
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide General The specifications shown below apply to the following Tag-it Reader / Antenna Sets. Specification Summary Table 1 Specification Summary Electrical Data RF power output 120 mW RF-output 800 mW RF-output Operating frequency : 13.56 MHz 2dB max... -
Page 15: Packing
July ′ 99 Chapter 3. Technical Data Environmental Data Operating temperatures -20 to +55 Storage temperatures -40 to +80 Vibration Suited for static application Overall Dimensions (excluding connectors and switch protrusions) and Weight Reader Antenna Dimensions 200 x 112 x 50 (mm) 200 x 112 x 30 (mm) Weight ~ 470 g... -
Page 16: Chapter 4: Regulatory Safety And Warranty Notices
CHAPTER 4 Chapter 4: Regulatory Safety and Warranty Notices Regulatory, Safety and Warranty Notices Topic Page General ..................... 17 Regulatory Notes................17 4.2.1 FCC Notices (U.S.A.)..............17 4.2.2 CE Conformity................18 Safety Precautions ................18 4.3.1 Human Safety ................18 4.3.2 Application Restrictions............. -
Page 17: General
July ′ 99 Chapter 4. Regulatory, Safety and Warranty Notices General The Reader / Antenna Set has been manufactured using state-of-the-art technology in accordance with the recognized safety rules. Observe precautions in operating instructions • Important for the safe use and fault-free operation of the Reader / Antenna Set is the knowledge of and compliance to the appropriate safety regulations. -
Page 18: Ce Conformity
July ′ 99 Tag-it Reader / Antenna Set – Reference Guide 4.2.2 CE Conformity A CE Declaration of Conformity is available for this Tag-it system through TIRIS Sales Offices. Any device or system incorporating the Tag-it reader system, in full or in part, in any other than the originally tested configuration needs to be verified against the European EMC directive. -
Page 19: Application Restrictions
Warranty and Liability The "General Conditions of Sale and Delivery" of Texas Instruments Incorporated apply. Warranty and liability claims for injuries to persons and property damages are void if they are the result of one or more of the following causes: Œ...
Need help?
Do you have a question about the Tag-it RI-K01-320A and is the answer not in the manual?
Questions and answers