Accusound ES 100 Wireless Instruction Manual

Eclipse series home theatre system

Advertisement

Quick Links

Specifications ES 100 Eclipse Series Wireless Loudspeakers

Power
120 Watts power handling all speakers wired
Frequency Response
125~20000Hz
Efficiency
88 dB@1watt 1 metre
Impedance
8 Ohms nominal
Components
2 x 75mm paper cone drivers
1 x 25mm silk soft dome tweeter
Connections
Gold plated push terminals
Dimensions
Front and rear H x W x D (mm) with base
Centre H x W x D (mm)
Weight
Front kg each, Centre kg, Rear kg each
Transmitter Voltage
100v ~ 240 Volts ~50/60 Hz + ~ - 20%
Transmission
2.4000 ~ 2.4835 GHz with Auto Seeking channels
Rear Speaker Amplifier 100 watts output with adjustable volume level
Colour
Satin black finish
Standby Power
Uses 1 watt or less in auto standby mode

ES 100 Powered Subwoofer Specifications

Power Amplifier
300 watt RMS
Voltage
100 ~240 Volt 50/60Hz +~- 20%
Frequency Response
25~150Hz
Driver
1 x 250mm paper cone driver
Variable 0~10
Phase
Switchable 0~180 degrees
Variable 50~150 Hz
Main Power Switch
Switches Off, On
Standby
Switches On, Auto, Off.
Uses 1 watt or less in auto standby mode
Fuse
Protection 2 amp
Input
L + R RCA, LFE and High Level inputs
Dimensions
H x W x D (mm)
Weight
kg
Colour
Satin black finish
This system complies with AS/NZ4268: 2003
Accusound Australia Pty, Ltd
Unit 3, 17-19 Marshall Road,
Kirrawee NSW 2232
Ph (02) 9545-3905 Fax (02) 9545-3902
Email:
info@accusound.com.au
www.accusound.com.au
2013
Eclipse Series Home
Theatre System
ES 100 Wireless
Instruction Manual
Please read these instructions carefully
before turning on your speakers.

Contents

Carton 1
2 x Front speakers
1 x Centre speaker / Wireless Transmitter
2 x Wireless surround speakers
4 x Front & rear speaker bases
3 x AC Power leads for wireless transmitter and 2 surrounds
8 x 30mm screws for bases
Carton 2
1 x Powered Subwoofer

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ES 100 Wireless and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Accusound ES 100 Wireless

  • Page 1 2.4000 ~ 2.4835 GHz with Auto Seeking channels Rear Speaker Amplifier 100 watts output with adjustable volume level Colour Satin black finish ES 100 Wireless Standby Power Uses 1 watt or less in auto standby mode Instruction Manual ES 100 Powered Subwoofer Specifications...
  • Page 2 All receivers have an auto speaker set up. They have a microphone that sets the level of each system on the market today. The ES 100 Wireless system has been designed to work on any digital speaker. The ES 100 Wireless rear surrounds are powered and your receiver will not understand that receiver on the market.
  • Page 3 Subwoofer Control Panel Phase Switch This function adjusts the phase of the subwoofer driver. This adjustment is required to ensure that the subwoofer and all other associated loudspeakers operate "in sync." If your main speakers are at the front of the room the woofers are pushing forward. If your subwoofer is at the front of the room the woofer will be pushing forward.
  • Page 4 Speaker Terminals Speaker wire can be inserted into the hole in the shaft of the speaker’s and transmitter terminals. Simply strip away approximately 10mm of the wire jacket, push the connection terminal in and insert the wire through the hole in the shaft. Release the terminal and it holds the speaker wire in place. Make sure no stray wire strands touch the opposite terminal.

Table of Contents