Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Priefert LOG22
- Page 1 VERTICAL/HORIZONTAL LOG SPLITTERS MODEL NO. LOG22 22 TON Owner’s Manual ASSEMBLY & OPERATING INSTRUCTIONS MODEL NO. LOG34 MODEL NO. LOG28 34 TON 28 TON THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL LS123-806-0909 Rev 0...
-
Page 2: Table Of Contents
Operation of the Log Splitter ....................Repair and Maintenance Safety ..................... Hydraulic Safety ........................Fire Prevention ........................Towing Safety ........................Assembly Instructions ........................7-19 LOG22 ..........................LOG28 ..........................11-13 LOG34 ..........................16-19 Operating Instructions ........................22-23 Engine Oil Recommendations .................... -
Page 3: Important Safety Information
WARNING: Read and thoroughly understand all instructions and safety information before assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment a log splitter can be dangerous if assembled or used improperly. - Page 4 PART NUMBER: 52055200 LOCATION: TOP, FORWARD SECTION OF CYLINDER AND SIDES OF STRIPPER PLATES PART NUMBER: 52023200 LOCATION: HYDRAULIC TANK LOWER TANK, RIGHT CORNER PART NUMBER: 51018900 LOCATION: TOP OF HYDRAULIC CYLINDER Page 2...
-
Page 5: General Safety
ENGINE OPERATION OF THE LOG SPLITTER Operator Zone LOG22 MODEL ONLY operate the log splitter from the operator zone* as shown in the diagrams. The operator has the safest and most efficient access to the control valve and beam in... -
Page 6: Repair And Maintenance Safety
KNOW how to stop the log splitter and disengage the controls before operating it. NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke. Serious injury or death could result. NEVER straddle or step over the log splitter during operation. NEVER reach or bend over the log splitter to pick up a log. -
Page 7: Hydraulic Safety
HYDRAULIC SAFETY The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hose and components. NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible. Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death. -
Page 8: Towing Safety
IMPORTANT NOTE: This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark ar- rester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective working order by the operator. -
Page 9: Assembly Instructions
ASSEMBLY INSTRUCTIONS LOG22 NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become neces- sary to disassemble the unit for repair or replacement of parts 401411B22 Beam Assembly 401193B22 Tank/Engine Assembly... - Page 10 STEP 3: Attach the tongue assembly (5) to the tank assembly (4) using two 1/2” NC x 4-1/2” hex cap bolts (1), two 1/2” lock washers (2) and two and two 1/2” hex nuts. Tighten. (3).Tighten. ITEM NO PART NO. DESCRIPTION QTY.
-
Page 11: Log22
STEP 5: Connect the end of the 1/2” ID x 44” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve . See illustrations below. STEP 6: Slide one hose clamp on the end of the 3/4” x 44” hydraulic return hose (3) that comes from the fitting on the filter . - Page 12 BEAM ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 1/2” X 3-1/4” GR 5 Hex Cap Bolt 1/2” Regular Lock Washer 1/2” Hex Nut 401411PB Beam 40141700 Wedge 390118BC 4” Cylinder 07073100 Cylinder Pin 390406SC Valve 39034700 1/2” Pipe to Steel To Steel Tube 39034300 1/2”...
-
Page 13: Log28
ASSEMBLY INSTRUCTIONS LOG28 NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become neces- sary to disassemble the unit for repair or replacement of parts 401612PB Beam Assembly 40127500 Beam Lock Assembly 401609PB Tank Assembly 400312B0... - Page 14 STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock washers (3) and two and two 1/2” hex nuts (4). Tighten. ITEM NO. PART NO. DESCRIPTION QTY.
- Page 15 STEP 5: Connect the end of the 1/2” ID x 44” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve. See illustrations below. STEP 6: Slide one hose clamp on the end of the 3/4” x 44” hydraulic return hose (2 ) that comes from the fitting on the filter.
-
Page 16: Log28
TANK/ENGINE ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 5/16”-18 UNC Nylock Nut 5/16” Flat Washer 5/16” x 1-1/2” GR5 Hex Bolt 39027400 Return Line Hose 39027500 1/2” x 38” Hydraulic Pressue Hose 1 39032000 3/4” NPT x 3/4” Tube 39034900 3/4”... - Page 17 BEAM ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION 1/2” Hex Nut 1/2” Regular Lock Washer 1/2” x 3-1/4” Hex Bolt 390119B0 4.5” x 24” Hydraulic Cylinder 39032000 3/4” NPT x 3/4” Tube 39034300 1/2” NPT Nipple 39034600 1/2” Steel Tubing 39034700 1/2”...
-
Page 18: Log34
ASSEMBLY INSTRUCTIONS LOG34 NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become necessary to disassemble the unit for repair or replacement of parts ITEM NO. PART NO. DECSRIPTION QTY. 401610PB Beam Assembly 40127500... - Page 19 STEP 1: Remove all the components from the shipping container.Inspect each piece for shipping damage. If any part is damaged, contact your dealer or delivering carrier. STEP 2: Attach the two wheels (1) to the tank assembly wheel spindles using the 3/4” light flat washers(2) ,3/4” NF slotted nuts (3), 1/8”...
- Page 20 STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam is stable and on a level surface.Remove the pivot pin (3) and clip pin (2) from the tank assembly.Roll the tongue/ tank assembly into position between the two tabs on the beam (1).
- Page 21 STEP 7: Attach the latch to the bottom side of the beam as shown in the diagram using the two 1/2” x 1-1/4” Grade 5 hex cap bolts, the two 1/2” lock washers ( ) and the two 1/2” hex nuts ( ). Lower the beam onto the tongue. Position the latch assembly on the tongue and tighten hardware.
-
Page 22: Log34
TANK/ENGINE ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 5/16”-18 UNC Nylock Nut 5/16” Flat Washer 5/16” x 1-1/2” GR5 Hex Bolt 39027400 3/4” Return Line Hose 39027500 1/2” x 38” Hydraulic Pressue Hose 1 39032000 3/4” NPT x 3/4” Tube 39034900 3/4”... - Page 23 BEAM ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION 1/2” Hex Nut 1/2” Regular Lock Washer 1/2” x 3-1/4” Hex Bolt 390117B0 5” x 24” Hydraulic Cylinder 39032000 3/4” NPT x 3/4” Tube 39034300 1/2” NPT Nipple 39034600 1/2” Steel Tubing 39034700 1/2”...
-
Page 24: Operating Instructions
OPERATING INSTRUCTIONS WARNING: Read and thoroughly understand all instructions and safety information before operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment a log splitter can be dangerous if it is assembled or used improperly. -
Page 25: Towing
c) Grasp starter handle and pull rope out slowly until resistance is felt. Then pull rope rapidly with full arm stroke. Let rope return to starter slowly. d) When engine starts, leave the control lever at “FAST.” The throttle must be in the “FAST” position for maximum performance. STEP 2: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. -
Page 26: Notes
IMPORTANT NOTICE We, the manufacturer, reserve the right to change the product and/or specifications in this manual without notification. The manual is for information usage only and the pictures and drawings depicted herein are for reference only. NOTES Model No. ____________________ Serial No. -
Page 27: Specifications
SPECIFICATIONS & o t t & o t t & o t t " 4 " 4 " 2 " 4 " 5 " 4 " 6 " 6 " 6 " 8 c i t " 8 c i t "...
Need help?
Do you have a question about the LOG22 and is the answer not in the manual?
Questions and answers