Advertisement
To reduce the risks associated with impact from abrasive product or tool breakup, sharp edges, hazardous pressure, rupture, vibration and noise:
• Read, understand and follow the safety information contained in these instructions prior to the use of this tool. Retain these instructions for future
reference.
• Only personnel who are properly trained should be allowed to service this tool.
• Practice safety requirements. Work alert, have proper attire, and do not operate tool under the influence of alcohol or drugs.
• Operators and other personnel must always wear protection for eyes, ears, and respiratory protection when in the work area or while operating this
product. Follow your employer's safety policy for PPE's and/or ANSI Z87.1 or local/national standards for eyewear and other personal protective equipment
requirements.
• Wear protective apparel, taking into consideration the type of work being done.
• Never exceed marked maximum input pressure (90psi / .62Mpa / 6.2Bars).
• Proper eye protection must be worn at all times.
• Tool shall not be operated in the presence of bystanders.
• If you notice any abnormal noise or vibration when operating the product, immediately discontinue its use and inspect for worn or damaged components.
Correct or replace the suspect component. If abnormal noise or vibration still exists, return the tool to 3M for repair or replacement. Refer to warranty
instructions.
• Never operate this tool without all safety features in place and in proper working order.
• Never over-ride or disable the safety features of the start-stop control such that it is in the on position.
• Make sure the tool is disconnected from its air source before servicing, inspecting, maintaining, cleaning, and before changing abrasive product.
• Prior to use, inspect abrasive product and accessories for possible damage. If damaged, replace with new abrasive product and accessories available from 3M.
• Only use accessories supplied or recommended by 3M.
• Use only with mounting hardware recommended by 3M; check with 3M for mounting hardware requirements.
• Always ensure that shaft diameters match internal diameters of the collet inserts.
• Maximum operating speed of abrasive products or accessories must be reduced whenever the exposed length of shaft (overhang) is longer than
corresponding 3M approved products.
• Always ensure that a minimum of 10mm shaft gripping length is observed.
• Never install and use router bits or cutting-off wheels in a die grinder tool (which is unguarded).
• Use only with abrasive products not requiring guards according to local, state and federal regulations.
• Never allow this tool to be used by children or other untrained people.
• Do not leave an unattended tool connected to air source.
• Air under pressure can cause severe injury.
• Never direct air at yourself or anyone else.
To reduce the risk of all hazards associated with vibration:
• If any physical hand/wrist discomfort is experienced, work should be stopped promptly to seek medical attention. Hand, wrist and arm injury may result
from repetitive work, motion and overexposure to vibration.
• Hold the tool with a light but safe grip, knowing that the grip must be sufficient to counter reaction forces but that a tight grip will increase the amount of
vibration transferred to the operator.
To reduce the risks associated with loud noise:
• Always wear protection for eyes, ears, and respiratory protection while operating this product. Follow your employer's safety policy for PPE's and/or ANSI
Z87.1 or local/national standards for eyewear and other personal protective equipment requirements.
• Always wear hearing protection while operating this tool. Follow your employer's safety policy or local/national standards for personal protective
equipment requirements.
• Ensure the muffler material is in place.
• Dampen work pieces to reduce noise and prevent ringing.
To reduce the risk associated with fire or explosion:
• Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The abrasives are able to create sparks
when working material, resulting in the ignition of the flammable dust or fumes.
• Refer to MSDS of material being worked as to potential for creating fire or explosion hazard.
To reduce the risk associated with hazardous dust ingestion or eye/skin exposure:
• Use appropriate respiratory and skin protection, or local exhaust as stated in the MSDS of the material being worked on.
• Direct exhaust so as to minimize disturbance of existing dust in a dust-filled environment.
To reduce the risk associated with hazardous voltage:
• Do not allow this tool to come into contact with electrical power sources as the tool is not insulated against electrical shock.
To reduce the risk associated with skin abrasion, burns, cuts, or entrapment:
• Keep hands, hair, and clothing away from the rotating part of the tool.
• Wear suitable protective gloves while operating tool.
• Do not touch the rotating parts during operation for any reason.
• Do not force tool or use excessive force when using tool.
To reduce the risk associated with whipping or hazardous pressure-rupture:
• Ensure supply hose is oil resistant and is properly rated for required working pressure.
• Do not use tools with loose or damaged air hoses or fittings.
• Be aware that incorrectly installed hoses and fittings might unexpectedly come loose at any time and create a whipping/impact hazard.
• Whenever universal twist couplings (claw couplings) are used, lock-pins shall be installed and whip check safety cables shall be used to safeguard
against possible hose-to-tool and hose-to-hose connection failure.
To reduce the risk associated with fly off of abrasive product or parts:
• Use care in attaching abrasive product and mounting hardware; following the instructions to ensure that they are securely attached to the tool before use
or free-spinning.
• Never point this product in the direction of yourself or another person, or start tool unintentionally.
• Never over-tighten accessory fasteners.
WARNING
CAUTION
2
Advertisement
