Download  Print this page
   

Advertisement

Indicator
VCR1
ON•OFF
TV
DVD
VCR2
AUX
SAT•CABLE
MUTE
SKIP
SOUND
GO BACK
GUIDE
INFO
OK
MENU
CLEAR
1
2
3
4
5
6
7
8
9
WHO•INPUT
ANTENNA
0
REVERSE
PLAY FORWARD
REC•VCR+
STOP
PAUSE
PIP
SWAP
CH CTRL
RESET
Important: The remote may
not be compatible with all
brands and models of
components. It also may not
operate all functions of the
remote that came with your
component.
Programming Instructions for Your
CRK76 Remote
The CRK76 universal remote can be programmed to control most brands
of remote controllable TVs, VCRs, satellite receivers, DVD players, audio
receivers, and cable boxes. The remote is already programmed to control
most RCA, PROSCAN, and GE components.
Also, the AUX button can be programmed to control most brands of an
additional remote-controllable component.
The following programming instructions are for all models of the CRK76
remote control. Keep in mind that your model of CRK76 may have
different component buttons than other CRK76 models. In addition, a
component button may be labeled slightly different than explained here.
(For example, VCR and VCR1, or SAT-CABLE and DIRECTV).
Test the Remote
To determine whether the universal remote needs to be programmed for
your component, turn the component ON. For example, to program the
remote for a VCR, turn on the VCR. Point the remote at the VCR, and
press the VCR1 button. Then press ON•OFF or CH + (channel up) or
CH –(channel down) to see if the VCR responds to the remote
commands. If the component does not respond, the remote needs to be
programmed.
Program the Remote
There are two ways to program the remote control:

automatic code search

direct entry
Automatic Code Search
The following instructions can be used to program the remote to operate
each of your components. If you want to exit the automatic code search
without programming any of your components, press CLEAR until the
indicator on the remote turns off.
Note: The AUX button can't be programmed using
automatic code search. It must be programmed using the
direct-entry method.
1. Turn on the component you want to operate (VCR, TV, etc.)
2. Press and hold the component button you want to program (VCR1,
VCR2, etc.). While holding the component button, press and hold
ON•OFF until the indicator on the remote turns on, then release
both buttons.

Advertisement

Table of Contents

   Related Manuals for RCA CRK76

   Summary of Contents for RCA CRK76

  • Page 1: Automatic Code Search

    Also, the AUX button can be programmed to control most brands of an additional remote-controllable component. The following programming instructions are for all models of the CRK76 remote control. Keep in mind that your model of CRK76 may have different component buttons than other CRK76 models. In addition, a SOUND...
  • Page 2: Programming Your Remote

    Programming Your Remote 3. Point the remote at the component. Press and release PLAY, then wait 5 seconds or until the indicator on the remote stops flashing. At this point the remote is searching for the correct code to program. If, after 5 seconds, the component you want to operate does not turn off, press PLAY again to tell the remote to search the next set of codes.
  • Page 3: Operate Components After Programming Remote

    Programming Your Remote Operate Components after ON•OFF button Programming the Remote Because this universal remote can control several different components VCR1 ON•OFF (TV, DVD, VCR, satellite receiver, etc.) it uses operational modes triggered by the component buttons. For example, if you want the VCR2 SAT•CABLE remote to control the TV, you would press the TV button to put the...
  • Page 4: Vcr Codes

    ....1012, 1038, 1049, 1095, 1162, 1171, 1172 ....1143, 1144, 1145, 1146, 1148, 1150, 1179 Beaumark ............... 2013 RCA ...... 1000, 1003, 1004, 1005, 1006, 1007, IMA ................ 1038 Broksonic ............. 2012, 2025 ....1019, 1096, 1098, 1099, 1100, 1101, 1102 Infinity ..............
  • Page 5: Cable Box Codes

    Quasar ..........2021, 2022, 2125 Fuji ..............2021, 2119 Hitachi ..............5003 Funai .............. 2002, 2026 RCA ....2000, 2001, 2003, 2013, 2021, 2055, 2056, Hytex ..............5002 ..2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089, Garrard ..............2026 Jasco ...............
  • Page 6: Satellite Receiver

    Sony ............4266, 4271, 4272, 4281 Primestar ............... 5076 Technics ..............4279, 4280 PROSCAN ..... 5000, 5001, 5071, 5080, 5081 Wards .................. 4275 RCA ....... 5000, 5001, 5071, 5080, 5081 Realistic ..............5063 Yamaha ..............4272, 4274 Sony ..............5072 STS1 ..............5064 STS2 ..............

Comments to this Manuals

Symbols: 0
Latest comments: