S-Video IN Y : 1V p-p 75W This service manual should be used in conjunction NOTE : (21 pin ) C : 0.3V p-p 75W with the EURO 2 technical guide. Panasonic CS (UK) Panasonic WILLOUGHBY ROAD, BRACKNELL BERKS, RG12 8FT.
Contents Safety Precautions Location of Controls Chassis Service Position Service Mode Self Check Adjustment Procedure Alignment Settings Waveform Pattern Table Block Diagrams P.C.B. Views Schematic Diagrams Parts Location Replacement Parts List Safety Precautions General Guide Lines It is advisable to insert an isolation transformer in the AC su p ply Check each exposed Metallic part and check the voltage at each before servicing a hot chassis.
Location Of Controls FOCUS SCREEN Fig.2 Service Hints How to remove the rear cover Remove the 5 fixing screws (A) as shown in Fig.3/Fig.4. SCREW Fig.4 SCREWS (A) Fig.3.
Page 4
How to move the chassis into the Service position NOTE: To place the chassis into the advised service position the T.V. must be on the T.V. stand provided with the set. To place the chassis into service position hold and lift the rear of the E-PCB chassis and gently pull the chassis toward you as shown in Fig.5. B-PCB service position Release the respective wiring clips and rotate the chassis horizontally through 90_ anti-clockwise, then lift the front of the chassis as shown in...
TX-21AD2 Service Mode The remote control is used for entering and storing adjustments, with the exception of cut-off adjustments which must always be done prior to service adjustment. Perform adjustments in accordance with screen display. The display on the screen also specifies the CCU variants as well as the approx.
TX-21AD2 SELF CHECK Self check used automatically check lines Hexadecimal code set. To enter the Self Check mode press Function down button, on the Preset Panel, at the same time pressing the Status button, on the Remote Control, and the screen will show:-...
Page 7
TX-21AD2 Alignment Settings (The figures used below are nominal and used for representative purposes only) Alignment Function TX-21AD2 Settings / Special features Vertical amplitude V-AMP Optimum setting Vertical symmetry V-SYM Optimum setting Vertical linearity V-LIN Optimum setting -020 Vert. D.C.
Page 9
X103 TUNER FILTER IC102 VIDEO Q103 BUFFER Q3006 TUNER BUFFER VIDEO IN Q3001 IC3001 BUFFER Q3005 BUFFER 10 8 Q3004 BUFFER IC3501 MEMORY IC601 VIDEO IC3502 TELETEX H OUT Q302 Q307 Q301 Q351 BUFFER OUTPUT AMP IC351 Q304 Q308 Q303 Q352 RGB AMPS BUFFER...
Page 10
MUTE SIGNAL LEFT AUDIO IC102 X103 Q102 Q101 RIGHT AUDIO TUNER SIF/VIF/DEMODULATOR FILTER BUFFER IF SIGNAL Q202 Q201 BUFFER Q2102 AV1 IN BUFFER I251 AV1 OUT AUDIO OUTPUT IC2101 Q2101 AUDIO BUFFER PROCESSOR AV2 IN AV2 OUT AV3 IN AV2 OUT Q2310 Q2309 Q2306...
Page 12
TP’S TRANS TPY1 Q351 TPY2 Q352 TPY3 Q353 TPY4 TPY5 IC’S TPY6 IC351 Y BOARD TNP117069...
Page 14
SCHEMATIC DIAGRAM FOR MODELS TX-21AD2 (EURO-2S CHASSIS) IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. Notes RESISTOR All resistors are carbon ¼W resistor, unless marked.
Page 19
The numbers on the exploded view below refer to the miscellaneous section of the Replacement Parts List.
Need help?
Do you have a question about the TX-21AD2 and is the answer not in the manual?
Questions and answers