Operating A Cable Box Or Dbs Receiver; Setting The Manufacturer's Code - Sony KP-53XBR300 Operating Instructions Manual

Operating a Cable Box
or DBS Receiver
Setting the Manufacturer's
Code
You can program the supplied remote control to
operate a cable box or DBS receiver.
Press CODE SET, DBS/CABLE (FUNCTION),
and the 0-9 buttons to enter the manufacturer's
code number (see the following chart), then press
ENTER.
For example, to operate a Sony DBS receiver:
FUNCTION
CODE SET DBS/CABLE
8
54
M M M M anu anuf f f f ac
anu anu
box) ) ) ) box
box box
Manufacturer
Gemini
Hamlin/Regal
Jerrold/G. I.
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
Samsung
Scientific Atlanta
Tocom
Zenith
ENTER
M M M M anu anuf f f f ac anu anu
0
1
r r r r ece ecei i i i v v v v e e e e r r r r ) ) ) ) ece ece
Manufacturer
Sony
General Electric
RCA/PROSCAN
Operating a cable box or DBS
receiver
1
Press DBS/CABLE (POWER) [Green Button]
to turn on/off the cable box or DBS receiver.
2
Press DBS/CABLE (FUNCTION).
3
For other operations, refer to the operating
instructions that come with the equipment.
Blue-labeled buttons such as the GUIDE
button can be used only with a DBS receiver.
act t t t u u u u r r r r e e e e r r r r code nu code num m m m b b b b e e e e r r r r s s s s ( ( ( ( cab
ac ac code nu code nu
Code
233
222, 223, 224, 225, 226
201, 202, 203, 204, 205, 222,
206, 207, 208, 218
230, 231, 232
234
227, 228, 229
219, 220, 221
236, 237, 238, 239, 240, 241
214, 215
235
209, 210, 211
216, 217
212, 213
act t t t u u u u r r r r e e e e r r r r code nu ac ac code num m m m be code nu code nu ber r r r s s s s ( ( ( ( D D D D B B B B S S S S be be
Code number
801 (preset code for remote
control)
802
802
cabl l l l e e e e If If If If t t t t h h h h e e e e r r r r e e e e m m m m o o o o t t t t e con e cont t t t r r r r o o o o l l l l doe
cab cab e con e con
• Try repeating the set up procedures using the
other codes listed for your equipment.
T T T T o o o op p p p e e e e r r r r a a a a t t t t e e e e t t t t he p he pr r r r o o o o j j j j ec
o o o o he p he p
Press TV (FUNCTION). Then use the projection
TV control buttons to control the projection TV.
Tips z
• If more than one code number is listed, try entering
them one by one until you come to the correct code
for your equipment.
• If you enter a new code number, the code number
you previously entered at that setting is erased.
• In some rare cases, you may not be able to operate
your equipment with the supplied remote control. In
this case, use the equipment's own remote control
unit.
• Whenever you remove the batteries — to replace
them, for example — if too much time is taken, the
code numbers may revert to the factory setting and
must be reset.
does s s s n n n n ' ' ' ' t t t t w w w w o o o o r r r r k k k k
doe doe
ect t t t i i i i on on T T T T V V V V
ec ec on on