Operation; Washing Your Filter - Dyson DC45 Operating Manual

USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.

OPERATION

• Do not allow this appliance to be used by anyone who may not be able to
operate it safely.
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
• Ensure the appliance remains upright in use. Dirt and debris may be released if
it is turned upside down.
• Do not operate while checking for blockages.
• For domestic indoor and car use only. Do not use it whilst the car is in motion or
while driving.
• To watch a short online video visit:
www.english.dysoncanada.ca/dc45gettingstarted
CARPETS OR HARD FLOORS
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• Before vacuuming highly polished floors, such as wood or linoleum, first check
that the underside of the floor tool and its brushes are free from foreign objects
that could cause marking.
LOOKING AFTER YOUR DYSON APPLIANCE
• Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
• Only use parts recommended by Dyson. If you do not this could invalidate your
warranty.
• Store the appliance indoors. Do not use or store it below 0˚C (32˚F). Ensure the
appliance is at room temperature before operating.
• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
VACUUMING
• Do not use without the clear bin and filter in place.
• Fine dirt such as plaster dust or flour should only be vacuumed in very small
amounts.
• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimize any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and rinsed it
out with cold water (see 'Cleaning the clear bin').
• Use extra care when cleaning on stairs.
• Do not rest the appliance on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors the movement of the cleaner head may create an uneven
lustre. If this happens, wipe with a damp cloth, polish the area with wax, and
wait for it to dry.
DIAGNOSTICS – APPLIANCE
Less than one minute of charge remaining/fully discharged.
Too cold/too hot – do not use.
EMPTYING THE CLEAR bIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the appliance is disconnected from the charger before emptying the
clear bin.
• To release the dirt, push the red button at the side of the clear bin as shown.
• To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
• Remove the clear bin carefully.
• Seal the bag tightly, dispose as normal.
• To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
8
CLEANING THE CLEAR bIN
• Ensure the appliance is disconnected from the charger before removing the
clear bin. Be careful not to pull the 'ON' trigger.
• Remove the wand and floor tool.
• To remove the clear bin, push the red button at the side of the clear bin as you
would when emptying the clear bin. This will expose the red release button on
the underside of the handle. Press this to release the clear bin.
• Remove the clear bin carefully.
• Clean the clear bin with a damp cloth only.
• Ensure the clear bin is completely dry before replacing.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put clear bin in a dishwasher.
• Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.
• To replace the clear bin, fit the tab on the rim of the cyclone shroud into the
aperture on the inside of the top of the clear bin. Push the clean bin up and in. It
will click into place.
• Close the base of the clear bin.

WASHING YOUR FILTER

• Ensure the appliance is disconnected from the charger before removing the
filter.
• Your appliance has one washable filter, located as shown.
• Press the 'Filter' button so you can remove the cyclone and clear bin unit.
• Check and wash the filter regularly according to instructions to maintain
performance.
• The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'HIGH CONSTANT SUCTION' mode.
• Wash the filter with cold water only. Do not use detergents.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
IMPORTANT: After washing please leave the filter to dry completely, at least
12 hours, before refitting.
• Place the dry filter into the recess of the handle.
• Fit the base of the handle into the aperture on the base of the cyclone and clear
bin unit. Push both halves together until the 'Filter' button engages and locks into
place.
• To watch a short online video visit:
www.english.dysoncanada.ca/dc45filterwash
LOOKING FOR bLOCKAGES
• Ensure the appliance is disconnected from the charger before looking for
blockages.
• Do not operate while checking for blockages. Failure to do so could result in
personal injury.
• Beware of sharp objects when checking for blockages.
• Refit all parts securely before using.
• Clearing blockages is not covered by your warranty.
• If you cannot clear an obstruction you may need to remove the brush bar.
Use a coin to unlock the fastener marked with a padlock. Remove the
obstruction. Replace the brush bar and secure it by locking the fastener.
Ensure it is fixed firmly before operating the appliance.
• Take care if coming into contact with the carbon fibre brushes, as they may
cause minor skin irritation. Wash your hands after handling the brushes.
CLEARING bLOCKAGES – THERMAL CUT-OUT
• This appliance is fitted with an automatically resetting thermal cut-out.
• Large items may block the tools or nozzle. If any part becomes blocked the
appliance may overheat and automatically cut-out.
• Leave to cool down for 1-2 hours before checking the filter or for blockages.
• Ensure the appliance is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury.
• Clear any blockage before restarting.
• Refit all parts of the appliance securely before using.
• Clearing blockages is not covered by your warranty.
CHARGING AND STORING
• This appliance will switch 'OFF' if the battery temperature is below 3°C (37.4°F).
This is designed to protect the motor and battery. Do not charge the appliance
and then move it to an area with a temperature below 3°C (37.4°F) for storage
purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the appliance with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.
• If mounting the docking station on a wall, follow the instructions supplied with
this appliance. Ensure the docking station is fitted correctly and the right way
up, so the motor of the appliance is at the top when in place. Take all necessary
safety precautions. Use appropriate fixings, tools and safety equipment.