Table of Contents
Advertisement
(3) After pressing ADJ key on Remote Control for adjustment,
select the adjustment mode 5. Uniformity adj.
Refer to register value and correct register value if need.
<Resister Explanation about uniformity adjustment>
1. RamCtrl : s/w saving uniformity write order(Do not adjust)
2. CSHP : Horizontal start point designation ---adjustable
3. CSVP : Vertical start point designation ---adjustable
4. CEHP : Horizontal END point designation ---adjustable
5. CEVP : Vertical END point designation ---adjustable
6. Mode : uniformity mode select --- adjustable if need
*** 0 : 221point & 3level ---- default value
*** 1 : 221point & 4level
*** 2 : 825point & 3level
*** 3 : 825point & 4level
7. KHH : Upper 2byte of horizontal line correction coefficient --
Change according to CSHP, CEHP value.
8. KHL : Upper 2byte of vertical line correction coefficient --
Change according to CSHP, CEHP value.
** How to calculate KHH, KHL value
LCD panel size = 1280 x 720
Correction Point = 221 point
--> 17 horizontal points x 13 vertical points
(16 horizontal segments x 12 vertical points)
H Coefficient(KHH, KHL)
O
--> Calculation method (CEHP-CSHP=1280, Horizontal
segment value =16)
H coefficient = 1/(number of pixel intervals between setting in the horizontal
direction)
Hcoeff = 1/((1280/16)-1) = 0.012658227
hex(0.012658227 x 2
16
) = 0 x 033D, Hcoeff(hex) = 0 x 033D + 1 = 0 X 33E
9. KVH : Upper 2byte of vertical line correction coefficient --
Change according to CSVP, CEVP value.
10. KVL : Upper 2byte of vertical line correction coefficient --
Change according to CSVP, CEVP value.
V Coefficient(KVH, KVL)
O
--> Calculation method (CEVP-CSVP=720, Vertical segment
value =12)
V coefficient = 1/(number of pixel intervals between setting in the horizontal
direction)
Vcoeff = 1/((720/12)-1) = 0.016949152
hex(0.016949152 x 2
16
) = 0 x 0456, Vcoeff(hex) = 0 x 0456 + 1 = 0 X 0457
11. RL1H : Upper 9bit of MID2 brightness correction coefficient in
R MIN.
--- Change according to RMIN and RMID2 value.
12. RL1L : Lower 9bit of MID2 brightness correction coefficient in
R MIN.
--- Change according to RMIN and RMID2 value.
13. RL2H : Upper 9bit of MID1 brightness correction coefficient in
R MID2.
--- Change according to RMID2 and RMID1 value.
ADJUSTMENT INSTRUCTIONS
14. RL2L : Lower 9bit of MID1 brightness correction coefficient in
R MID2.
--- Change according to RMID2 and RMID1 value.
15. RL3H : Upper 9bit of MAX brightness correction coefficient in
R MID1.
--- Change according to RMID1 and RMAX value.
(use it while adjusting 4 coefficient)
16. RL3L : Lower 9bit of MAX brightness correction coefficient in
R MID1.
--- Change according to RMID1 and RMAX value.
(use it while adjusting 4 coefficient)
<L Coefficient Calculation Method>
Using 3coefficient Level
Assume that the value of R/G/B MIN, MID2,MID1 is 192, 448,
704.
R/G/B MIN = 192
R/G/B MID2 = 448
R/G/B MID1 = 704
L Coefficient(RL1H~BL3L)
O
--> Calculation method (L1)
L1 coefficient = 1 / (brightness level(MID2) - brightness level(MIN)
L1coeff = 1 / (448-192) = 1 / 256 = 0.00390625
L1coeff(hex) = hex(0.00390625 x 2
--> L1H(high 9bit) = b'000000010 L1L(low 9bit) = b'000000000
- calculate L2, L3 same with L1
L2 coefficient = 1 / (brightness level(MID1) - brightness level(MID2)
L3 coefficient = 1 / (brightness level(MAX) - brightness level(MID1)
: case of 4 Brightness Level
17. GL1H : Upper 9bit of MID2 brightness correction coefficient in
G MIN.
--- Change according to GMIN and GMID2 value.
18. GL1L : Lower 9bit of MID2 brightness correction coefficient in
G MIN.
--- Change according to GMIN and GMID2 value.
19. GL2H : Upper 9bit of MID1 brightness correction coefficient in
G MID2.
--- Change according to GMID2 and GMID1 value.
20. GL2L : Lower 9bit of MID1 brightness correction coefficient in
G MID2.
--- Change according to GMID2 and GMID1 value.
21. GL3H : Upper 9bit of MAX brightness correction coefficient in
G MID1.
--- Change according to GMID1 and GMAX value.
(use it while adjusting 4 coefficient)
22. GL3L : Lower 9bit of MAX brightness correction coefficient in
G MID1.
--- Change according to GMID1 and GMAX value.
(use it while adjusting 4 coefficient)
23. BL1H : Upper 9bit of MID2 brightness correction coefficient in
B MIN.
--- Change according to BMIN and BMID2 value.
24. BL1L : Lower 9bit of MID2 brightness correction coefficient in
B MIN.
- 15 -
18
) = 0 x 0400
Advertisement
Table of Contents
